From owner-freebsd-questions Wed May 29 20:46:45 1996 Return-Path: owner-questions Received: (from root@localhost) by freefall.freebsd.org (8.7.5/8.7.3) id UAA25171 for questions-outgoing; Wed, 29 May 1996 20:46:45 -0700 (PDT) Received: from crooow.wcupa.edu (crooow.wcupa.edu [144.26.15.139]) by freefall.freebsd.org (8.7.5/8.7.3) with SMTP id UAA25142 for ; Wed, 29 May 1996 20:46:36 -0700 (PDT) Received: from westchester135.voicenet.com (westchester135.voicenet.com [207.103.17.214]) by crooow.wcupa.edu (8.6.12/8.6.12) with SMTP id XAA20819 for ; Wed, 29 May 1996 23:40:58 -0400 Received: by westchester135.voicenet.com with Microsoft Mail id <01BB4DB9.01DA68C0@westchester135.voicenet.com>; Wed, 29 May 1996 23:46:07 -0400 Message-ID: <01BB4DB9.01DA68C0@westchester135.voicenet.com> From: Peter Schwenk To: "questions@FreeBSD.org" Subject: RE: installation Date: Wed, 29 May 1996 23:45:00 -0400 MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: owner-questions@FreeBSD.org X-Loop: FreeBSD.org Precedence: bulk Hello, The Adaptec AHA2842 (Vesa Local Bus card) works fine with FreeBSD 2.1. I'm using one in a FreeBSD PC at work. It's only got one HD hooked up to it. - Peter Schwenk, Academic Computing, West Chester University of PA - pschwenk@wcupa.edu ---------- From: Doug White[SMTP:dwhite@riley-net170-164.uoregon.edu] Sent: Wednesday, May 29, 1996 7:34 AM To: Steve Chen Cc: questions@FreeBSD.org; stevec@msn.com Subject: Re: installation On Wed, 29 May 1996, Steve Chen wrote: > 80486 CPU: 66MHz > One adaptec 2840vl/2842vl SCSI controller which control my quad speed SONY > CDROM. > One EIDE controller with an 814MB hard drive. > One NE2000 compatible ethernet card. > One 14.4Kbps internal fax modern. > A Diamond Stealth SE video card with 1M memory on board. > A 15" MAGVAVOX MAGNASCAN/15 monitor with Horizontal frequency:30-66KHz and > Vertical frequence 50-11Hz. Nice box. > Because I encounter so many problems while I tried to install FreeBSD to > my system, I even get a FreeBSD 2.2 Snapshot and the booklet: Installing and > Running FreeBSD and hope if they could help me. After I read the booklet, I > have some questions. > (1) Is there any way that I can install FreeBSD to my computer with above > equipment? Should work OK. The only question is the Adaptec. I don't know if it's supported or not. > (2) If the answer is "NO", what should I do to install the FreeBSD in my > computer with the minimum cost? > If I add a extra SCSI hard drive and set it as D drive, would it be > easier to install? > Or, if, I took the EIDE controller and the 814 hard drive out of my > computer and install a SCSI hard drive, would it be helpful? My guess would be that you whould have to get a new scsi controller if that was the problem. If you don't like adaptec you could get a NCR scsi controller for $120 or so. > > (3) The original disk Geometry was: 1654 cyls/ 16 heads/ 63 sectors > During the repartition, the disk Geometry became: 827 cyls/ 32 heads/63 > sectors > And a disk space disagrement message would display while > installation. Try putting a small DOS partition on, then while installing FreeBSD delete it and put the FBSD partition over it. The DOS partition helps sysinstall determine the proper geometry. Doug White | University of Oregon Internet: dwhite@resnet.uoregon.edu | Residence Networking Assistant http://gladstone.uoregon.edu/~dwhite | Computer Science Major