Date: Thu, 8 Jul 1999 12:17:14 +0200 From: Martin Kiebacher <mwk@landshut.org> To: freebsd-mobile@freebsd.org Subject: problems with GENIUS ME 3000 II SE Message-ID: <99070812214401.00450@balu>
next in thread | raw e-mail | index | archive | help
Hello,
i'm running FreeBSD 3.1 with PAO 19990518 on my Toshiba Satellite
2520CDT. I get these messageses when i use my Genius ME 3000 II SE Card:
: Card "PCMCIA"("PCMCIA-ETHERNET-CARD") [UE2216] [R02] matched
"PCMCIA"("PCMCIA-ETHERNET-CARD") [(null)] [(null)]
: Ether=ff:ff:ff:ff:ff:ff
: Invalid MAC address. Check "ether" field of "PCMCIA"("PCMCIA-ETHERNET-
CARD") [(null)] [(null)]
and ifconfig prints:
interface ed0 does not exist
I don't know what is needed to solve the problem. Here i have added the
output of pccardc dumpcis:
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: dc 00 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 100nS, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 49 00 ff
Attribute memory device information:
Device number 1, type EEPROM, WPS = ON
Speed = 250nS, Memory block size = 512b, 1 units
Tuple #3, code = 0x20 (Manufacturer ID), length = 6
000: bf 01 16 22 e3 d2
PCMCIA ID = 0x1bf, OEM ID = 0x2216
Tuple #4, code = 0x15 (Version 1 info), length = 42
000: 04 01 50 43 4d 43 49 41 00 50 43 4d 43 49 41 2d
010: 45 54 48 45 52 4e 45 54 2d 43 41 52 44 00 55 45
020: 32 32 31 36 00 52 30 32 00 ff
Version = 4.1, Manuf = [PCMCIA], card vers = [PCMCIA-ETHERNET-CARD]
Addit. info = [UE2216],[R02]
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 24 f8 03 03
Reg len = 2, config register addr = 0x3f8, last config = 0x24
Registers: XX------
Tuple #6, code = 0x1b (Configuration entry), length = 17
000: e0 81 1d 3f 55 4d 5d 06 86 46 26 fc 24 65 30 ff
010: ff
Config index = 0x20(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 1 x 100mA
Max current average over 1 second: 1 x 100mA, ext = 0x46
Max current average over 10 ms: 2 x 100mA
Wait scale Speed = 1.5 x 10 us
Card decodes 5 address lines, full 8/16 Bit I/O
IRQ modes: Level
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 20 08 ca 60 00 03 1f
Config index = 0x20
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x300 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 21 08 ca 60 20 03 1f
Config index = 0x21
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 22 08 ca 60 40 03 1f
Config index = 0x22
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 23 08 ca 60 60 03 1f
Config index = 0x23
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #11, code = 0x14 (No link), length = 0
Tuple #12, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #13, code = 0xff (Terminator), length = 0
2 slots found
-my kernel configuration:
#
machine "i386"
#cpu "I386_CPU"
#cpu "I486_CPU"
cpu "I586_CPU"
#cpu "I686_CPU"
