From owner-freebsd-hackers Sun Mar 1 11:44:28 1998 Return-Path: Received: (from majordom@localhost) by hub.freebsd.org (8.8.8/8.8.8) id LAA21497 for freebsd-hackers-outgoing; Sun, 1 Mar 1998 11:44:28 -0800 (PST) (envelope-from owner-freebsd-hackers@FreeBSD.ORG) Received: from korin.warman.org.pl (korin.nask.waw.pl [148.81.160.10]) by hub.freebsd.org (8.8.8/8.8.8) with ESMTP id LAA21487 for ; Sun, 1 Mar 1998 11:44:21 -0800 (PST) (envelope-from abial@nask.pl) Received: from localhost (abial@localhost) by korin.warman.org.pl (8.8.8/8.8.5) with SMTP id UAA21058; Sun, 1 Mar 1998 20:46:37 +0100 (CET) X-Authentication-Warning: korin.warman.org.pl: abial owned process doing -bs Date: Sun, 1 Mar 1998 20:46:37 +0100 (CET) From: Andrzej Bialecki X-Sender: abial@korin.warman.org.pl To: Ulf Zimmermann cc: hackers@FreeBSD.ORG Subject: Re: Intel DK440LX motherboard with EtherExpress Pro/100B on board In-Reply-To: <199803011937.LAA22739@Gatekeeper.Alameda.net> Message-ID: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: owner-freebsd-hackers@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG On Sun, 1 Mar 1998, Ulf Zimmermann wrote: > > On Sun, 1 Mar 1998, Ulf Zimmermann wrote: > > > > > Hi. > > > > > > I bought an Intel DK440LX motherboard (Dual PII, Adaptec AIC-7895, Crystal > > > sound card and EtherExpress Pro/100B onboard). The fxp driver seems to > > > have a little problem: > > > > > > fxp0: rev 0x02 int a irq 11 on pci0.3.0 > > > fxp0: Ethernet address 00:a0:c9:61:68:05 > > > fxp0: warning: unsupported PHY, type = 11, addr = 1 > > > > The same warning in my case. But see below. > > > > > > > > Ifconfig shows: > > > > > > fxp0: flags=8843 mtu 1500 > > > inet 207.90.181.122 netmask 0xffffff80 broadcast 207.90.181.127 > > > ether 00:a0:c9:61:68:05 > > > media: manual > > > supported media: manual > > > > > > And you can't set anything via "ifconfig media ... mediaopt" > > > > Hmmm. Not in my case - it works perfectly. But I run -current on it, and > > you forgot to tell us your version... ;-) > > 2.2.5 RELEASE and 3.0-current SNAP 980228 Ok. You'll have to wait till tomorrow, when I'm at work and can check the exact revision of the chip and so on... Do you use it in 10Mbps or 100Mbps? I use it only in 10Mbps mode... Andrzej Bialecki ---------------------+--------------------------------------------------------- abial@warman.org.pl | if(halt_per_mth > 0) { fetch("http://www.freebsd.org") } Research & Academic | "Be open-minded, but don't let your brains to fall out." Network in Poland | All of the above (and more) is just my personal opinion. ---------------------+--------------------------------------------------------- To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message