From owner-freebsd-alpha Mon Jun 24 13: 1:17 2002 Delivered-To: freebsd-alpha@freebsd.org Received: from qescan1.qgraph.com (QESCAN1.qgraph.com [206.158.124.7]) by hub.freebsd.org (Postfix) with SMTP id F1ACD37B646 for ; Mon, 24 Jun 2002 13:00:44 -0700 (PDT) Received: from 192.168.200.28 by qescan1.qgraph.com (InterScan E-Mail VirusWall NT); Mon, 24 Jun 2002 15:00:41 -0500 Received: by sxsmtp1.qgraph.com with Internet Mail Service (5.5.2653.19) id ; Mon, 24 Jun 2002 15:00:40 -0500 Message-ID: <025596A38A894B45AFE62346A6BF47464E25E9@waexch1.qgraph.com> From: "Schroeder, Aaron" To: 'ANTOINE Pierre' , alpha@FreeBSD.ORG Subject: RE: Digital StorageWorks 300AA & HSZ40C Date: Mon, 24 Jun 2002 15:00:40 -0500 MIME-Version: 1.0 X-Mailer: Internet Mail Service (5.5.2653.19) Content-Type: text/plain; charset="iso-8859-1" Sender: owner-freebsd-alpha@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.org I look at the console output again, and your cache battery may give you fits as well. HSZ's are funny when it comes to cache batteries. If it still comes up as failed, do a 'run frutil', hit yes to replace the cache battery, then, when it prompts you to replace the battery, just hit enter, (hopefully) that will clear any battery errors. Cross your fingers. AJ -----Original Message----- From: ANTOINE Pierre [mailto:nunux@free.fr] Sent: Monday, June 24, 2002 2:28 PM To: alpha@FreeBSD.ORG Subject: Digital StorageWorks 300AA & HSZ40C Hi, My Alpha 2100A perfectly boot with FreeBSD 4.6, my problem (previous mail) was: "Put the VGA PCI card in first PCI block"! I've surf a while before founding how to configure RAID on the mylex controller, but it's finaly done. Now, I'm seeking informations about a Digital StorageWorks 300AA hooked to a PCI card: KZPSA SCSI Controller. Is this StorageWorks Arrays supported on FreeBSD ? Has anyone an StorageWorks working with his alpha server ? Can you see disks in SRM or you needs to access it via a special driver ? On the server, I can see the SCSI interface KZPSA as pkb, doing show FRU, and show CONFIG, but no disks. I've hook a serial terminal to the Digital StorageWorks 300AA, playing at 9600 bauds and get a prompt. Any command fail and suggest to do a "SHOW THIS_CONTROLLER" so i give you the result: HSZ40C>SHOW THIS_CONTROLLER Controller: HSZ40 ZG61200481 Firmware V34Z-0, Hardware A02 Not configured for dual-redundancy SCSI address 7 Time: NOT SET Host port: SCSI target(s) (0), Preferred target(s) (0) TRANSFER_RATE_REQUESTED = 10MHZ Cache: 32 megabyte write cache, version 2 Cache is INVALID. Cache containing unflushed data has been removed from this controller Battery is FAILED Unknown unflushed data in cache CACHE_FLUSH_TIMER = DEFAULT (10 seconds) CACHE_POLICY = A NOCACHE_UPS Host Functionality Mode = A This controller has an invalid cache module Invalid cache -- CLI command set reduced. Type SHOW THIS_CONTROLLER. Please- see user guide to determine corrective action HSZ40C> Thanks for your tips. ---------------- ANTOINE Pierre nunux@free.fr --------------- To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message