ident PAOMK
maxusers 10
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, "NFS" req'ed
options MFS #Memory Filesystem
options MFS_ROOT #MFS usable as root device, "MFS" req'ed
options MSDOSFS #MSDOS Filesystem
options "CD9660" #ISO 9660 Filesystem
options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed
options PROCFS #Process filesystem
options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device
options UCONSOLE #Allow users to grab the console
options FAILSAFE #Be conservative
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
# If your laptop have not had Windoze95-Ready BIOS, please update it.
# Such old BIOS'es sometimes have critical bugs at 32-bit protected
# mode APM BIOS interface (which have not used by Windoze 3.1).
# PC-card suspend/resume support (experimental)
#options APM_PCCARD_RESUME
options PCIC_RESUME_RESET
# Keep power for serial cards when the system suspends
# (If your machine hangs up when you try to suspend the system with
# FAX/Modem PCMCIA card, uncomment this option).
#options SIO_SUSP_KEEP_PWR
# Detach SCSI devices when the SCSI card is removed
#options SCSI_DETACH
# Detach ATAPI devices when the ATA card is removed
#options ATAPI_DETACH
# Japanese version of WaveLAN PCMCIA uses 2.4GHz band instead of 915MHz
# band that US version uses. If you want to use Japanese version of
# WaveLAN, uncomment this line, or edit the corresponding config entry
# of /etc/pccard.conf.
#options "WAVELAN_PCMCIA_24"
# Suspend the system when the battery status is "Low"
#options "APM_BATT_LOW_SUSPEND"
# If you want to use NTP on laptop machines, uncomment the following
# option. Current APM implementation affects NTP client.
#options "APM_NO_CLOCK_ADJUST"
# Some X-servers cannot survive suspend/resume on laptop.
# This option kicks her when the system is resumed from suspended mode.
options SYSCONS_VTY_RESUME
config kernel root on wd0
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
controller isa0
#controller eisa0
controller pci0
# Dont remove these two lines!
pseudo-device card 1
# You must use "flags 0x1" when you don't hear any negotiation noise(?)
# if you use modem card, or pccardd doesn't read cis tuple, tell you
# 'No card in database for"(null)"("(null)")' in case of Cirrus Logic's
# pcic is your PC.
#device pcic0 at isa? port 0x3e0 flags 0x1 irq 11
device pcic0 at isa? port 0x3e0 irq 11
device pcic0 at isa? port 0x3e4 irq 11
#device pcic1 at isa? port 0x3e2 # for HiNote Ultra II
#device pcic1 at isa? port 0x3e4 # for Chandra II
controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2
disk fd0 at fdc0 drive 0
disk fd1 at fdc0 drive 1
controller fdc1 at isa? disable port "IO_YEFDC" bio irq 6
disk fd2 at fdc1 drive 0
disk fd3 at fdc1 drive 1
options FDC_YE
#options "CMD640" # work around CMD640 chip deficiency
controller wdc0 at isa? port "IO_WD1" bio irq 14
disk wd0 at wdc0 drive 0
disk wd1 at wdc0 drive 1
controller wdc1 at isa? port "IO_WD2" bio irq 15
disk wd2 at wdc1 drive 0
disk wd3 at wdc1 drive 1
controller wdc2 at isa? disable port "IO_WD2" bio irq 15
disk wd4 at wdc2 drive 0
disk wd5 at wdc1 drive 1
controller wdc3 at isa? disable port "IO_WD2" bio irq 15
disk wd6 at wdc3 drive 0
disk wd7 at wdc1 drive 1
options ATAPI #Enable ATAPI support for IDE bus
options ATAPI_STATIC #Don't do it as an LKM
device acd0 #IDE CD-ROM
device wfd0 #IDE floppy (LS-120)
# A single entry for any of these controllers (ncr, ahb, ahc) is
# sufficient for any number of installed devices.
#controller ncr0
#controller ahb0
#controller ahc0
#controller isp0
#controller dpt0
#controller adv0 at isa? port ? cam irq ?
#controller adw0
#controller bt0 at isa? port ? cam irq ?
#controller aha0 at isa? port ? cam irq ?
# Don't support CAM
#controller aic0 at isa? port 0x340 bio irq 11
#controller amd0
#controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5
#controller nca0 at isa? port 0x1f88 bio irq 10
#controller nca1 at isa? port 0x350 bio irq 5
#controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000
#controller spc0 at isa? port 0x320 bio irq 11 iomem 0xd0000 flags 0x01
# Future domain and Q-logic PC-card SCSI drivers
# ported from NetBSD/pc98 (based on NetBSD 1.2)
#options SCSI_LOW # XXX: for ncv? and stg? driver
#controller ncv0 at isa? port 0x320 bio irq 5
#controller stg0 at isa? port 0x320 bio irq 5
#controller scbus0
#device da0
#device od0 #See LINT for possible `od' options.
