Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 08 Nov 2006 10:25:56 -0600
From:      Kevin Kramer <kramer@centtech.com>
To:        Eric Anderson <anderson@centtech.com>
Cc:        freebsd-current@freebsd.org, kramer@centtech.com
Subject:   Re: Dell Optiplex 745 / Precision 390 broadcom support
Message-ID:  <45520514.40901@centtech.com>
In-Reply-To: <45520326.8040907@centtech.com>
References:  <45520326.8040907@centtech.com>

next in thread | previous in thread | raw e-mail | index | archive | help
here is a screen shot of the crash on the Precision 390.

http://users.centtech.com/~kramer/broadcom/bge_prec390.jpg

------------------------------

Kevin Kramer
Sr. Systems Administrator
512.418.5725
Centaur Technology, Inc.
www.centtech.com



Eric Anderson wrote the following on 11/08/06 10:17:
> We've been trying to get FreeBSD (-CURRENT and -STABLE) booted on 
> these new Dells (as others have too it seems).  We have both a 
> Precision 390 and an OptiPlex 745 system.  Both boot, but neither one 
> has a supported NIC - maybe just PCI ID's?
>
> The OptiPlex 745 system has this broadcom chip (from the physical 
> markings on the chip):
> BCM5754KMLG
> UA0620 P12
> 782801 2
>
> pciconf -lv says:
> bge0@pci3:0:0:  class=0x020000 card=0x01da1028 chip=0x167a14e4 
> rev=0x02 hdr=0x00
>     vendor   = 'Broadcom Corporation'
>     class    = network
>     subclass = ethernet
>
> Snippet from dmesg shows:
> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
> pcib3:   secondary bus     3
> pcib3:   subordinate bus   3
> pcib3:   I/O decode        0xf000-0xfff
> pcib3:   memory decode     0xdfa00000-0xdfafffff
> pcib3:   prefetched decode 0xfff00000-0xfffff
> pci3: <ACPI PCI bus> on pcib3
> pci3: physical bus=3
> found-> vendor=0x14e4, dev=0x167a, revid=0x02
>         bus=3, slot=0, func=0
>         class=02-00-00, hdrtype=0x00, mfdev=0
>         cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
>         lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
>         intpin=a, irq=11
>         powerspec 3  supports D0 D3  current D0
>         MSI supports 1 message, 64 bit
>         map[10]: type 1, range 64, base dfaf0000, size 16, enabled
> pcib3: (null) requested memory range 0xdfaf0000-0xdfafffff: good
> pcib3: matched entry for 3.0.INTA
> pcib3: slot 0 INTA hardwired to IRQ 16
> bge0: <Broadcom unknown BCM5787, ASIC rev. 0xb002> mem 
> 0xdfaf0000-0xdfafffff irq 16 at device 0.0 on pci3
> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xdfaf0000
> bge0: firmware handshake timed out
> bge0: RX CPU self-diagnostics failed!
> bge0: chip initialization failed
> device_attach: bge0 attach returned 6
>
> I've attached the full dmesg output for this system.
>
> What are the next steps in figuring out support for this chip?
>
>
> Now, on the Precision 390, the kernel panics when detecting the NIC - 
> NMI memory issue, but I can't recall the error.  The physical chip in 
> this system looks like:
>
> BCM5754KMLG
> UA0617 P12
> 780856 2
>
> I can provide any additional information needed if someone would like 
> to look into it.
>
>
> Eric
>
>
>
>
> ------------------------------------------------------------------------
>
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 6.2-BETA3 #0: Mon Oct 30 22:03:42 UTC 2006
>     root@meyers.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
> Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80a67000.
