Date: Sat, 19 May 2001 11:22:46 -0700 (PDT) From: John Polstra <jdp@polstra.com> To: Warner Losh <imp@harmony.village.org> Cc: current@FreeBSD.ORG Subject: Re: GENERIC kernel hangs at boot (uhci-related) Message-ID: <XFMail.010519112246.jdp@polstra.com> In-Reply-To: <200105180404.f4I44bE07665@harmony.village.org>
next in thread | previous in thread | raw e-mail | index | archive | help
This message is in MIME format
--_=XFMail.1.3.p0.FreeBSD:010519112246:306=_
Content-Type: text/plain; charset=us-ascii
I have some more information about this now. There is a BIOS knob
"USB IRQ" which can be set to Disabled or Enabled. If it is Disabled,
the hangs occur as I described. If it is Enabled, everything works
fine. I think it ought to boot in either case (-4.x does). I am not
actually using the USB ports, so it seems silly to tie up an interrupt
for them.
PNP OS is set to "no" in the BIOS, by the way.
I hooked up a serial console and grabbed the verbose boot messages
from both cases. They are attached. "dmesg.bad" is from the case that
hangs, and "dmesg.good" is from the case that doesn't. Do a diff
between the two and you'll see a few interrupt-related things that
look interesting. The kernel config file "TEST" is attached also,
though apparently all that matters is that device uhci is configured
in.
I have a strong suspicion that backing out "sys/pci/uhci_pci.c"
revision 1.32 will make this problem go away. I'll test that next.
Does this help sufficiently, or do I still need to dig into it with
DDB and the golden paper clip?
John
--_=XFMail.1.3.p0.FreeBSD:010519112246:306=_
Content-Disposition: attachment; filename="dmesg.bad"
Content-Transfer-Encoding: 7bit
Content-Type: text/plain; charset=us-ascii; name=dmesg.bad; SizeOnDisk=13731
SMAP type=01 base=00000000 00000000 len=00000000 0009fc00
SMAP type=02 base=00000000 0009fc00 len=00000000 00000400
SMAP type=02 base=00000000 000f0000 len=00000000 00010000
SMAP type=01 base=00000000 00100000 len=00000000 07efd000
SMAP type=03 base=00000000 07ffd000 len=00000000 00002000
SMAP type=04 base=00000000 07fff000 len=00000000 00001000
SMAP type=02 base=00000000 ffff0000 len=00000000 00010000
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #1: Sat May 19 10:13:15 PDT 2001
jdp@blake.polstra.com:/a/home/jdp/checkouts/sys/compile/TEST
Calibrating clock(s) ... TSC clock: 400901111 Hz, i8254 clock: 1193158 Hz
Timecounter "i8254" frequency 1193158 Hz
Timecounter "TSC" frequency 400901111 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (400.90-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x653 Stepping = 3
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PA
T,PSE36,MMX,FXSR>
real memory = 134205440 (131060K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00405000 - 0x07ff4fff, 129957888 bytes (31728 pages)
avail memory = 126656512 (123688K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f9ce0
bios32: Entry = 0xf0520 (c00f0520) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x720
pnpbios: Found PnP BIOS data at 0xc00fd190
pnpbios: Entry = f0000:d1c0 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
Preloaded elf kernel "kernel.test" at 0xc03df000.
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
Using $PIR table, 7 entries at 0xc00f0d10
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: physical bus=0
map[10]: type 3, range 32, base e4000000, size 26, enabled
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=4, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
map[20]: type 4, range 32, base 0000d800, size 4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=4, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
map[20]: type 4, range 32, base 0000d400, size 5, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=4, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
intpin=d, irq=255
map[90]: type 4, range 32, base 0000e800, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=4, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
map[10]: type 4, range 32, base 0000d000, size 8, enabled
map[14]: type 1, range 64, base e0000000, size 12, enabled
found-> vendor=0x9005, dev=0x001f, revid=0x00
bus=0, slot=6, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=5
powerspec 1 supports D0 D3 current D0
map[10]: type 1, range 32, base df800000, size 12, enabled
map[14]: type 4, range 32, base 0000b800, size 6, enabled
map[18]: type 1, range 32, base df000000, size 20, enabled
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=10, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xe000-0xdfff
pcib1: memory decode 0xe0800000-0xe1cfffff
pcib1: prefetched decode 0xe1f00000-0xe3ffffff
pci1: physical bus=1
map[10]: type 3, range 32, base e2000000, size 25, enabled
map[14]: type 1, range 32, base e1000000, size 14, enabled
map[18]: type 1, range 32, base e0800000, size 23, enabled
found-> vendor=0x102b, dev=0x0525, revid=0x04
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at 4.1 (no driver attached)
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f at device 4.
