Date: Thu, 22 Jun 2000 16:18:25 -0500 From: "Kevin M. Dulzo" <kdulzo@caffeine.gerp.org> To: Warner Losh <imp@village.org> Cc: freebsd-stable@freebsd.org Subject: Re: Xircom PCMCIA card support Message-ID: <20000622161825.A18963@caffeine.gerp.org> In-Reply-To: <200006220212.UAA85390@harmony.village.org>; from imp@village.org on Wed, Jun 21, 2000 at 08:12:55PM -0600 References: <20000621182406.A9734@caffeine.gerp.org> <200006220212.UAA85390@harmony.village.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, Jun 21, 2000 at 08:12:55PM -0600, Warner Losh wrote:
>
> What's your pccard.conf entry for this card? The config id 35 not
> present looks bad.
>
> Warner
This is using a default out of the box /etc/defaults/pccard.conf
CVSup'd to June 20th iirc. pccard.conf shows 2 entries one modem/one ether
the modem is NOT attached either.
card "Xircom" "CreditCard Ethernet 10/100 + Modem 56"
config 0x27 "xe0" ?
insert logger -t pccard:$device -s Xircom CreditCard Modem inserted
insert /etc/pccard_ether $device
remove logger -t pccard:$device -s Xircom CreditCard Modem removed
remove /sbin/ifconfig $device delete
pccardc dumpcis output - I am sure someone will ask for this =)
Code 136 not found
Code 136 not found
code Unknown ignored
Code 138 not found
Code 138 not found
code Unknown ignored
Code 139 not found
Code 139 not found
code Unknown ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 2
000: 00 ff
Attribute memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #3, code = 0x15 (Version 1 info), length = 59
000: 05 00 58 69 72 63 6f 6d 00 43 72 65 64 69 74 43
010: 61 72 64 20 45 74 68 65 72 6e 65 74 20 31 30 2f
020: 31 30 30 20 2b 20 4d 6f 64 65 6d 20 35 36 00 43
030: 45 4d 35 36 00 31 2e 30 30 00 ff
Version = 5.0, Manuf = [Xircom], card vers = [CreditCard Ethernet 10/100 + Modem 56]
Addit. info = [CEM56],[1.00]
Tuple #4, code = 0x0 (Null tuple), length = 8
000: 24 24 fb 00 00 00 00 00
Tuple #5, code = 0x20 (Manufacturer ID), length = 5
000: 05 01 0a 11 46
PCMCIA ID = 0x105, OEM ID = 0x110a
Tuple #6, code = 0x44 (Card init date), length = 4
000: 95 b4 52 26
Tuple #7, code = 0x1a (Configuration map), length = 5
000: 01 3f 80 ff 67
Reg len = 2, config register addr = 0xff80, last config = 0x3f
Registers: XXX--XX-
Tuple #8, code = 0x1b (Configuration entry), length = 20
000: e7 c1 9d 0f 55 4d 5d 4e e0 17 17 ea 60 e8 02 07
010: f0 bc 8e 20
Config index = 0x27(default)
Interface byte = 0xc1 (I/O) +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 4.5 x 100mA
Wait scale Speed = 1.2 x 10 ms
RDY/BSY scale Speed = 1.2 x 10 ms
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x2e8 block length = 0x8
IRQ modes: Level, Pulse, Shared
IRQs: 2 3 4 5 7 9 10 11 15
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 1f 08 ea 60 e8 03 07
Config index = 0x1f
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 17 08 ea 60 f8 02 07
Config index = 0x17
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 0f 08 ea 60 f8 03 07
Config index = 0xf
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x3f8 block length = 0x8
Tuple #12, code = 0x1b (Configuration entry), length = 3
000: 3f 08 63
Config index = 0x3f
Card decodes 3 address lines, full 8/16 Bit I/O
Tuple #13, code = 0x21 (Functional ID), length = 2
000: 02 00
Serial port/modem
Tuple #14, code = 0x22 (Functional EXT), length = 4
000: 00 02 0f 5c
Serial interface extension:
16550 UART, Parity - Space,Mark,Odd,Even
Data bit - 7bit,8bit, Stop bit - 1bit,2bit
Tuple #15, code = 0x22 (Functional EXT), length = 12
000: 02 06 00 3f 1c 03 03 0f 07 00 01 b5
Data modem services available:
Tuple #16, code = 0x22 (Functional EXT), length = 8
000: 13 06 00 0b 00 02 00 b5
Fax1/modem services available:
Tuple #17, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #18, code = 0x22 (Functional EXT), length = 8
000: 04 06 00 10 a4 fb 24 24
Network node ID: 00 10 a4 fb 24 24
Tuple #19, code = 0x0 (Null tuple), length = 12
000: 39 30 30 31 48 53 46 42 32 34 32 34
Tuple #20, code = 0x0 (Null tuple), length = 4
000: 01 00 00 00
Tuple #21, code = 0x14 (No link), length = 0
Tuple #22, code = 0xff (Terminator), length = 0
2 slots found
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000622161825.A18963>