Date: Wed, 22 Feb 2012 18:22:47 +0100 From: Hans Petter Selasky <hselasky@c2i.net> To: freebsd-usb@freebsd.org Subject: Re: fantec db 229 U3 Message-ID: <201202221822.47206.hselasky@c2i.net> In-Reply-To: <1329914180.4f44e14401943@gpo.cellcontainer.com> References: <1329914180.4f44e14401943@gpo.cellcontainer.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wednesday 22 February 2012 13:36:20 zulu wrote: > Hi, > > I can't use my external HDD attached to my laptop. The drive enclosure > is a Fantec db 229 U3 case (USB3). My laptop has only USB2 ports. > > I have tested this with both FreeBSD 9.0 RELEASE and FreeBSD 9 STABLE > - same issues. > > Tested with linux too on the same hardware and it is working fine. The > manual which came with the drive enclosure states Linux, Mac OSX and > Windows support. > > Can someone please point me to the right direction? I have included > some dumps bellow. > > Many thanks, > > Peter > > dmesg: > > usb_alloc_device: set address 2 failed (USB_ERR_STALLED, ignored) > > usbd_setup_device_desc: getting device descriptor at addr 2 failed, > USB_ERR_STALLED > usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED, > ignored) > usbd_setup_device_desc: getting device descriptor at addr 2 failed, > USB_ERR_STALLED > usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_STALLED, > ignored) > usbd_setup_device_desc: getting device descriptor at addr 2 failed, > USB_ERR_STALLED > ugen1.2: at usbus1 (disconnected) > > uhub_reattach_port: could not allocate new device > > usbconfig output: > > ugen0.1: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE > ugen1.1: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE > ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE > ugen3.1: at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE > ugen4.1: at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE > ugen5.1: at usbus5, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE > ugen6.1: at usbus6, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE > ugen0.2: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON > ugen0.3: at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON > ugen4.2: at usbus4, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON > > pciconf: > > uhci2@pci0:0:29:0:class=0x0c0300 card=0x20aa17aa chip=0x28308086 > rev=0x03 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801H (ICH8 Family) USB UHCI Controller' > class = serial bus > subclass = USB > bar [20] = type I/O Port, range 32, base 0x18a0, size 32, enabled > uhci3@pci0:0:29:1:class=0x0c0300 card=0x20aa17aa chip=0x28318086 > rev=0x03 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801H (ICH8 Family) USB UHCI Controller' > class = serial bus > subclass = USB > bar [20] = type I/O Port, range 32, base 0x18c0, size 32, enabled > uhci4@pci0:0:29:2:class=0x0c0300 card=0x20aa17aa chip=0x28328086 > rev=0x03 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801H (ICH8 Family) USB UHCI Controller' > class = serial bus > subclass = USB > bar [20] = type I/O Port, range 32, base 0x18e0, size 32, enabled > ehci1@pci0:0:29:7:class=0x0c0320 card=0x20ab17aa chip=0x28368086 > rev=0x03 hdr=0x00 > vendor = 'Intel Corporation' > device = '82801H (ICH8 Family) USB2 EHCI Controller' > class = serial bus > subclass = USB > bar [10] = type Memory, range 32, base 0xfe227000, size 1024, enabled > cap 01[50] = powerspec 2 supports D0 D3 current D0 > cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14 > Have you tried to kldload xhci? --HPS
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201202221822.47206.hselasky>