2 on pci0
pci_cfgintr_search: linked (63) to configured irq 10 at 0:10:0
pci_cfgintr: 0:4 INTD routed to irq 10
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> port 0xe800-0xe80f irq 9 at
device 4.3 on pci0
intpm0: I/O mapped e800
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped e400
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xd000-0xd0ff mem 0xe0000000
-0xe0000fff irq 5 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 422 instructions downloaded
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb800-0xb83f mem 0xdf000000-0xdf0f
ffff,0xdf800000-0xdf800fff irq 10 at device 10.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:90:27:a6:6e:ca
fxp0: PCI IDs: 8086 1229 8086 000c
fxp0: Chip Type: 0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 15 devices, largest 114 bytes
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x378-0x37f, size=0x8, align=0
PNP0400: adding io range 0x778-0x77f, size=0x8, align=0
PNP0400: end config
pnpbios: handle 0 device ID PNP0400 (0004d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 2 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 3 device ID PNP0501 (0105d041)
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
PNP0700: end config
pnpbios: handle 4 device ID PNP0700 (0007d041)
PNP0f13: adding irq mask 0x1000
PNP0f13: end config
pnpbios: handle 5 device ID PNP0f13 (130fd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x7ffffff, size=0x7f00000
PNP0c01: adding fixed memory32 range 0xe8000-0xeffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xd1000-0xd3fff, size=0x3000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: end config
pnpbios: handle 6 device ID PNP0c01 (010cd041)
PNP0000: adding irq mask 0x4
PNP0000: adding io range 0x20-0x21, size=0x2, align=0
PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0
PNP0000: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0000: end config
pnpbios: handle 7 device ID PNP0000 (0000d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
PNP0100: end config
pnpbios: handle 8 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
PNP0b00: end config
pnpbios: handle 9 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
PNP0303: end config
pnpbios: handle 10 device ID PNP0303 (0303d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xf0, size=0x1, align=0
PNP0c04: end config
pnpbios: handle 11 device ID PNP0c04 (040cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x80-0x90, size=0x11, align=0
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0
PNP0200: end config
pnpbios: handle 12 device ID PNP0200 (0002d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
PNP0800: end config
pnpbios: handle 13 device ID PNP0800 (0008d041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: end config
pnpbios: handle 14 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x290-0x297, size=0x8, align=0
PNP0c02: adding io range 0xe400-0xe43f, size=0x40, align=0
PNP0c02: adding io range 0xe800-0xe83f, size=0x40, align=0
PNP0c02: end config
pnpbios: handle 15 device ID PNP0c02 (020cd041)
sc-: sc0 already exists, using sc1 instead
vga-: vga0 already exists, using vga1 instead
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
ata0 failed to probe at port 0x1f0 irq 14 on isa0
ata1 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 10 00 64
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300 on isa0
ed0 failed to probe at port 0x280 iomem 0xd8000 irq 10 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0 failed to probe at port 0x300 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pcm0 failed to probe at irq 10 drq 1 on isa0
pmtimer0 failed to probe on isa0
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x61 0x71 0x61 0x61
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x61 0x69 0x61 0x61
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0 failed to probe at port 0x300 irq 10 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0 failed to probe on isa0
sc1: no video adapter is found.
sc1: <System console> failed to probe on isa0
vga1: <Generic ISA VGA> failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <PNP0400> failed to probe at port 0x378-0x37f,0x778-0x77f irq 7 on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
unknown: <PNP0f13> can't assign resources
unknown: <PNP0f13> at irq 12 on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:022afe3f 0..554=555 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
IPsec: Initialized Security Association Processing.
