Date: Fri, 08 Oct 1999 12:47:45 -0400 From: Dan Diephouse <dragon.s@ix.netcom.com> To: freebsd-hackers@freebsd.org Subject: Compaq Proliant 2500 file corruptions Message-ID: <37FE2031.DF16E119@ix.netcom.com>
next in thread | raw e-mail | index | archive | help
My school has recently acquired a Compaq Proliant 2500 and we are trying to set up FreeBSD on it. I download the 3.3 kern and mfsroot disks and replaced the kernel with a custom one that had the IDA driver included in it. Everything installed fine. Then I started working on it again and whenever I'd cvsup or download ports the files would get corrupted. Unfortunately I do not have the machine here, but it is a dual Pentium Pro with 4.3 GB scsi disks, Thunderlan net card, and a ncr scsi controller. 1. I was wondering if anyone knew of any such problems, or what other info I could provide to help figure this out. 2. There are no panics or anything. I can't seem to find an isolated case to look at. Anyone have any idea how I would go about debugging this? 3. Would I be better off running the newer driver in current? I keep tabs with whats going on in the current list, I just need a somewhat stable machine. It's only going to get light usage. Thanks for any help. Sorry this is so vauge. I'd really like you to get a dmesg. Below is the kernel config.... Dan Diephouse machine "i386" cpu "I686_CPU" ident OWL maxusers 64 options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem options NFS #Network Filesystem options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor options KTRACE #ktrace(1) syscall trace support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options DDB options DDB_UNATTENDED config kernel root on wd0 # To make an SMP kernel, the next two are needed options SMP # Symmetric MultiProcessor Kernel options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): #options NCPU=2 # number of CPUs #options NBUS=4 # number of busses #options NAPIC=1 # number of IO APICs #options NINTR=42 # number of INTs controller isa0 controller pnp0 # PnP support for ISA controller eisa0 controller pci0 # Floppy drives controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 disk fd0 at fdc0 drive 0 # IDE controller and disks #options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 #controller wdc1 at isa? port "IO_WD2" bio irq 15 #disk wd2 at wdc1 drive 0 #disk wd3 at wdc1 drive 1 # ATAPI devices #options ATAPI #Enable ATAPI support for IDE bus #options ATAPI_STATIC #Don't do it as an LKM #device acd0 #IDE CD-ROM #device wfd0 #IDE Floppy (e.g. LS-120) # SCSI Controllers # A single entry for any of these controllers (ncr, ahb, ahc) is # sufficient for any number of installed devices. controller ncr0 # NCR/Symbios Logic controller ida0 at isa? bio irq ? vector idaintr disk id0 at ida0 drive 0 disk id1 at ida0 drive 1 disk id2 at ida0 drive 2 disk id3 at ida0 drive 3 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?37FE2031.DF16E119>