From owner-freebsd-hardware Tue Feb 10 12:35:09 1998 Return-Path: Received: (from majordom@localhost) by hub.freebsd.org (8.8.8/8.8.8) id MAA08526 for hardware-outgoing; Tue, 10 Feb 1998 12:35:09 -0800 (PST) (envelope-from owner-freebsd-hardware@FreeBSD.ORG) Received: from mail.inconnect.com (nscs29p7.remote.umass.edu [128.119.179.176]) by hub.freebsd.org (8.8.8/8.8.8) with ESMTP id MAA08400 for ; Tue, 10 Feb 1998 12:34:20 -0800 (PST) (envelope-from gp@mail.inconnect.com) Received: (from gp@localhost) by mail.inconnect.com (8.8.8/8.8.8) id PAA02669 for freebsd-hardware@FreeBSD.ORG; Tue, 10 Feb 1998 15:34:30 GMT (envelope-from gp) Message-Id: <199802101534.PAA02669@mail.inconnect.com> Date: Tue, 10 Feb 1998 15:34:25 +0000 (GMT) From: Greg Pavelcak Subject: Promise Ultra-ATA Controller To: freebsd-hardware@FreeBSD.ORG MIME-Version: 1.0 Content-Type: TEXT/plain; CHARSET=US-ASCII Sender: owner-freebsd-hardware@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.org Hello All, Following a note in the mail archives, I added extra wd controller support thus: controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr disk wd2 at wdc1 drive 0 disk wd3 at wdc1 drive 1 controller wdc2 at isa? port "0" bio irq ? flags 0xa0ffa0ff vector wdintr disk wd4 at wdc2 drive 0 disk wd5 at wdc2 drive 1 controller wdc3 at isa? port "0" bio irq ? flags 0xa0ffa0ff vector wdintr disk wd6 at wdc3 drive 0 disk wd7 at wdc3 drive 1 In the standard CMOS setup I said there were no disks on the on-board controllers. I didn't change anything else. There is a quick screen during boot-up that correctly identifies my hard drives on the Promise controller, then there's this about PCI devices Bus No. Dev. No. Func No. Vendor ID Dev. ID Dev Class IRQ 0 1 1 1039 5513 IDE Control 14 0 13 0 1013 00B8 Display Cont NA 0 17 0 105A 4D33 Mass Storage Cont. 11 I thought all this looked promising, but FreeBSD says "not found" for all my controllers. wdc0 at 0x1f0 not found wdc1 at 0x170 not found wdc2 at 0x6000 not found wdc3 at 0x600(?? I don't remember the number) not found Note: I am running Current ca. 2/6/98 and yes I will switch to SCSI when I get some dough. Any advice on how I can get this controller to work would be greatly appreciated. I am getting tired of experimenting. Unplugging and inserting ribbon cables gets to be a pain after a while, especially in a mini-tower. Thanks again. Greg To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe hardware" in the body of the message