Date: Wed, 28 Jun 2006 11:40:03 -0700 From: "Matthew Jacob" <lydianconcepts@gmail.com> To: "Olivier Nicole" <on@cs.ait.ac.th> Cc: freebsd-scsi@freebsd.org Subject: Re: Problem with SLR SCSI tape Message-ID: <7579f7fb0606281140r72643ea4s9ca63199b19ab13e@mail.gmail.com> In-Reply-To: <200606280744.k5S7iEna073729@banyan.cs.ait.ac.th> References: <200606280744.k5S7iEna073729@banyan.cs.ait.ac.th>
next in thread | previous in thread | raw e-mail | index | archive | help
ILLEGAL REQUEST? What's the eot model for the SLR? The SLR is wierd in that it tries to no be a QIC tape, but it is. Can you write to a tape *not* with amanda? As in mt -f /dev/nsa0 seteotmodel 1 mt -f /dev/nsa0 weof ? On 6/28/06, Olivier Nicole <on@cs.ait.ac.th> wrote: > Hi, > > I have had that tape drive and motherboard working hand in hand for > many years without a problem. > > Lately it started to give messages like: > > on a amlabel command: > Jun 27 13:02:10 amanda /kernel: (sa0:sym1:0:2:0): WRITE FILEMARKS. CDB: 10 0 0 0 > 2 0 > Jun 27 13:02:10 amanda /kernel: (sa0:sym1:0:2:0): ILLEGAL REQUEST asc:50,0 > Jun 27 13:02:10 amanda /kernel: (sa0:sym1:0:2:0): Write append error > Jun 27 13:02:10 amanda /kernel: (sa0:sym1:0:2:0): failed to write terminating fi > lemark(s) > Jun 27 13:02:10 amanda /kernel: (sa0:sym1:0:2:0): tape is now frozen- use an OFF > LINE, REWIND or MTEOM command to clear this state. > > > Jun 27 13:03:18 amanda /kernel: (sa0:sym1:0:2:0): ERASE. CDB: 19 1 0 0 0 0 > Jun 27 13:03:18 amanda /kernel: (sa0:sym1:0:2:0): ILLEGAL REQUEST asc:2c,0 > Jun 27 13:03:18 amanda /kernel: (sa0:sym1:0:2:0): Command sequence error > > on a dd command: > Jun 28 13:48:04 amanda /kernel: (sa0:sym1:0:2:0): extraneous data discarded. > Jun 28 13:48:04 amanda /kernel: (sa0:sym1:0:2:0): COMMAND FAILED (87 0 1). > > But at same time I can do a tar without problem, I could write quite > some amount of data during a backup at night... > > Error are consistant whatever new or old tape I use in the drive. > > Drive is SLR 100 from Tandberg > sa0 at sym1 bus 0 target 2 lun 0 > sa0: <TANDBERG SLR100 0402> Removable Sequential Access SCSI-2 device > sa0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit) > > SCSI adapter is Symbios > sym1: <896> port 0xb000-0xb0ff mem 0xf8000000-0xf8001fff,0xf8800000-0xf88003ff irq 10 at device 5.1 on pci1 > sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking > sym1: open drain IRQ line driver, using on-chip SRAM > sym1: using LOAD/STORE-based firmware. > sym1: handling phase mismatch from SCRIPTS. > > Nothing has been changed in hardware and operating system lately. > > Any help or direction for diagnostic is warmly welcome > > Bests, > > Olivier > > _______________________________________________ > freebsd-scsi@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-scsi > To unsubscribe, send any mail to "freebsd-scsi-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7579f7fb0606281140r72643ea4s9ca63199b19ab13e>