Date: Mon, 12 Dec 2005 07:34:44 -1000 From: Robert Marella <rmarella@gmail.com> To: "Keith Bottner" <keith@barkinglizards.com> Cc: 'FreeBSD Questions' <freebsd-questions@freebsd.org> Subject: Re: Detect hardware changes Message-ID: <20051212073444.701d30a7@frankie.konav201.local> In-Reply-To: <014901c5ff28$2174bac0$1801a8c0@Stile> References: <20051209162735.574015bc@frankie.konav201.local> <014901c5ff28$2174bac0$1801a8c0@Stile>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, 12 Dec 2005 08:27:06 -0600
"Keith Bottner" <keith@barkinglizards.com> wrote:
> >=20
> > On Thu, Dec 08, 2005 at 12:02:25PM -0900, Peter Giessel wrote:
> > > On 12/8/2005 11:51, Keith Bottner seems to have typed:
> > > > skc0@pci2:9:0: class=3D0x020000 card=3D0x00241737 chip=3D0x1032173=
7=20
> > > > rev=3D0x10 hdr=3D0x00
> > > > vendor =3D 'Linksys'
> > > > device =3D 'EG1032 Gigabit Ethernet'
> > > > class =3D network
> > > > subclass =3D ethernet
> > >=20
>=20
> Ifconfig does not show skc0 but here is the output for completeness:
>=20
> xl0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> options=3D9<RXCSUM,VLAN_MTU>
> inet 192.168.1.217 netmask 0xffffff00 broadcast 192.168.1.255
> inet6 fe80::2b0:d0ff:fe16:3d30%xl0 prefixlen 64 scopeid 0x1=20
> ether 00:b0:d0:16:3d:30
> media: Ethernet autoselect (100baseTX <full-duplex>)
> status: active
> lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
> inet 127.0.0.1 netmask 0xff000000=20
> inet6 ::1 prefixlen 128=20
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2=20
>=20
> And rc.conf is:
>=20
> defaultrouter=3D"192.168.1.1"
> hostname=3D"gsdev.bltmobile.com"
> ifconfig_xl0=3D"inet 192.168.1.217 netmask 255.255.255.0"
> ifconfig_skc0=3D"inet 10.0.130.204 netmask 255.255.255.0"
> linux_enable=3D"YES"
> moused_enable=3D"YES"
> sshd_enable=3D"YES"
> usbd_enable=3D"YES"
> postgresql_enable=3D"YES"
>=20
> Anything else that I can send that will help?
>=20
> Keith
Hello Keith
I'm not sure I can be of any help. I have an older Asus board (2years)
that uses an onboard sk card. Here is the output from my machine
skc0@pci2:5:0: class=3D0x020000 card=3D0x80eb1043 chip=3D0x170010b7 rev=3D=
0x12
hdr=3D0x00 vendor =3D '3COM Corp, Networking Division'
device =3D '3C940 and 3C2000 Gigabit Ethernet PCI CODEC?'
class =3D network
subclass =3D ethernet
Mine is 3COM while yours is Linksys.
[robert@p4] ~> grep sk /var/run/dmesg.boot
skc0: <3Com 3C940 Gigabit Ethernet> port 0xd800-0xd8ff mem
0xfeafc000-0xfeafffff irq 22 at device 5.0 on pci2 skc0: 3Com Gigabit
LOM (3C940) rev. (0x1) sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:0c:6e:91:de:a6
miibus0: <MII bus> on sk0
The mii bus is shown here and unless you have removed it from your
kernel it would be automatic.
=46rom rc.conf
defaultrouter=3D"10.0.0.1"
hostname=3D"p4.konav201.local"
ifconfig_sk0=3D"inet 10.0.0.103 media 100baseTX mediaopt full-duplex
netmask 255.255.255.0"
Notice that it is sk0 _not_ skc0. AFAIK this is not your problem but it
should be changed in your rc.conf file. Except for an occasional
"watchdog" it is working fine.
I google'd for your error "rid 0x10 is ioport" but didn't see any
solutions. There was some reference to ACPI so it might be something to
try.=20
BTW I am running 6 Stable.
I hope this helps. Good luck
Robert
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051212073444.701d30a7>