Date: Fri, 09 Oct 1998 09:45:58 +0200 From: Berthold Hoellmann <se6y095@public.uni-hamburg.de> To: aic7xxc mailing list <aic7xxx@FreeBSD.ORG> Subject: Success on ASUS P2B-S (AIC 7890) Message-ID: <361DBF36.DF4A0537@public.uni-hamburg.de>
next in thread | raw e-mail | index | archive | help
Hello,
I recently bought a new computer with a ASUS P2B-S mainboard. I have one
new and some old devices attached to it. The Quantum HDs are attached to
the wide connector, the rest is attached to the the 50-pin narrow
connector.
I'm not shure with the Quantum Model: XP32150W . I think it should
support 40 MB/s.
I can't write 120m tapes on the HP C1533A, but I had this Problem also
with the old ASUS SC200 (NCR 53c810) controller, so I think it is not
related to the AIC 7890.
The setting of "AIC7XXX_RESET_DELAY: 10" was selected after I had a
problem while writing 90m tapes on the HP C1533A. The problem
disappeared, but I'm not shure whether due to this setting.
Cheers
Berthold
>cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: VIKING 4.5 SCA Rev: 880R
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: Rev: L912
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: QUANTUM Model: XP34550W Rev: LXY4
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: MATSHITA Model: CD-ROM CR-504 Rev: ST24
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: SyQuest Model: SQ3270S Rev: 3_05
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: HP Model: C1533A Rev: 9503
Type: Sequential-Access ANSI SCSI revision: 02
>cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 5.1.0pre16/3.2.4
Compile Options:
AIC7XXX_RESET_DELAY : 10
AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
Check below to see which
devices use tagged queueing
AIC7XXX_PAGE_ENABLE : Enabled (This is no longer an option)
AIC7XXX_PROC_STATS : Enabled
Adapter Configuration:
SCSI Adapter: Adaptec AIC-7890/1 Ultra2 SCSI host adapter
Ultra2-LVD/SE Wide Controller
PCI MMAPed I/O Base: 0xe1800000
Adapter SEEPROM Config: SEEPROM found and used.
Adaptec SCSI BIOS: Enabled
IRQ: 11
SCBs: Active 1, Max Active 4,
Allocated 30, HW 32, Page 255
Interrupts: 765531
BIOS Control Word: 0x18a6
Adapter Control Word: 0x1c5e
Extended Translation: Enabled
Disconnect Enable Flags: 0xffff
Ultra Enable Flags: 0x0000
Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 8
Tagged Queue By Device array for aic7xxx host instance 0:
{255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
Actual queue depth per device for aic7xxx host instance 0:
{1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
Statistics:
(scsi0:0:0:0)
Device using Wide/Sync transfers at
40.0 MByte/sec, offset 31
Device Negotiation Settings
Period Offset Bus Width
User 010 127 1
Goal 010 127 1
Current 012 031 1
Total transfers 412440 (293532 read;118908 written)
blks(512) rd=2607829; blks(512) wr=1940824
< 512 512-1K 1-2K 2-4K 4-8K 8-16K 16-32K 32-64K 64-128K
>128K
Reads: 0 1 102264 14894 148912 18438 4126 2622
2275 0
Writes: 0 0 42041 11481 51611 4703 2318 2329
4425 0
(scsi0:0:1:0)
Device using Wide/Sync transfers at
20.0 MByte/sec, offset 15
Device Negotiation Settings
Period Offset Bus Width
User 010 127 1
Goal 010 127 1
Current 025 015 1
Total transfers 243019 (147768 read;95251 written)
blks(512) rd=998489; blks(512) wr=318812
< 512 512-1K 1-2K 2-4K 4-8K 8-16K 16-32K 32-64K 64-128K
>128K
Reads: 0 1 93406 6751 25146 19824 1081 868
691 0
Writes: 0 0 72989 18894 2765 282 73 31
217 0
(scsi0:0:2:0)
Device using Wide/Sync transfers at
40.0 MByte/sec, offset 31
Device Negotiation Settings
Period Offset Bus Width
User 010 127 1
Goal 010 127 1
Current 012 031 1
Total transfers 109156 (86061 read;23095 written)
blks(512) rd=608075; blks(512) wr=245762
< 512 512-1K 1-2K 2-4K 4-8K 8-16K 16-32K 32-64K 64-128K
>128K
Reads: 0 1 50371 1084 15820 17785 511 290
199 0
Writes: 0 0 18333 2925 691 169 106 136
735 0
(scsi0:0:4:0)
Device using Narrow/Sync transfers at
5.0 MByte/sec, offset 15
Device Negotiation Settings
Period Offset Bus Width
User 010 127 1
Goal 010 127 0
Current 050 015 0
Total transfers 131 (131 read;0 written)
blks(512) rd=3902; blks(512) wr=0
< 512 512-1K 1-2K 2-4K 4-8K 8-16K 16-32K 32-64K 64-128K
>128K
Reads: 0 6 0 72 15 2 16 6
14 0
Writes: 0 0 0 0 0 0 0 0
0 0
(scsi0:0:5:0)
Device using Narrow/Sync transfers at
5.0 MByte/sec, offset 15
Device Negotiation Settings
Period Offset Bus Width
User 010 127 1
Goal 010 127 0
Current 050 015 0
Total transfers 71 (70 read;1 written)
blks(512) rd=138; blks(512) wr=2
< 512 512-1K 1-2K 2-4K 4-8K 8-16K 16-32K 32-64K 64-128K
>128K
Reads: 0 2 68 0 0 0 0 0
0 0
Writes: 0 0 1 0 0 0 0 0
0 0
(scsi0:0:6:0)
Device using Narrow/Sync transfers at
10.0 MByte/sec, offset 8
Device Negotiation Settings
Period Offset Bus Width
User 010 127 1
Goal 010 127 0
Current 025 008 0
Total transfers 167 (0 read;167 written)
blks(512) rd=0; blks(512) wr=3340
< 512 512-1K 1-2K 2-4K 4-8K 8-16K 16-32K 32-64K 64-128K
>128K
Reads: 0 0 0 0 0 0 0 0
0 0
Writes: 0 0 0 0 0 167 0 0
0 0
--
se6y095@public.uni-hamburg.de
It is unlawful to use this email address for unsolicited ads
(USC Title 47 Sec.227). I will assess a US$500 charge for
reviewing and deleting each unsolicited ad.
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?361DBF36.DF4A0537>