Waiting 2 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
--_=XFMail.1.3.p0.FreeBSD:010519112246:306=_
Content-Disposition: attachment; filename="dmesg.good"
Content-Transfer-Encoding: 7bit
Content-Type: text/plain; charset=us-ascii; name=dmesg.good; SizeOnDisk=16987
SMAP type=01 base=00000000 00000000 len=00000000 0009fc00
SMAP type=02 base=00000000 0009fc00 len=00000000 00000400
SMAP type=02 base=00000000 000f0000 len=00000000 00010000
SMAP type=01 base=00000000 00100000 len=00000000 07efd000
SMAP type=03 base=00000000 07ffd000 len=00000000 00002000
SMAP type=04 base=00000000 07fff000 len=00000000 00001000
SMAP type=02 base=00000000 ffff0000 len=00000000 00010000
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #1: Sat May 19 10:13:15 PDT 2001
jdp@blake.polstra.com:/a/home/jdp/checkouts/sys/compile/TEST
Calibrating clock(s) ... TSC clock: 400900487 Hz, i8254 clock: 1193156 Hz
Timecounter "i8254" frequency 1193156 Hz
Timecounter "TSC" frequency 400900487 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (400.90-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x653 Stepping = 3
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PA
T,PSE36,MMX,FXSR>
real memory = 134205440 (131060K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00405000 - 0x07ff4fff, 129957888 bytes (31728 pages)
avail memory = 126656512 (123688K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f9ce0
bios32: Entry = 0xf0520 (c00f0520) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x720
pnpbios: Found PnP BIOS data at 0xc00fd190
pnpbios: Entry = f0000:d1c0 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
Preloaded elf kernel "kernel.test" at 0xc03df000.
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
Using $PIR table, 7 entries at 0xc00f0d10
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: physical bus=0
map[10]: type 3, range 32, base e4000000, size 26, enabled
found-> vendor=0x8086, dev=0x7190, revid=0x03
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
found-> vendor=0x8086, dev=0x7191, revid=0x03
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
found-> vendor=0x8086, dev=0x7110, revid=0x02
bus=0, slot=4, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
map[20]: type 4, range 32, base 0000d800, size 4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
bus=0, slot=4, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
map[20]: type 4, range 32, base 0000d400, size 5, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
bus=0, slot=4, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
intpin=d, irq=5
map[90]: type 4, range 32, base 0000e800, size 4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
bus=0, slot=4, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
map[10]: type 4, range 32, base 0000d000, size 8, enabled
map[14]: type 1, range 64, base e0000000, size 12, enabled
found-> vendor=0x9005, dev=0x001f, revid=0x00
bus=0, slot=6, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=5
powerspec 1 supports D0 D3 current D0
map[10]: type 1, range 32, base df800000, size 12, enabled
map[14]: type 4, range 32, base 0000b800, size 6, enabled
map[18]: type 1, range 32, base df000000, size 20, enabled
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=10, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xe000-0xdfff
pcib1: memory decode 0xe0800000-0xe1cfffff
pcib1: prefetched decode 0xe1f00000-0xe3ffffff
pci1: physical bus=1
map[10]: type 3, range 32, base e2000000, size 25, enabled
map[14]: type 1, range 32, base e1000000, size 14, enabled
map[18]: type 1, range 32, base e0800000, size 23, enabled
found-> vendor=0x102b, dev=0x0525, revid=0x04
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at 4.1 (no driver attached)
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f irq 5 at dev
ice 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> port 0xe800-0xe80f irq 9 at
device 4.3 on pci0
intpm0: I/O mapped e800
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped e400
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xd000-0xd0ff mem 0xe0000000
-0xe0000fff irq 5 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 422 instructions downloaded
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb800-0xb83f mem 0xdf000000-0xdf0f
ffff,0xdf800000-0xdf800fff irq 10 at device 10.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:90:27:a6:6e:ca
