From owner-freebsd-current Wed Dec 22 15:15:51 1999 Delivered-To: freebsd-current@freebsd.org Received: from mnw.eas.slu.edu (mnw.eas.slu.edu [165.134.8.248]) by hub.freebsd.org (Postfix) with ESMTP id 78CC414F3F for ; Wed, 22 Dec 1999 15:15:47 -0800 (PST) (envelope-from ejh@ejhslu.eas.slu.edu) Received: from ejhslu.eas.slu.edu (ejhslu.eas.slu.edu [165.134.8.243]) by mnw.eas.slu.edu (8.9.3/8.9.3) with ESMTP id RAA18095 for ; Wed, 22 Dec 1999 17:15:46 -0600 (CST) Received: (from ejh@localhost) by ejhslu.eas.slu.edu (8.9.3/8.9.3) id RAA21917; Wed, 22 Dec 1999 17:15:44 -0600 (CST) Date: Wed, 22 Dec 1999 17:15:44 -0600 (CST) From: "Eric J. Haug" Message-Id: <199912222315.RAA21917@ejhslu.eas.slu.edu> To: current@freebsd.org Subject: Toshiba 2100CDS ata hangs and internal modem Cc: ejh@ejhslu.eas.slu.edu Sender: owner-freebsd-current@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Hi All, This laptop has a couple of problems with FreeBSD-CURRENT of about 1999/12/22 12:00 UTC. The system hangs with the disk drive light on. The output of boot -vc captured from the serial port follows. current of about 1999/12/11 works in PIO mode. The machine has a built-in modem that appears to be on the pci bus. The sio1 probes fail. If the modem is on the pci bus, what would it take to get it going? I noted that sys/dev/sio was purged awhile ago. Has anyone worked on pci serial/parallel stuff, like the SIIG cards? Should sys/dev/ed be used as a model? It also has a soundsystem and CardBus, but first things first. eric haug Saint Louis Univ. avail memory = 29380608 (28692K bytes) bios32: Found BIOS32 Service Directory header at 0xc00f9000 bios32: Entry = 0xfe95a (c00fe95a) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xd1bc pnpbios: Found PnP BIOS data at 0xc00f9040 pnpbios: Entry = f0000:9536 Rev = 1.0 pnpbios: Event flag at 510 pnpbios: OEM ID a934f351 Other BIOS signatures found: ACPI: 000fe660 Preloaded elf kernel "kernel.lt" at 0xc02ff000. md0: Malloc disk Creating DISK md0 pci_open(1): mode 1 addr port (0x0cf8) is 0x8000a050 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06181179) npx0: on motherboard npx0: INT 16 interface i586_bzero() bandwidth = 109757436 bytes/sec bzero() bandwidth = 146092037 bytes/sec apm0: on motherboard apm: found APM BIOS v1.2, connected at v1.2 pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06181179) pcib0: on motherboard found-> vendor=0x1179, dev=0x0618, revid=0x02 class=06-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 found-> vendor=0x11c1, dev=0x0441, revid=0x01 class=07-80-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=3 map[10]: type 1, range 32, base ffefff00, size 8 map[14]: type 3, range 32, base 000002f8, size 3 map[18]: type 1, range 32, base 00001c00, size 8 found-> vendor=0x5333, dev=0x8c01, revid=0x06 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[10]: type 1, range 32, base f8000000, size 26 found-> vendor=0x1033, dev=0x0035, revid=0x02 class=0c-03-10, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[10]: type 1, range 32, base f7fff000, size 12 found-> vendor=0x125d, dev=0x1978, revid=0x10 class=04-01-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[10]: type 1, range 32, base 0000ff00, size 8 found-> vendor=0x1179, dev=0x0102, revid=0x34 class=01-01-f0, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[20]: type 1, range 32, base 00001800, size 4 found-> vendor=0x1179, dev=0x060f, revid=0x07 class=06-07-00, hdrtype=0x02, mfdev=1 subordinatebus=14 secondarybus=14 intpin=a, irq=255 found-> vendor=0x1179, dev=0x060f, revid=0x07 class=06-07-00, hdrtype=0x02, mfdev=1 subordinatebus=15 secondarybus=15 intpin=b, irq=255 pci0: on pcib0 pci0: unknown card (vendor=0x11c1, dev=0x0441) at 7.0 irq 3 vga-pci0: at device 8.0 on pci0 ohci0: irq 11 at device 11.0 on pci0 usb0: OHCI version 1.0 usb0: on ohci0 usb0: USB revision 1.0 uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: unknown card (vendor=0x125d, dev=0x1978) at 12.0 irq 11 ata-pci0: at device 16.0 on pci0 ata-pci0: Busmastering DMA supported ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1800 ata0: mask=03 status0=50 status1=00 ata0: mask=03 status0=50 status1=00 ata0: devices = 0x1 ata0 at 0x01f0 irq 14 on ata-pci0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1808 ata1: mask=03 status0=50 status1=01 ata1: mask=03 status0=00 status1=01 ata1: devices = 0x4 ata1 at 0x0170 irq 15 on ata-pci0 pcic-pci0: at device 19.0 on pci0 PCI Config space: 00: 060f1179 04800007 06070007 00820000 10: 00000000 04800000 00141400 00000000 20: 00000000 00000000 00000000 00000000 30: 00000000 00000000 00000000 000001ff 40: 00011179 000003e1 00000000 00000000 50: 00000000 00000000 00000000 00000000 60: 00000000 00000000 00000000 00000000 70: 00000000 00000000 00000000 00000000 80: 00000000 00000000 00000000 01000000 90: 00000000 00000000 00000000 00000000 Cardbus Socket registers: 00: f000ef6f: f000ef6f: f000e2c3: f000ef6f: 10: f000ef6f: f000ff54: f000e140: f000ef6f: ExCa registers: 00: 13 88 f5 5a 72 d0 80 e1 3f 74 c8 fa 66 8b 46 08 10: 52 66 0f b6 d9 66 31 d2 66 f7 f3 88 eb 88 d5 43 20: 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03 00 00 fb 77 30: a2 86 c4 c0 c8 02 08 e8 40 91 88 fe 28 e0 8a 66 pcic-pci1: at device 19.1 on pci0 PCI Config space: 00: 060f1179 04800007 06070007 00820000 10: 00000000 04800000 00151500 00000000 20: 00000000 00000000 00000000 00000000 30: 00000000 00000000 00000000 000002ff 40: 00011179 000003e1 00000000 00000000 50: 00000000 00000000 00000000 00000000 60: 00000000 00000000 00000000 00000000 70: 00000000 00000000 00000000 00000000 80: 00000000 00000000 00000000 01000000 90: 00000000 00000000 00000000 00000000 Cardbus Socket registers: 00: f000ef6f: f000ef6f: f000e2c3: f000ef6f: 10: f000ef6f: f000ff54: f000e140: f000ef6f: ExCa registers: 00: 13 88 f5 5a 72 d0 80 e1 3f 74 c8 fa 66 8b 46 08 10: 52 66 0f b6 d9 66 31 d2 66 f7 f3 88 eb 88 d5 43 20: 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03 00 00 fb 77 30: a2 86 c4 c0 c8 02 08 e8 40 91 88 fe 28 e0 8a 66 isa0: on motherboard isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices fdc0: at port 0x3f0-0x3f7 irq 6 drq 2 on isa0 fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: at port 0x60-0x6f on isa0 atkbd0: irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000 psm0: irq 12 on atkbdc0 psm0: model GlidePoint, device ID 0-00, 2 buttons vga0: at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: on isa0 sc0: fb0 kbd0 pcic: polling, can't alloc 0 pcic: polling, can't alloc 0 pcic0: on isa0 pccard0: on pcic0 pccard1: on pcic0 sio0: irq maps: 0x41 0x51 0x51 0x51 sio0 at port 0x3f8-0x3ff irq 4 drq 0 flags 0x30 on isa0 sio0: type 16550A, console sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: irq maps: 0x41 0x41 0x41 0x41 sio1: probe failed test(s): 0 1 2 4 sio2: not probed (disabled) sio3: not probed (disabled) ppc: parallel port found at 0x378 ppc: chipset forced to generic ppc0: SPP ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode plip: irq 7 plip0: on ppbus 0 bpf: lp0 attached lpt0: on ppbus 0 lpt0: Interrupt-driven port ppi0: on ppbus 0 vpo0: can't connect to the drive imm0: (disconnect) s1=0x38 s2=0x38, s3=0x38 imm0: (connect) s1=0x38 s2=0x38, s3=0x38 imm0: can't connect to the drive mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) isa_probe_children: probing PnP devices BIOS Geometries: 0:020cfe3f 0..524=525 cylinders, 0..254=255 heads, 1..63=63 sectors 0 accounted for Device configuration finished. bpf: lo0 attached ata0-master: success setting up WDMA2 mode on generic chip ad0: piomode=4 dmamode=2 udmamode=2 cblid=0 ad0: ATA-4 disk at ata0 as master ad0: 4126MB (8452080 sectors), 8944 cyls, 15 heads, 63 S/T, 512 B/S ad0: 16 secs/int, 1 depth queue, DMA Creating DISK ad0 Creating DISK wd0 ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1 acd0: CDROM drive at ata1 as master acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO acd0: Reads: CD-R, CD-RW, CD-DA stream, packet acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray acd0: Medium: no/blank disc inside, unlocked Mounting root from ufs:/dev/ad0s2a ad0: ad_timeout: lost disk contact - resetting ata0: resetting devices .. ata0: mask=01 status0=50 status1=00 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message