> INTR: Adding local APIC 0 as a target
> ACPI APIC Table: <DELL   B8K    >
> Calibrating clock(s) ... i8254 clock: 1193189 Hz
> CLK_USE_I8254_CALIBRATION not specified - using default frequency
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Calibrating TSC clock ... TSC clock: 2660011320 Hz
> CPU: Intel(R) Core(TM)2 CPU          6700  @ 2.66GHz (2660.01-MHz K8-class CPU)
>   Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
>   Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>>
>   AMD Features=0x20000800<SYSCALL,LM>
>   AMD Features2=0x1<LAHF>
>   Cores per package: 2
> real memory  = 2137190400 (2038 MB)
> Physical memory chunk(s):
> 0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
> 0x0000000000b64000 - 0x000000007ba28fff, 2062307328 bytes (503493 pages)
> avail memory = 2052075520 (1957 MB)
> INTR: Adding local APIC 1 as a target
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
>  cpu0 (BSP): APIC ID:  0
>  cpu1 (AP): APIC ID:  1
> APIC: CPU 0 has ACPI ID 1
> APIC: CPU 1 has ACPI ID 2
> MADT: Found IO APIC ID 8, Interrupt 0 at 0xfec00000
> ioapic0: Changing APIC ID to 8
> ioapic0: Routing external 8259A's -> intpin 0
> ioapic0: intpin 0 -> ExtINT (edge, high)
> ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
> ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
> ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
> ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
> ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
> ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
> ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
> ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
> ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
> ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
> ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
> ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
> ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
> ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
> ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
> ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
> ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
> ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
> ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
> ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
> ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
> ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
> ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
> MADT: Interrupt override: source 0, irq 2
> ioapic0: Routing IRQ 0 -> intpin 2
> ioapic0: intpin 2 trigger: edge
> ioapic0: intpin 2 polarity: high
> MADT: Interrupt override: source 9, irq 9
> ioapic0: intpin 9 trigger: level
> ioapic0: intpin 9 polarity: high
> lapic: Routing NMI -> LINT1
> lapic: LINT1 trigger: level
> lapic: LINT1 polarity: high
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> lapic0: Forcing LINT1 to edge trigger
> cpu0 BSP:
>      ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>   lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff
>   timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
> wlan: <802.11 Link Layer>
> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
> null: <null device, zero device>
> random: <entropy source, Software, Yarrow>
> nfslock: pseudo-device
> kbd: new array size 4
> kbd1 at kbdmux0
> mem: <memory>
> io: <I/O>
> ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> rr232x: RocketRAID 232x controller driver v1.02 (Oct 30 2006 22:03:31)
> acpi0: <DELL B8K    > on motherboard
> ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
> acpi0: [MPSAFE]
> pci_open(1):	mode 1 addr port (0x0cf8) is 0x80001020
> pci_open(1a):	mode1res=0x80000000 (0x80000000)
> pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=29908086)
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: bus 0 dev 31 func 0
> acpi_bus_number: root bus has no _BBN, assuming 0
> AcpiOsDerivePciId: bus 0 dev 31 func 0
> acpi0: Power Button (fixed)
> ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> pci_link0: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0   11   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link0: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0   11   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link0: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link1: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0   10   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link1: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0   10   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link1: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link2: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0    3   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link2: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0    3   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link2: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link3: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link3: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link3: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link4: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0    9   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link4: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0    9   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link4: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link5: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link5: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link5: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link6: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0    9   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link6: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0    9   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link6: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link7: Links after initial probe:
> Index  IRQ  Rtd  Ref  IRQs
>     0    5   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link7: Links after initial validation:
> Index  IRQ  Rtd  Ref  IRQs
>     0    5   N     0  3 4 5 6 7 9 10 11 12 15
> pci_link7: Links after disable:
> Index  IRQ  Rtd  Ref  IRQs
>     0  255   N     0  3 4 5 6 7 9 10 11 12 15
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pci0: physical bus=0
> found->	vendor=0x8086, dev=0x2990, revid=0x02
> 	bus=0, slot=0, func=0
> 	class=06-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x8086, dev=0x2991, revid=0x02
> 	bus=0, slot=1, func=0
> 	class=06-04-00, hdrtype=0x01, mfdev=0
> 	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> pcib0: matched entry for 0.1.INTA
> pcib0: slot 1 INTA hardwired to IRQ 16
> found->	vendor=0x8086, dev=0x2992, revid=0x02
> 	bus=0, slot=2, func=0
> 	class=03-00-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0003, statreg=0x0090, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> 	powerspec 2  supports D0 D3  current D0
> 	MSI supports 1 message
> 	map[10]: type 1, range 32, base dfe00000, size 20, enabled
> 	map[18]: type 3, range 64, base c0000000, size 28, enabled
> 	map[20]: type 4, range 32, base 0000ecb8, size  3, enabled
> pcib0: matched entry for 0.2.INTA
> pcib0: slot 2 INTA hardwired to IRQ 16
> found->	vendor=0x8086, dev=0x2993, revid=0x02
> 	bus=0, slot=2, func=1
> 	class=03-80-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	powerspec 2  supports D0 D3  current D0
> 	map[10]: type 1, range 32, base dff00000, size 20, enabled
> found->	vendor=0x8086, dev=0x2834, revid=0x02
> 	bus=0, slot=26, func=0
> 	class=0c-03-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> 	map[20]: type 4, range 32, base 0000ff20, size  5, enabled
> pcib0: matched entry for 0.26.INTA
> pcib0: slot 26 INTA hardwired to IRQ 16
> found->	vendor=0x8086, dev=0x2835, revid=0x02
> 	bus=0, slot=26, func=1
> 	class=0c-03-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=b, irq=10
> 	map[20]: type 4, range 32, base 0000ff00, size  5, enabled
> pcib0: matched entry for 0.26.INTB
> pcib0: slot 26 INTB hardwired to IRQ 17
> found->	vendor=0x8086, dev=0x283a, revid=0x02
> 	bus=0, slot=26, func=7
> 	class=0c-03-20, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=c, irq=9
> 	powerspec 2  supports D0 D3  current D0
> 	map[10]: type 1, range 32, base dfdfbc00, size 10, enabled
> pcib0: matched entry for 0.26.INTC
> pcib0: slot 26 INTC hardwired to IRQ 22
> found->	vendor=0x8086, dev=0x284b, revid=0x02
> 	bus=0, slot=27, func=0
> 	class=04-03-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0106, statreg=0x0010, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> 	powerspec 2  supports D0 D3  current D0
> 	MSI supports 1 message, 64 bit
> 	map[10]: type 1, range 64, base dfdfc000, size 14, enabled
> pcib0: matched entry for 0.27.INTA
