Date: Wed, 17 Jul 2002 12:24:56 +0200 From: Kurt Erik Lindqvist <kurtis@kurtis.pp.se> To: "M. Warner Losh" <imp@bsdimp.com> Cc: "julian@elischer.org" <julian@elischer.org>, "current@FreeBSD.ORG" <current@FreeBSD.ORG> Subject: Re: NEWCARD Message-ID: <99610000.1026901496@laptop.kurtis.pp.se> In-Reply-To: <20020712.102155.57332421.imp@bsdimp.com> References: <Pine.BSF.4.21.0207092344330.38684-100000@InterJet.elischer.org> <540220000.1026378624@laptop.kurtis.pp.se> <20020712.102155.57332421.imp@bsdimp.com>
next in thread | previous in thread | raw e-mail | index | archive | help
> : 1) When trying to insert a Cisco Aironet 340 adapter, I get thrown to > the : db> prompt after it has found the card (which it seems to do > nicely). If I : boot with it inserted, I only get to the detection, then > the boot stops. At : boot up dmesg says the following on the bridge : > : > : cardbus0: <CardBus bus> on pccbb0 > : pccard0: <16-bit PCCard bus> on pccbb0 > : pccbb1: <TI1450 PCI-CardBus Bridge> mem 0x41180000-0x41180fff irq 11 at > : device 4 > : .1 on pci0 > : cardbus1: <CardBus bus> on pccbb1 > : pccard1: <16-bit PCCard bus> on pccbb1 > > Traceback for the panic? db> trace an_cmd(c199e000,1,0,c199e000,c8740c58) at an_cmd+0x45 an_reset(c199e000,ff11006a,0,0,0) at an_reset+0x1a an_probe(c1b55500) at an_probe+0xcc an_pccard_probe(c1b55500) at an_pccard_probe+0xe pccard_compat_do_attach(c18d0380,c1b55500) at pccard_compat_do_attach+0x3a pccard_compat_attach(c1b55500) at pccard_compat_attach+0x48 device_probe_and_attach(c1b55500) at device_probe_and_attach+0x9c pccard_attach_card(c18d0380) at pccard_attach_card+0x240 pccbb_insert(c0bb7600,c018809c,c18d8000,c8740d34,c020d468) at pccbb_insert+0xde pccbb_event_thread(c0bb7600,c8740d48,c0bc0600,c018809c,0) at pccbb_event_thread+ 0x5d fork_exit(c018809c,c0bb7600,c8740d48) at fork_exit+0x94 fork_trampoline() at fork_trampoline+0x1a It will also give some odd error message on RAM failure and probable hardware error. I have tried with two Wlan cards, the Cisco Aironet 340 and the Netgear MA401. Both behave the same way. My Xircom 10/100 X3201 seems to work though. Removing the Wirleess card and doing 'cont' the system seems to resume just fine though. Best regards, - kurtis - To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?99610000.1026901496>