fxp0: PCI IDs: 8086 1229 8086 000c
fxp0: Chip Type: 0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 15 devices, largest 114 bytes
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x378-0x37f, size=0x8, align=0
PNP0400: adding io range 0x778-0x77f, size=0x8, align=0
PNP0400: end config
pnpbios: handle 0 device ID PNP0400 (0004d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 2 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 3 device ID PNP0501 (0105d041)
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
PNP0700: end config
pnpbios: handle 4 device ID PNP0700 (0007d041)
PNP0f13: adding irq mask 0x1000
PNP0f13: end config
pnpbios: handle 5 device ID PNP0f13 (130fd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x7ffffff, size=0x7f00000
PNP0c01: adding fixed memory32 range 0xe8000-0xeffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xd1000-0xd3fff, size=0x3000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: end config
pnpbios: handle 6 device ID PNP0c01 (010cd041)
PNP0000: adding irq mask 0x4
PNP0000: adding io range 0x20-0x21, size=0x2, align=0
PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0
PNP0000: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0000: end config
pnpbios: handle 7 device ID PNP0000 (0000d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
PNP0100: end config
pnpbios: handle 8 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
PNP0b00: end config
pnpbios: handle 9 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
PNP0303: end config
pnpbios: handle 10 device ID PNP0303 (0303d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xf0, size=0x1, align=0
PNP0c04: end config
pnpbios: handle 11 device ID PNP0c04 (040cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x80-0x90, size=0x11, align=0
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0
PNP0200: end config
pnpbios: handle 12 device ID PNP0200 (0002d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
PNP0800: end config
pnpbios: handle 13 device ID PNP0800 (0008d041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: end config
pnpbios: handle 14 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x290-0x297, size=0x8, align=0
PNP0c02: adding io range 0xe400-0xe43f, size=0x40, align=0
PNP0c02: adding io range 0xe800-0xe83f, size=0x40, align=0
PNP0c02: end config
pnpbios: handle 15 device ID PNP0c02 (020cd041)
sc-: sc0 already exists, using sc1 instead
vga-: vga0 already exists, using vga1 instead
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
ata0 failed to probe at port 0x1f0 irq 14 on isa0
ata1 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 10 00 64
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300 on isa0
ed0 failed to probe at port 0x280 iomem 0xd8000 irq 10 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0 failed to probe at port 0x300 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pcm0 failed to probe at irq 10 drq 1 on isa0
pmtimer0 failed to probe on isa0
ppc0 failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0 failed to probe at port 0x300 irq 10 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0 failed to probe on isa0
sc1: no video adapter is found.
sc1: <System console> failed to probe on isa0
vga1: <Generic ISA VGA> failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <PNP0400> failed to probe at port 0x378-0x37f,0x778-0x77f irq 7 on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
unknown: <PNP0f13> can't assign resources
unknown: <PNP0f13> at irq 12 on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:022afe3f 0..554=555 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
IPsec: Initialized Security Association Processing.
Waiting 2 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(probe0:ahc0:0:0:0): Retrying Command
(probe1:ahc0:0:1:0): Retrying Command
(probe5:ahc0:0:5:0): Retrying Command
(probe5:ahc0:0:5:0): error 22
(probe5:ahc0:0:5:0): Unretryable Error
(ahc0:A:5:0): Sending SDTR period c, offset 7f
(ahc0:A:5:0): Received SDTR period 19, offset 10
Filtered to period 19, offset 10
ahc0: target 5 synchronous at 10.0MHz, offset = 0x10
(ahc0:A:0:0): Sending WDTR 1
(ahc0:A:0:0): Received WDTR 1 filtered to 1
ahc0: target 0 using 16bit transfers
(ahc0:A:0:0): Sending SDTR period c, offset 7f
