Date: Mon, 7 May 2007 18:05:27 -0600 From: "David Kalliecharan" <davidkallie@gmail.com> To: freebsd-questions@freebsd.org Subject: Sound driver problem Message-ID: <7b0c7ad70705071705y6473a657w810415140c5637ea@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Hello,
I have a problem running sound, I followed the guide but it doesn't work. I
am using a Compaq Prescario v6000 with a AMD sempron and Nvidia go 6150. I
ran:
#kldload snd_driver
and it gave this
# cat /dev/sndstat
FreeBSD Audio Driver (newpcm)
Installed devices:
also dmesg gave this:
# dmesg
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <HP APIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Mobile AMD Sempron(tm) Processor 3500+ (1808.24-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x40fc2 Stepping = 2
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
Features2=0x2001<SSE3,CX16>
AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow+,3DNow>
AMD Features2=0x19<LAHF,<b3>,CR8>
real memory = 938475520 (895 MB)
avail memory = 900784128 (859 MB)
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <HPQOEM SLIC-MPC> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link9: BIOS IRQ 10 for 0.10.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.0 (no driver attached)
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
pci0: <memory, RAM> at device 0.6 (no driver attached)
pci0: <memory, RAM> at device 0.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci3: <ACPI PCI bus> on pcib2
pci3: <network> at device 0.0 (no driver attached)
nvidia0: <GeForce Go 6150> mem
0xb2000000-0xb2ffffff,0xc0000000-0xcfffffff,0xb1000000-0xb1ffffff irq 18 at
device 5.0 on pci0
nvidia0: [GIANT-LOCKED]
pci0: <memory, RAM> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> port 0x1d00-0x1d7f at device 10.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
pci0: <processor> at device 10.3 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xb0004000-0xb0004fff irq 22 at
device 11.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xb0005000-0xb00050ff irq 22
at device 11.1 on pci0
ehci0: [GIANT-LOCKED]
usb1: EHCI version 1.0
usb1: companion controller, 8 ports each: usb0
usb1: <EHCI (generic) USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
atapci0: <nVidia nForce MCP51 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3080-0x308f at device 13.0 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <nVidia nForce MCP51 SATA300 controller> port
0x30c0-0x30c7,0x30b4-0x30b7,0x30b8-0x30bf,0x30b0-0x30b3,0x3090-0x309f mem
0xb0006000-0xb0006fff irq 23 at device 14.0 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pci_link0: BIOS IRQ 11 for 7.5.INTA is invalid
pci_link1: BIOS IRQ 11 for 7.5.INTB is invalid
pci7: <ACPI PCI bus> on pcib3
fwohci0: <1394 Open Host Controller Interface> mem 0xbc000000-0xbc0007ff irq
9 at device 5.0 on pci7
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:24:1b:00:b7:bb:0b:00
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:24:1b:bb:0b:00
fwe0: Ethernet address: 02:24:1b:bb:0b:00
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci7: <base peripheral> at device 5.1 (no driver attached)
pci7: <base peripheral> at device 5.2 (no driver attached)
pci7: <base peripheral> at device 5.3 (no driver attached)
pci7: <base peripheral> at device 5.4 (no driver attached)
pci0: <multimedia> at device 16.1 (no driver attached)
nve0: <NVIDIA nForce MCP13 Networking Adapter> port 0x30e0-0x30e7 mem
0xb0008000-0xb0008fff irq 20 at device 20.0 on pci0
nve0: Ethernet address 00:1b:24:13:55:36
miibus0: <MII bus> on nve0
rlphy0: <RTL8201L 10/100 media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
nve0: Ethernet address: 00:1b:24:13:55:36
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xcf800-0xd0fff on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1808240932 Hz quality 800
Timecounters tick every 1.000 msec
acd0: DVDR <HL-DT-ST DVDRAM GSA-4084N/KQ09> at ata0-master PIO4
ad4: 114473MB <Seagate ST9120821AS 7.24> at ata2-master SATA150
Trying to mount root from ufs:/dev/ad4s1a
WARNING: / was not properly dismounted
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
does this mean I cannot use my sound card!? Just so you know I am running
FreeBSD 6.2 Stable, would this be fixed in FreeBSD current? Any information
would be greatly appreciated!
--
Dave
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7b0c7ad70705071705y6473a657w810415140c5637ea>