From owner-freebsd-stable Wed Aug 15 14:21:17 2001 Delivered-To: freebsd-stable@freebsd.org Received: from shumai.marcuscom.com (rdu26-228-058.nc.rr.com [66.26.228.58]) by hub.freebsd.org (Postfix) with ESMTP id 8250A37B405 for ; Wed, 15 Aug 2001 14:20:52 -0700 (PDT) (envelope-from marcus@marcuscom.com) Received: from localhost (marcus@localhost) by shumai.marcuscom.com (8.11.3/8.11.3) with ESMTP id f7FLKcJ73801; Wed, 15 Aug 2001 17:20:38 -0400 (EDT) (envelope-from marcus@marcuscom.com) X-Authentication-Warning: shumai.marcuscom.com: marcus owned process doing -bs Date: Wed, 15 Aug 2001 17:20:38 -0400 (EDT) From: Joe Clarke To: Mike Hogsett Cc: Mike Tancsa , Subject: Re: VLAN's In-Reply-To: <200108151658.f7FGwOC04876@glob.csl.sri.com> Message-ID: <20010815171921.T73750-100000@shumai.marcuscom.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: owner-freebsd-stable@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.ORG You need to be using a certain blade on the 5000 series switches to support 802.1Q VLANs. I think the WS-X5225R card can do this. If that's the case, set your encap to dot1q: set trunk on dot1q Joe Clarke On Wed, 15 Aug 2001, Mike Hogsett wrote: > > Thanks this is very helpful. I have been banging on it this morning. > I am using a Cisco Cat 5000 series swtich. Which trunk type should I > be using? I have tried both "isl" and "dot1q" and neither are working > at the moment... > > Thanks again, > > - Mike > > > At 04:18 PM 8/14/2001 -0700, Mike Hogsett wrote: > > > > >I have been reading and searching online and at FreeBSD.org for > > >information regarding VLAN's and FreeBSD. What I have found looks > > >promising. From the posts I found in various mail archives at > > >FreeBSD.org it would appear that many people have been using a patch > > >to "fix" the VLAN code for their systems. This patch appears to be > > >for 4.2. Is this patch still required for 4.3-STABLE systems? > > > > from a recent copy of STABLE, > > > > man 4 vlan shows.... > > > > The NICs that support oversized frames are as follows: > > de(4) requires defining BIG_PACKET in the > > /usr/src/sys/pci/if_de.c source file and rebuilding the > > kernel. The hack works only for the 21041, 21140, and > > 21140A chips. > > fxp(4) supports long frames for the vlan natively. > > tl(4) does support long frames. > > tx(4) may begin supporting long frames soon. > > xl(4) supports long frames only if the card is built on a newer > > chip (Cyclone and above). > > Note: Except for fxp(4), none of the above drivers inform the vlan driv > > er > > about their support for long frames. Just fix the MTU of a vlan inter- > > face if it appears to be lower that 1500 bytes after attaching the vlan > > to a parent interface that is known to support long frames. > > > > > > I have used the fxp card with good results. The only annoying thing is that > > I see a lot of run frame errors on the switch. I dont see any performance > > hit, but its there none the less. e.g. > > > > ifconfig vlan0 192.168.1.1 netmask 255.255.255.252 vlan 123 vlandev fxp0 > > mtu 1500 up > > > > is all you need. I have a box with a 13 of these interfaces and it does > > what I want with about 20Mb/s throughput. > > > > ---Mike > > > > > > > > > > >Also, does FreeBSD (4.3-STABLE) support Cisco Etherchannel? If so, > > >can I bond two interfaces together then setup VLANs on the logical > > >bonded interface? > > > > > > - Michael Hogsett > > > > > > > > > > > > > > > > > > > > >To Unsubscribe: send mail to majordomo@FreeBSD.org > > >with "unsubscribe freebsd-stable" in the body of the message > > > > -------------------------------------------------------------------- > > Mike Tancsa, tel +1 519 651 3400 > > Network Administration, mike@sentex.net > > Sentex Communications www.sentex.net > > Cambridge, Ontario Canada www.sentex.net/mike > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-stable" in the body of the message > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message