Date: Sat, 18 Jun 2016 11:42:11 +0200 From: Emmanuel Vadot <manu@bidouilliste.com> To: Milan Obuch <freebsd-arm@dino.sk> Cc: freeBSD-arm@freebsd.org Subject: Re: any progress with OrangePi Plus / AllWinner H3 ? Message-ID: <20160618114211.f71809bd2f5a368eabca8164@bidouilliste.com> In-Reply-To: <20160618110041.e5db5c5c8378bb0822783c14@bidouilliste.com> References: <0A7A3F1D-2853-4DA4-A8A1-52C38A6ED093@cs.huji.ac.il> <20160617090156.83824237d9b1ae564bb92088@bidouilliste.com> <487C9542-1397-4CB7-837C-CD724656A0F1@cs.huji.ac.il> <20160617114018.0e70ad81@zeta.dino.sk> <0F8AAA97-99E7-4378-B6AB-F81EF45EAAC5@cs.huji.ac.il> <20160617192745.45f8a18db251547d8a01e571@bidouilliste.com> <20160617195658.0dec9f7875228ba372dadbd3@bidouilliste.com> <20160618093545.1c360555@zeta.dino.sk> <20160618094514.a83fc993b93c120fb6e014f4@bidouilliste.com> <20160618100315.12478671@zeta.dino.sk> <20160618102338.eba15ac1d427a7d3687865d8@bidouilliste.com> <20160618110041.e5db5c5c8378bb0822783c14@bidouilliste.com>
next in thread | previous in thread | raw e-mail | index | archive | help
There seems to be a problem with HIGH speed device but not every time On orangepi I successfully used : - An Optical mouse (LOW speed device) - An FDTI usb adapter (FULL speed device) - An usb 3.0 thumb drive (HIGH speed device) ugen1.2: <Logitech> at usbus1 ums0: <Logitech Optical USB Mouse, class 0/0, rev 2.00/3.40, addr 2> on usbus1 ums0: 3 buttons and [XYZ] coordinates ID=0 root@allwinner:~ # usbconfig ugen0.1: <EHCI root HUB Allwinner> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.1: <OHCI root HUB Generic> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen1.2: <Optical USB Mouse Logitech> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA) ugen1.2: <FTDI> at usbus1 uftdi0: <TTL232R-3V3> on usbus1 root@allwinner:~ # usbconfig ugen0.1: <EHCI root HUB Allwinner> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.1: <OHCI root HUB Generic> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen1.2: <TTL232R-3V3FTDI> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (90mA) ugen0.2: <Corsair> at usbus0 umass0: <Corsair Voyager Mini 3.0, class 0/0, rev 2.10/1.10, addr 2> on usbus0 umass0: SCSI over Bulk-Only; quirks = 0x8100 umass0:0:0: Attached to scbus0 da0 at umass-sim0 bus 0 scbus0 target 0 lun 0 da0: <Corsair Voyager Mini 3.0 PMAP> Removable Direct Access SPC-4 SCSI device da0: Serial Number 07083C762390FF02 da0: 40.000MB/s transfers da0: 59082MB (120999936 512 byte sectors) da0: quirks=0x2<NO_6_BYTE> GEOM: da0: the secondary GPT header is not in the last LBA. GEOM: diskid/DISK-07083C762390FF02: the secondary GPT header is not in the last LBA. root@allwinner:~ # usbconfig ugen0.1: <EHCI root HUB Allwinner> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.1: <OHCI root HUB Generic> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen0.2: <Voyager Mini 3.0 Corsair> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (300mA) But as soon as I unplug my usb thumb drive I have a hard time to attach a HIGH speed device after, I need to wait ~1 min before plugin a new device so that it works again. I also have the problem on my laptop (running ALPHA3) so it's not arm/allwinner related. On Sat, 18 Jun 2016 11:00:41 +0200 Emmanuel Vadot <manu@bidouilliste.com> wrote: > On Sat, 18 Jun 2016 10:23:38 +0200 > Emmanuel Vadot <manu@bidouilliste.com> wrote: > > > > Also, USB spams console with > > > > > > gic0: Spurious interrupt detected: last irq: 107 on CPU0 > > > usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, > > > ignored) usbd_setup_device_desc: getting device descriptor at addr 2 > > > failed, USB_ERR_IOERROR usbd_req_re_enumerate: addr=2, set address > > > failed! (USB_ERR_IOERROR, ignored) usbd_setup_device_desc: getting > > > device descriptor at addr 2 failed, USB_ERR_IOERROR > > > usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_IOERROR, > > > ignored) usbd_setup_device_desc: getting device descriptor at addr 2 > > > failed, USB_ERR_IOERROR > > > > > > (sorry mailer mangled this, but I do not expect anyone to analyze this > > > as there *are* working sources available for this... yours) > > > > > > From your tests, which devices are not working yet? Do you have any > > > plans what to work on next? > > > > I'll test USB again, it used to work at least. > > I do see the same stuff, it doesn't happened everytime thought. > I'll try to find the problem. > > -- > Emmanuel Vadot > _______________________________________________ > freebsd-arm@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-arm > To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org" -- Emmanuel Vadot
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20160618114211.f71809bd2f5a368eabca8164>