From owner-freebsd-hackers Sun Mar 1 12:09:56 1998 Return-Path: Received: (from majordom@localhost) by hub.freebsd.org (8.8.8/8.8.8) id MAA26085 for freebsd-hackers-outgoing; Sun, 1 Mar 1998 12:09:56 -0800 (PST) (envelope-from owner-freebsd-hackers@FreeBSD.ORG) Received: from DNS.Lamb.net (root@DNS.Lamb.net [207.90.181.1]) by hub.freebsd.org (8.8.8/8.8.8) with ESMTP id MAA26075 for ; Sun, 1 Mar 1998 12:09:53 -0800 (PST) (envelope-from ulf@Gatekeeper.Alameda.net) Received: (from uucp@localhost) by DNS.Lamb.net (8.8.6/8.8.6) id MAA15433; Sun, 1 Mar 1998 12:10:02 -0800 (PST) Received: from gatekeeper.Alameda.net(207.90.181.2) via SMTP by DNS.Lamb.net, id smtpd015428; Sun Mar 1 12:09:58 1998 Received: (from ulf@localhost) by Gatekeeper.Alameda.net (8.8.6/8.7.6) id MAA23799; Sun, 1 Mar 1998 12:09:48 -0800 (PST) From: Ulf Zimmermann Message-Id: <199803012009.MAA23799@Gatekeeper.Alameda.net> Subject: Re: Intel DK440LX motherboard with EtherExpress Pro/100B on board In-Reply-To: from Andrzej Bialecki at "Mar 1, 98 08:46:37 pm" To: abial@nask.pl (Andrzej Bialecki) Date: Sun, 1 Mar 1998 12:09:48 -0800 (PST) Cc: ulf@Alameda.net, hackers@FreeBSD.ORG X-Mailer: ELM [version 2.4ME+ PL31 (25)] MIME-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Sender: owner-freebsd-hackers@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG > On Sun, 1 Mar 1998, Ulf Zimmermann wrote: > > > > On Sun, 1 Mar 1998, Ulf Zimmermann wrote: > > > > > > > Hi. > > > > > > > > I bought an Intel DK440LX motherboard (Dual PII, Adaptec AIC-7895, Crystal > > > > sound card and EtherExpress Pro/100B onboard). The fxp driver seems to > > > > have a little problem: > > > > > > > > fxp0: rev 0x02 int a irq 11 on pci0.3.0 > > > > fxp0: Ethernet address 00:a0:c9:61:68:05 > > > > fxp0: warning: unsupported PHY, type = 11, addr = 1 > > > > > > The same warning in my case. But see below. > > > > > > > > > > > Ifconfig shows: > > > > > > > > fxp0: flags=8843 mtu 1500 > > > > inet 207.90.181.122 netmask 0xffffff80 broadcast 207.90.181.127 > > > > ether 00:a0:c9:61:68:05 > > > > media: manual > > > > supported media: manual > > > > > > > > And you can't set anything via "ifconfig media ... mediaopt" > > > > > > Hmmm. Not in my case - it works perfectly. But I run -current on it, and > > > you forgot to tell us your version... ;-) > > > > 2.2.5 RELEASE and 3.0-current SNAP 980228 > > Ok. You'll have to wait till tomorrow, when I'm at work and can check the > exact revision of the chip and so on... Do you use it in 10Mbps or > 100Mbps? I use it only in 10Mbps mode... > > Andrzej Bialecki Hub says: Port Name Status Vlan Level Duplex Speed Type ----- ------------------ ---------- ---------- ------ ------ ----- ------------ 5/11 connected 1 normal full 100 10/100BaseTX And I just checked transfer rates, very bad. many runts. Switched hub from Full Duplex 100 to Auto and it still shows Full Duplex and 100, but much better transfer rate. Ulf. --------------------------------------------------------------------- Ulf Zimmermann, 1525 Pacific Ave., Alameda, CA-94501, #: 510-769-2936 Alameda Networks, Inc. | http://www.Alameda.net | Fax#: 510-521-5073 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message