> pcib0: slot 27 INTA hardwired to IRQ 16
> found->	vendor=0x8086, dev=0x283f, revid=0x02
> 	bus=0, slot=28, func=0
> 	class=06-04-00, hdrtype=0x01, mfdev=1
> 	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> pcib0: matched entry for 0.28.INTA
> pcib0: slot 28 INTA hardwired to IRQ 16
> found->	vendor=0x8086, dev=0x2847, revid=0x02
> 	bus=0, slot=28, func=4
> 	class=06-04-00, hdrtype=0x01, mfdev=1
> 	cmdreg=0x0107, statreg=0x0010, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> pcib0: matched entry for 0.28.INTA
> pcib0: slot 28 INTA hardwired to IRQ 16
> found->	vendor=0x8086, dev=0x2830, revid=0x02
> 	bus=0, slot=29, func=0
> 	class=0c-03-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=5
> 	map[20]: type 4, range 32, base 0000ff80, size  5, enabled
> pcib0: matched entry for 0.29.INTA
> pcib0: slot 29 INTA hardwired to IRQ 23
> found->	vendor=0x8086, dev=0x2831, revid=0x02
> 	bus=0, slot=29, func=1
> 	class=0c-03-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=b, irq=10
> 	map[20]: type 4, range 32, base 0000ff60, size  5, enabled
> pcib0: matched entry for 0.29.INTB
> pcib0: slot 29 INTB hardwired to IRQ 17
> found->	vendor=0x8086, dev=0x2832, revid=0x02
> 	bus=0, slot=29, func=2
> 	class=0c-03-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=c, irq=3
> 	map[20]: type 4, range 32, base 0000ff40, size  5, enabled
> pcib0: matched entry for 0.29.INTC
> pcib0: slot 29 INTC hardwired to IRQ 18
> found->	vendor=0x8086, dev=0x2836, revid=0x02
> 	bus=0, slot=29, func=7
> 	class=0c-03-20, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=5
> 	powerspec 2  supports D0 D3  current D0
> 	map[10]: type 1, range 32, base ff980800, size 10, enabled
> pcib0: matched entry for 0.29.INTA
> pcib0: slot 29 INTA hardwired to IRQ 23
> found->	vendor=0x8086, dev=0x244e, revid=0xf2
> 	bus=0, slot=30, func=0
> 	class=06-04-01, hdrtype=0x01, mfdev=0
> 	cmdreg=0x0107, statreg=0x0010, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x8086, dev=0x2810, revid=0x02
> 	bus=0, slot=31, func=0
> 	class=06-01-00, hdrtype=0x00, mfdev=1
> 	cmdreg=0x0107, statreg=0x0210, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> found->	vendor=0x8086, dev=0x2820, revid=0x02
> 	bus=0, slot=31, func=2
> 	class=01-01-8f, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=c, irq=9
> 	powerspec 3  supports D0 D3  current D0
> 	map[10]: type 4, range 32, base 0000fe00, size  3, enabled
> 	map[14]: type 4, range 32, base 0000fe10, size  2, enabled
> 	map[18]: type 4, range 32, base 0000fe20, size  3, enabled
> 	map[1c]: type 4, range 32, base 0000fe30, size  2, enabled
> 	map[20]: type 4, range 32, base 0000fec0, size  4, enabled
> 	map[24]: type 4, range 32, base 0000ecc0, size  4, enabled
> pcib0: matched entry for 0.31.INTC
> pcib0: slot 31 INTC hardwired to IRQ 20
> found->	vendor=0x8086, dev=0x283e, revid=0x02
> 	bus=0, slot=31, func=3
> 	class=0c-05-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0103, statreg=0x0280, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=c, irq=9
> 	map[10]: type 1, range 32, base dfdfbb00, size  8, enabled
> 	map[20]: type 4, range 32, base 0000ece0, size  5, enabled
> pcib0: matched entry for 0.31.INTC
> pcib0: slot 31 INTC hardwired to IRQ 20
> found->	vendor=0x8086, dev=0x2825, revid=0x02
> 	bus=0, slot=31, func=5
> 	class=01-01-85, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0005, statreg=0x02b0, cachelnsz=0 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=c, irq=9
> 	powerspec 3  supports D0 D3  current D0
> 	map[10]: type 4, range 32, base 0000fe40, size  3, enabled
> 	map[14]: type 4, range 32, base 0000fe50, size  2, enabled
> 	map[18]: type 4, range 32, base 0000fe60, size  3, enabled
> 	map[1c]: type 4, range 32, base 0000fe70, size  2, enabled
> 	map[20]: type 4, range 32, base 0000fed0, size  4, enabled
> 	map[24]: type 4, range 32, base 0000ecd0, size  4, enabled
> pcib0: matched entry for 0.31.INTC
> pcib0: slot 31 INTC hardwired to IRQ 20
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
> pcib1:   secondary bus     1
> pcib1:   subordinate bus   1
> pcib1:   I/O decode        0xf000-0xfff
> pcib1:   memory decode     0xdfc00000-0xdfcfffff
> pcib1:   prefetched decode 0xfff00000-0xfffff
> pci1: <ACPI PCI bus> on pcib1
> pci1: physical bus=1
> pci0: <display, VGA> at device 2.0 (no driver attached)
> pci0: <display> at device 2.1 (no driver attached)
