Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 27 Sep 2006 16:03:36 +0300 (EEST)
From:      Dmitry Pryanishnikov <dmitry@atlantis.dp.ua>
To:        Pyun YongHyeon <pyunyh@gmail.com>
Cc:        freebsd-current@freebsd.org
Subject:   Re: Call for Marvell/SysKonnect Yukon II Gigabit Ethernet testers.
Message-ID:  <20060927155600.M40914@atlantis.atlantis.dp.ua>
In-Reply-To: <20060926002916.GA5975@cdnetworks.co.kr>
References:  <20060926002916.GA5975@cdnetworks.co.kr>

next in thread | previous in thread | raw e-mail | index | archive | help

Hello!

On Tue, 26 Sep 2006, Pyun YongHyeon wrote:
> I've written a driver for Marvell/SysKonnect Yukon II Gigabit
> Ethernet controller. It supports the following GigE adapters.
>
> The driver was tested on on-board 88E8053 PCI Express NIC and I'd

   Thank you very much! Driver works for me (i386, ASUS P5W DH Mobo with 2 
built-in 88E8053 chips):

pcib3: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci4: <ACPI PCI bus> on pcib3
mskc0: <Marvell Yukon 88E8053 Gigabit Ethernet> port 0xc800-0xc8ff mem
  0xff8fc000-0xff8fffff irq 19 at device 0.0 on pci4
msk0: <Marvell Technology Group Ltd. Yukon EC Id 0xb6 Rev 0x02> on mskc0
msk0: Ethernet address: 00:17:31:ee:d8:7f
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E1111 Gigabit PHY> on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX,
  auto
mskc0: [FAST]
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib4
mskc1: <Marvell Yukon 88E8053 Gigabit Ethernet> port 0xb800-0xb8ff mem
  0xff7fc000-0xff7fffff irq 16 at device 0.0 on pci3
msk1: <Marvell Technology Group Ltd. Yukon EC Id 0xb6 Rev 0x02> on mskc1
msk1: Ethernet address: 00:17:31:ee:d1:aa
miibus1: <MII bus> on msk1
e1000phy1: <Marvell 88E1111 Gigabit PHY> on miibus1
e1000phy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX,
  auto
mskc1: [FAST]

I'm a bit curious about the following:

test2# ifconfig -a
msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
         options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
         inet 193.108.47.148 netmask 0xfffffff8 broadcast 193.108.47.151
         ether 00:17:31:ee:d8:7f
         media: Ethernet autoselect (10baseT/UTP <full-duplex,flag0,flag1>)
         status: active

What does "flag0,flag1" mean?

And the main question is: how difficilt would it be to port this driver to
RELENG_6?


Sincerely, Dmitry
-- 
Atlantis ISP, System Administrator
e-mail:  dmitry@atlantis.dp.ua
nic-hdl: LYNX-RIPE



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20060927155600.M40914>