(ahc0:A:0:0): Received SDTR period c, offset 1f
Filtered to period c, offset 1f
ahc0: target 0 synchronous at 20.0MHz, offset = 0x1f
(ahc0:A:1:0): Sending WDTR 1
(ahc0:A:1:0): Received WDTR 1 filtered to 1
ahc0: target 1 using 16bit transfers
(ahc0:A:1:0): Sending SDTR period c, offset 7f
(ahc0:A:1:0): Received SDTR period c, offset f
Filtered to period c, offset f
ahc0: target 1 synchronous at 20.0MHz, offset = 0xf
(ahc0:A:5:0): Sending SDTR period 19, offset 10
(ahc0:A:5:0): Received SDTR period 19, offset 10
Filtered to period 19, offset 10
Creating DISK cd0
Creating DISK da0
Creating DISK da1
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <IBM DNES-309170W SA30> Fixed Direct Access SCSI-3 device
pass0: Serial Number AJL2J407
pass0: 40.000MB/s transfers (20.000MHz, offset 31, 16bit), Tagged Queueing Enabl
ed
pass1 at ahc0 bus 0 target 1 lun 0
pass1: <IBM DDRS-34560W S92A> Fixed Direct Access SCSI-2 device
pass1: Serial Number RD0G6423
pass1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabl
ed
pass2 at ahc0 bus 0 target 5 lun 0
pass2: <TOSHIBA CD-ROM XM-6201TA 1030> Removable CD-ROM SCSI-2 device
pass2: 10.000MB/s transfers (10.000MHz, offset 16)
Mounting root from ufs:/dev/da0s1a
(ahc0:A:5:0): Sending SDTR period 19, offset 10
(ahc0:A:5:0): Received SDTR period 19, offset 10
Filtered to period 19, offset 10
(cd0:ahc0:0:5:0): error 6
(cd0:ahc0:0:5:0): Unretryable Error
cd0 at ahc0 bus 0 target 5 lun 0
cd0: <TOSHIBA CD-ROM XM-6201TA 1030> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da1 at ahc0 bus 0 target 1 lun 0
da1: <IBM DDRS-34560W S92A> Fixed Direct Access SCSI-2 device
da1: Serial Number RD0G6423
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DNES-309170W SA30> Fixed Direct Access SCSI-3 device
da0: Serial Number AJL2J407
da0: 40.000MB/s transfers (20.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da0: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C)
da0s1: type 0xa5, start 63, end = 12273659, size 12273597 : OK
da0s2: type 0x83, start 12273660, end = 12321854, size 48195 : OK
da0s3: type 0x5, start 12321855, end = 17912474, size 5590620 : OK
da0s5: type 0x83, start 12321918, end = 17398394, size 5076477 : OK
da0<extended>: type 0x5, start 17398395, end = 17655434, size 257040 : OK
da0s6: type 0x82, start 17398458, end = 17655434, size 256977 : OK
da0<extended>: type 0x5, start 17655435, end = 17912474, size 257040 : OK
da0s7: type 0x82, start 17655498, end = 17912474, size 256977 : OK
start_init: trying /sbin/init
Enter full pathname of shell or RETURN for /bin/sh:
#
--_=XFMail.1.3.p0.FreeBSD:010519112246:306=_
Content-Disposition: attachment; filename="TEST"
Content-Transfer-Encoding: 7bit
Content-Type: text/plain; charset=us-ascii; name=TEST; SizeOnDisk=1673
#
# BLAKE
#
machine "i386"
cpu "I686_CPU"
ident BLAKE
maxusers 32
options SOFTUPDATES
options DDB
options INVARIANTS
options INVARIANT_SUPPORT
options NMBCLUSTERS=4096
options "CLK_USE_I8254_CALIBRATION"
options CLK_USE_TSC_CALIBRATION
options INET #InterNETworking
options IPSEC #IP security
options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
options KTRACE #kernel tracing
options FFS #Berkeley Fast Filesystem
options NFS #Network Filesystem
options MSDOSFS #MSDOS Filesystem
options "CD9660" #ISO 9660 Filesystem
options "EXT2FS" #Linux ext2 filesystem
options NFS_ROOT #NFS usable as root device
options PROCFS #Process filesystem
options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!]
options SYSVSHM
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
# options _KPOSIX_VERSION=199309L
device isa
device pci
device fdc
# A single entry for any of these controllers (ncr, ahb, ahc, amd) is
# sufficient for any number of installed devices.
device ahc
options AHC_ALLOW_MEMIO
device scbus
device da
device sa
device cd
device pass
# Keyboard, mouse, display.
device atkbdc 1
device atkbd
device psm
device sc 1
device vga
device splash
device npx
device sio
device miibus
device de
device fxp
device wx
device bpf
device ether
device gzip
device loop
device pty
device random
device md
# On-board power management controller.
device smbus
device intpm
device smb
device usb
device uhci
--_=XFMail.1.3.p0.FreeBSD:010519112246:306=_--
End of MIME message
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?XFMail.010519112246.jdp>