> uhci0: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 16 at device 26.0 on pci0
> uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff20
> ioapic0: routing intpin 16 (PCI IRQ 16) to vector 49
> uhci0: [GIANT-LOCKED]
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <UHCI (generic) USB controller> port 0xff00-0xff1f irq 17 at device 26.1 on pci0
> uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff00
> ioapic0: routing intpin 17 (PCI IRQ 17) to vector 50
> uhci1: [GIANT-LOCKED]
> usb1: <UHCI (generic) USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdfdfbc00-0xdfdfbfff irq 22 at device 26.7 on pci0
> ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdfdfbc00
> ioapic0: routing intpin 22 (PCI IRQ 22) to vector 51
> ehci0: [GIANT-LOCKED]
> usb2: waiting for BIOS to give up control
> usb2: EHCI version 1.0
> usb2: companion controllers, 2 ports each: usb0 usb1
> usb2: <EHCI (generic) USB 2.0 controller> on ehci0
> usb2: USB revision 2.0
> uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub2: 4 ports with 4 removable, self powered
> pci0: <multimedia> at device 27.0 (no driver attached)
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pcib2:   secondary bus     2
> pcib2:   subordinate bus   2
> pcib2:   I/O decode        0xf000-0xfff
> pcib2:   memory decode     0xdfb00000-0xdfbfffff
> pcib2:   prefetched decode 0xfff00000-0xfffff
> pci2: <ACPI PCI bus> on pcib2
> pci2: physical bus=2
> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
> pcib3:   secondary bus     3
> pcib3:   subordinate bus   3
> pcib3:   I/O decode        0xf000-0xfff
> pcib3:   memory decode     0xdfa00000-0xdfafffff
> pcib3:   prefetched decode 0xfff00000-0xfffff
> pci3: <ACPI PCI bus> on pcib3
> pci3: physical bus=3
> found->	vendor=0x14e4, dev=0x167a, revid=0x02
> 	bus=3, slot=0, func=0
> 	class=02-00-00, hdrtype=0x00, mfdev=0
> 	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
> 	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
> 	intpin=a, irq=11
> 	powerspec 3  supports D0 D3  current D0
> 	MSI supports 1 message, 64 bit
> 	map[10]: type 1, range 64, base dfaf0000, size 16, enabled
> pcib3: (null) requested memory range 0xdfaf0000-0xdfafffff: good
> pcib3: matched entry for 3.0.INTA
> pcib3: slot 0 INTA hardwired to IRQ 16
> bge0: <Broadcom unknown BCM5787, ASIC rev. 0xb002> mem 0xdfaf0000-0xdfafffff irq 16 at device 0.0 on pci3
> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xdfaf0000
> bge0: firmware handshake timed out
> bge0: RX CPU self-diagnostics failed!
> bge0: chip initialization failed
> device_attach: bge0 attach returned 6
> uhci2: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 23 at device 29.0 on pci0
> uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff80
> ioapic0: routing intpin 23 (PCI IRQ 23) to vector 52
> uhci2: [GIANT-LOCKED]
> usb3: <UHCI (generic) USB controller> on uhci2
> usb3: USB revision 1.0
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> uhci3: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 17 at device 29.1 on pci0
> uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff60
> uhci3: [GIANT-LOCKED]
> usb4: <UHCI (generic) USB controller> on uhci3
> usb4: USB revision 1.0
> uhub4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub4: 2 ports with 2 removable, self powered
> uhci4: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
> uhci4: Reserved 0x20 bytes for rid 0x20 type 4 at 0xff40
> ioapic0: routing intpin 18 (PCI IRQ 18) to vector 53
> uhci4: [GIANT-LOCKED]
> usb5: <UHCI (generic) USB controller> on uhci4
> usb5: USB revision 1.0
> uhub5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub5: 2 ports with 2 removable, self powered
> ehci1: <EHCI (generic) USB 2.0 controller> mem 0xff980800-0xff980bff irq 23 at device 29.7 on pci0
> ehci1: Reserved 0x400 bytes for rid 0x10 type 3 at 0xff980800
> ehci1: [GIANT-LOCKED]
> usb6: EHCI version 1.0
> usb6: companion controllers, 2 ports each: usb3 usb4 usb5
> usb6: <EHCI (generic) USB 2.0 controller> on ehci1
> usb6: USB revision 2.0
> uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub6: 6 ports with 6 removable, self powered
> pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pcib4:   secondary bus     4
> pcib4:   subordinate bus   4
> pcib4:   I/O decode        0xf000-0xfff
> pcib4:   memory decode     0xfff00000-0xfffff
> pcib4:   prefetched decode 0xfff00000-0xfffff
> pcib4:   Subtractively decoded bridge.
