Date: Tue, 22 Dec 2009 18:42:07 +0000 From: Anton Shterenlikht <mexas@bristol.ac.uk> To: Warren Block <wblock@wonkity.com> Cc: freebsd-questions@freebsd.org, freebsd-sparc64@freebsd.org Subject: Re: Signal over range, WAS: X -configure fails: Number of created screens does not match number of detected devices. Configuration failed. Message-ID: <20091222184207.GA61999@mech-cluster241.men.bris.ac.uk> In-Reply-To: <alpine.BSF.2.00.0912221049100.41771@wonkity.com> References: <20091218133634.GA89155@mech-cluster241.men.bris.ac.uk> <20091219125614.GV74529@alchemy.franken.de> <20091219182004.GA80336@mech-cluster241.men.bris.ac.uk> <20091219200730.GW74529@alchemy.franken.de> <20091219214803.GA10306@mech-cluster241.men.bris.ac.uk> <20091220150005.GA74529@alchemy.franken.de> <20091220221010.GA18788@mech-cluster241.men.bris.ac.uk> <20091220222012.GB74529@alchemy.franken.de> <20091222121533.GA60398@mech-cluster241.men.bris.ac.uk> <alpine.BSF.2.00.0912221049100.41771@wonkity.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Dec 22, 2009 at 11:12:35AM -0700, Warren Block wrote: > On Tue, 22 Dec 2009, Anton Shterenlikht wrote: > > ok, I moved a step further. 'X -configure' is now successful. > > All I had to do is to move the graphics card to another pci > > slot. Perhaps where xvr600 was, is not a standard pci slot > > at all? pgx64 worked fine there in the text mode, but not > > in the graphics mode. > > > > So now I'm stopped with "Signal over range" message reported > > by the monitor firmware (?). > > > > The card seems to be detected, the scan frequencies I put > > are from the manufacturer's specs, but still something is wrong. > > > > I put conf and log files here: > > > > http://seis.bris.ac.uk/~mexas/freebsd/xorg.conf.new > > http://seis.bris.ac.uk/~mexas/freebsd/Xorg.0.log > > Manually setting a single mode is probably the easiest: > > Section "Screen" > Identifier "Screen0" > Device "Card0" > Monitor "Monitor0" > DefaultDepth 24 > SubSection "Display" > Viewport 0 0 > Depth 24 > Modes "1280x1024" > EndSubSection > EndSection > > That might be enough, or you might have to go to 1024x768. You could > limit the entries in the Monitor section to trick the card into picking > a single reasonable mode, like VertRefresh 70, or HorizSync 30-50. > (Assuming this is a CRT. If it's an LCD, use VertRefresh 60.) Warren, thank you, but this doesn't help. I've added: Section "Monitor" Identifier "Monitor0" HorizSync 30-50 VertRefresh 60 EndSection Section "Device" Identifier "Card0" Driver "mach64" BusID "PCI:0:2:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1280x1024" EndSubSection EndSection This is an LCD monitor, and the manuf. specs state max res 1280x1024 horizontal: 30-80 vertical: 50-75 I tried modes down to 800x600 - no change. I noticed also this error: (EE) [drm] drmOpen failed. (EE) MACH64(0): [dri] DRIScreenInit Failed should I add device drm to the kernel? Just to remind, this is sparc64. > Incidentally, Radeon 7000 cards are available in standard PCI for $20 or > so. Not a great card, but quite an upgrade over a Mach64, and supported > by a current driver. wow.. you mean on sparc64? I didn't know. If it'll work on sparc, this would be great. There are many more radeon 7000 on offer than pgx64. many thanks as always anton -- Anton Shterenlikht Room 2.6, Queen's Building Mech Eng Dept Bristol University University Walk, Bristol BS8 1TR, UK Tel: +44 (0)117 331 5944 Fax: +44 (0)117 929 4423
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20091222184207.GA61999>