#device sa0
#device pass0
#device cd0 #Only need one of these, the code dynamically grows
#device wt0 at isa? port 0x300 bio irq 5 drq 1
#device mcd0 at isa? port 0x300 bio irq 10
#controller matcd0 at isa? port 0x230 bio
#device scd0 at isa? port 0x230 bio
# atkbdc0 controlls both the keyboard and the PS/2 mouse
controller atkbdc0 at isa? port IO_KBD tty
device atkbd0 at isa? tty irq 1
device psm0 at isa? tty irq 12
device vga0 at isa? port ? conflicts
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? tty
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa? tty
#options XSERVER # support for X server
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Mandatory, don't remove
device npx0 at isa? port IO_NPX irq 13
#
# Laptop support (see LINT for more options)
#
device apm0 at isa? # Advanced Power Management
#options APM_BROKEN_STATCLOCK # Workaround some buggy APM BIOS
device sio0 at isa? port "IO_COM1" tty irq 4
#device sio1 at isa? port "IO_COM2" tty irq 3
#device sio2 at isa? disable port "IO_COM3" tty irq 5
#device sio3 at isa? disable port "IO_COM4" tty irq 9
#device sio4 at isa? disable port "IO_COM3" tty irq 5
#device mse0 at isa? port 0x23c tty irq 5
# Parallel port
device ppc0 at isa? port? net irq 7
controller ppbus0
device nlpt0 at ppbus?
device plip0 at ppbus?
device ppi0 at ppbus?
#controller vpo0 at ppbus?
# Order is important here due to intrusive probes, do *not* alphabetize
# this list of network interfaces until the probes have been fixed.
# Right now it appears that the ie0 must be probed before ep0. See
# revision 1.20 of this file.
device ax0
device de0
device fxp0
device mx0
device pn0
device rl0
device tl0
device tx0
device vr0
device vx0
device wb0
device xl0
device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000
device ed1 at isa? disable port 0x300 net irq 10 iomem 0xd8000
device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000
device ep0 at isa? port 0x300 net irq 10
device ep1 at isa? disable port 0x300 net irq 10
device ex0 at isa? port? net irq?
device fe0 at isa? port 0x300 net irq 10
device fe1 at isa? disable port 0x300 net irq 10
device le0 at isa? port 0x300 net irq 5 iomem 0xd0000
device lnc0 at isa? port 0x280 net irq 10 drq 0
device sn0 at isa? port 0x300 net irq 10
device sn1 at isa? disable port 0x300 net irq 10
device wlp0 at isa? port 0x300 net irq 11
device wlp1 at isa? disable port 0x300 net irq 11
device cs0 at isa? disable port 0x300 net irq ?
device cnw0 at isa? port 0x300 net irq 5
device cnw1 at isa? disable port 0x300 net irq 5
device ux0
device wi0
# do not enable ze0 and zp0 (these devices are obsolete)
##device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000
##device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000
# IBM Smart Capture PCMCIA card
#device scc0
#device scc1
# Hitachi microcomputer system Speach Synthesizer card
#device hss0
#device hss1
# PCMCIA Joystick
#device joy0 at isa? port "IO_GAME"
pseudo-device loop
pseudo-device ether
pseudo-device sl 1
# DHCP uses BPF (Berkeley Packet Filter)
pseudo-device bpfilter 4
# ijppp uses tun instead of ppp device
#pseudo-device ppp 1
pseudo-device vn 1
pseudo-device tun 1
pseudo-device pty 16
pseudo-device gzip # Exec gzipped a.out's
options DDB
# KTRACE enables the system-call tracing facility ktrace(2).
# This adds 4 KB bloat to your kernel, and slightly increases
# the costs of each syscall.
#options KTRACE #kernel tracing
# This provides support for System V shared memory.
#
options SYSVSHM
options SYSVSEM
options SYSVMSG
# USB support
#controller uhci0
#controller ohci0
#controller usb0
#
# for the moment we have to specify the priorities of the device
# drivers explicitly by the ordering in the list below. This will
# be changed in the future.
#
#device ums0
#device ukbd0
#device ulpt0
#device uhub0
#device ucom0
#device umodem0
#device hid0
#device ugen0
#
#options USB_DEBUG
#options USBVERBOSE
I don't know where i have to search for the problem.
bye
Martin
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?99070812214401.00450>