> pci4: <ACPI PCI bus> on pcib4
> pci4: physical bus=4
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH8 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf,0xecc0-0xeccf irq 20 at device 31.2 on pci0
> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfec0
> ioapic0: routing intpin 20 (PCI IRQ 20) to vector 54
> atapci0: [MPSAFE]
> ata2: <ATA channel 0> on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe00
> atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe10
> ata2: reset tp1 mask=03 ostat0=50 ostat1=00
> ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
> ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
> ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
> ata2: [MPSAFE]
> ata3: <ATA channel 1> on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe20
> atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe30
> ata3: reset tp1 mask=03 ostat0=00 ostat1=00
> ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
> ata3: [MPSAFE]
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> atapci1: <Intel ICH8 SATA300 controller> port 0xfe40-0xfe47,0xfe50-0xfe53,0xfe60-0xfe67,0xfe70-0xfe73,0xfed0-0xfedf,0xecd0-0xecdf irq 20 at device 31.5 on pci0
> atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfed0
> atapci1: [MPSAFE]
> ata4: <ATA channel 0> on atapci1
> atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xfe40
> atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xfe50
> ata4: reset tp1 mask=00 ostat0=ff ostat1=ff
> ata4: [MPSAFE]
> ata5: <ATA channel 1> on atapci1
> atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xfe60
> atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xfe70
> ata5: reset tp1 mask=00 ostat0=ff ostat1=ff
> ata5: [MPSAFE]
> ppc0: using extended I/O port range
> ppc0: ECP SPP ECP+EPP SPP
> ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/8 bytes threshold
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> plip0: bpf attached
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> ioapic0: routing intpin 7 (ISA IRQ 7) to vector 55
> sio0: irq maps: 0xca9 0xcb9 0xca9 0xca9
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> sio0: type 16550A
> ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56
> ahc_isa_probe 0: ioport 0xc00 alloc failed
> ahc_isa_probe 2: ioport 0x2c00 alloc failed
> ahc_isa_probe 5: ioport 0x5c00 alloc failed
> ahc_isa_probe 6: ioport 0x6c00 alloc failed
> ahc_isa_probe 10: ioport 0xac00 alloc failed
> ahc_isa_probe 14: ioport 0xec00 alloc failed
> ex_isa_identify()
> ppc: ppc0 already exists; skipping it
> sio: sio0 already exists; skipping it
> pnp_identify: Trying Read_Port at 203
> pnp_identify: Trying Read_Port at 243
> pnp_identify: Trying Read_Port at 283
> pnp_identify: Trying Read_Port at 2c3
> pnp_identify: Trying Read_Port at 303
> pnp_identify: Trying Read_Port at 343
> pnp_identify: Trying Read_Port at 383
> pnp_identify: Trying Read_Port at 3c3
> PNP Identify complete
> sc: sc0 already exists; skipping it
> vga: vga0 already exists; skipping it
> isa_probe_children: disabling PnP devices
> isa_probe_children: probing non-PnP devices
> orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xccfff,0xcd000-0xcefff,0xcf000-0xcffff on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> atkbd: the current kbd controller command byte 0045
> atkbd: keyboard ID 0xffffffff (1)
> atkbd: failed to reset the keyboard.
> kbd0 at atkbd0
> kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
> ioapic0: routing intpin 1 (ISA IRQ 1) to vector 57
> atkbd0: [GIANT-LOCKED]
> psm0: current command byte:0045
> psm0: failed to reset the aux device.
> fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> sio1: irq maps: 0xca9 0xca9 0xca9 0xca9
> sio1: probe failed test(s): 0 1 2 4 6 7 9
> sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
> sio2: not probed (disabled)
> sio3: not probed (disabled)
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> isa_probe_children: probing PnP devices
> ukbd0: DELL DELL USB Keyboard, rev 1.10/1.05, addr 2, iclass 3/1
> kbd2 at ukbd0
> kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
> Device configuration finished.
