Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 11 May 2012 00:54:19 +0000
From:      John <jwd@FreeBSD.org>
To:        freebsd-current@freebsd.org
Subject:   usb problems on HP DL980G7
Message-ID:  <20120511005419.GA5643@FreeBSD.org>

next in thread | raw e-mail | index | archive | help
Hi Folks,

   We've been trying to bring freebsd up on a hp dl980g7 for awhile.
Due to usb issues, we finally installed onto a revo card and
installed it into the 980. The system consistently puts out the
following messages:

usbd_ctrl_transfer_setup: could not setup default USB transfer
usb_alloc_device: set address 2 failed (USB_ERR_NOMEM, ignored)
usbd_ctrl_transfer_setup: could not setup default USB transfer
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_NOMEM
usbd_ctrl_transfer_setup: could not setup default USB transfer
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_NOMEM, ignored)
usbd_ctrl_transfer_setup: could not setup default USB transfer
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_NOMEM
usbd_ctrl_transfer_setup: could not setup default USB transfer
usbd_req_re_enumerate: addr=2, set address failed! (USB_ERR_NOMEM, ignored)
usbd_ctrl_transfer_setup: could not setup default USB transfer
usbd_setup_device_desc: getting device descriptor at addr 2 failed, USB_ERR_NOMEM
ugen0.2: <Unknown> at usbus0 (disconnected)
uhub_reattach_port: could not allocate new device

   From dmesg:

pci0: <base peripheral, interrupt controller> at device 20.0 (no driver attached)
pcib12: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci3: <ACPI PCI bus> on pcib12
pcib13: <ACPI PCI-PCI bridge> at device 28.4 on pci0
pci2: <ACPI PCI bus> on pcib13
pci2: <base peripheral> at device 0.0 (no driver attached)
pci2: <base peripheral> at device 0.2 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0x3c00-0x3c1f irq 17 at device 0.4 on pci2
usbus0 on uhci0
uhci1: <Intel 82801JI (ICH10) USB controller USB-A> port 0x1000-0x101f irq 20 at device 29.0 on pci0
device_attach: uhci1 attach returned 12
uhci1: <Intel 82801JI (ICH10) USB controller USB-B> port 0x1020-0x103f irq 23 at device 29.1 on pci0
device_attach: uhci1 attach returned 12
uhci1: <Intel 82801JI (ICH10) USB controller USB-C> port 0x1040-0x105f irq 22 at device 29.2 on pci0
device_attach: uhci1 attach returned 12
uhci1: <Intel 82801JI (ICH10) USB controller USB-F> port 0x1060-0x107f irq 23 at device 29.3 on pci0
device_attach: uhci1 attach returned 12
ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem 0xa0300000-0xa03003ff irq 20 at device 29.7 on pci0
device_attach: ehci0 attach returned 12

   Current - 10.0-CURRENT FreeBSD 10.0-CURRENT #0 r235137M

   Nothing connected to usb on this systems works.

   Full dmesg is here: http://people.freebsd.org/~jwd/dl980g7/dmesg.boot.html

   Any help is appreciated.

Thanks,
John




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20120511005419.GA5643>