> Reducing kern.maxvnodes 132076 -> 100000
> linprocfs registered
> procfs registered
> lapic: Divisor 2, Frequency 133000364 hz
> Timecounter "TSC" frequency 2660011320 Hz quality -100
> Timecounters tick every 1.000 msec
> Linux ELF exec handler installed
> lo0: bpf attached
> rr232x: no controller detected.
> usb1: host controller halted
> ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
> ad4: 76293MB <WDC WD800JD-75MSA3 10.01E04> at ata2-master SATA150
> ad4: 156250000 sectors [155009C/16H/63S] 16 sectors/interrupt 1 depth queue
> GEOM: new disk ad4
> ad4: Intel check1 failed
> ad4: Adaptec check1 failed
> ad4: LSI (v3) check1 failed
> ad4: LSI (v2) check1 failed
> ad4: FreeBSD check1 failed
> ata3: reiniting channel ..
> ata3: reset tp1 mask=03 ostat0=00 ostat1=00
> ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
> ata3: reinit done ..
> ata3: reiniting channel ..
> ata3: reset tp1 mask=03 ostat0=00 ostat1=00
> ata3: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata3: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
> ata3: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
> ata3: reinit done ..
> ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire
> acd0: <TSSTcorpCD-ROM TS-L162C/DE00> CDROM drive at ata3 as master
> acd0: read 4134KB/s (4134KB/s), 96KB buffer, UDMA33
> acd0: Reads: CDR, CDRW, CDDA stream, packet
> acd0: Writes:
> acd0: Audio: play, 255 volume levels
> acd0: Mechanism: ejectable tray, unlocked
> acd0: Medium: no/blank disc
> ATA PseudoRAID loaded
> lapic1: Forcing LINT1 to edge trigger
> SMP: AP CPU #1 Launched!
> cpu1 AP:
>      ID: 0x01000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
>   lint0: 0x00010700 lint1: 0x00008400 TPR: 0x00000000 SVR: 0x000001ff
>   timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
> INTR: Assigning IRQ 1 to local APIC 0
> ioapic0: Assigning ISA IRQ 1 to local APIC 0
> INTR: Assigning IRQ 4 to local APIC 1
> ioapic0: Assigning ISA IRQ 4 to local APIC 1
> INTR: Assigning IRQ 7 to local APIC 0
> ioapic0: Assigning ISA IRQ 7 to local APIC 0
> INTR: Assigning IRQ 9 to local APIC 1
> ioapic0: Assigning ISA IRQ 9 to local APIC 1
> INTR: Assigning IRQ 16 to local APIC 0
> ioapic0: Assigning PCI IRQ 16 to local APIC 0
> INTR: Assigning IRQ 17 to local APIC 1
> ioapic0: Assigning PCI IRQ 17 to local APIC 1
> INTR: Assigning IRQ 18 to local APIC 0
> ioapic0: Assigning PCI IRQ 18 to local APIC 0
> INTR: Assigning IRQ 20 to local APIC 1
> ioapic0: Assigning PCI IRQ 20 to local APIC 1
> INTR: Assigning IRQ 22 to local APIC 0
> ioapic0: Assigning PCI IRQ 22 to local APIC 0
> INTR: Assigning IRQ 23 to local APIC 1
> ioapic0: Assigning PCI IRQ 23 to local APIC 1
> Trying to mount root from ufs:/dev/ad4s1a
> start_init: trying /sbin/init
> umass0: Seagate USB Mass Storage, rev 2.00/0.01, addr 2
> umass0: Get Max Lun not supported (STALLED)
> umass0:0:0:-1: Attached to scbus0
> pass0 at umass-sim0 bus 0 target 0 lun 0
> pass0: <ST940811 4A \\0000\\0000> Fixed Direct Access SCSI-0 device 
> pass0: 40.000MB/s transfers
> GEOM: new disk da0
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <ST940811 4A \\0000\\0000> Fixed Direct Access SCSI-0 device 
> da0: 40.000MB/s transfers
> da0: 38154MB (78140160 512 byte sectors: 255H 63S/T 4864C)
>   



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?45520514.40901>