Date: Fri, 30 Oct 1998 07:48:14 -0500 From: David Gregory <dgregory@BudcoDM.budco.com> To: AIC7xxx@FreeBSD.ORG Subject: Re: scsi : aborting command due to timeout, commands queued exceeds queue depth, active=255 Message-ID: <3639B58D.D1A7BFDB@budco.com> References: <199810300056.QAA25214@hub.freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi,
I think I have a problem with my device driver??? Not sure, I think it just
needs tweeking at boot?? This is from the stock redhat 5.1 distribution.
Below I grep /var/log/messages for "scsi" and after that I dump my startup
messages from the
/var/log/dmesg file.
Does anyone know how to fix this??
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
>>>>> Here's just a grep from my messages in /var/log <<<<<<<<<<<<<
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
[root@mis2 log]# grep scsi messages
Oct 25 04:22:25 mis2 kernel: scsi : aborting command due to timeout : pid
106863, scsi0, channel 0, id 0, lun 0 Read (6) 0f 4a d9 06 00
Oct 27 06:39:01 mis2 kernel: scsi : aborting command due to timeout : pid
120057, scsi0, channel 0, id 0, lun 0 Read (6) 06 c9 3f 08 00
Oct 28 04:03:37 mis2 kernel: scsi : aborting command due to timeout : pid
123388, scsi0, channel 0, id 0, lun 0 Write (10) 00 00 31 80 79 00 00 02 00
Oct 28 04:03:37 mis2 kernel: scsi : aborting command due to timeout : pid
123390, scsi0, channel 0, id 0, lun 0 Write (10) 00 00 32 80 67 00 00 02 00
Oct 28 04:03:37 mis2 kernel: (scsi0:0:0:0) Commands queued exceeds queue depth,
active=255
Oct 29 21:02:51 mis2 kernel: scsi : 0 hosts.
Oct 29 21:02:51 mis2 kernel: scsi : detected total.
Oct 29 21:02:51 mis2 kernel: (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter>
found at PCI 12/0
Oct 29 21:02:51 mis2 kernel: (scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs
Oct 29 21:02:51 mis2 kernel: (scsi0) BIOS enabled, IO Port 0x6000, IRQ 11
Oct 29 21:02:51 mis2 kernel: (scsi0) IO Memory at 0xe1000000, MMAP Memory at
0x4819000
Oct 29 21:02:51 mis2 kernel: (scsi0) Resetting channel
Oct 29 21:02:51 mis2 kernel: (scsi0) Downloading sequencer code... 406
instructions downloaded
Oct 29 21:02:51 mis2 kernel: scsi0 : Adaptec AHA274x/284x/294x
(EISA/VLB/PCI-Fast SCSI) 5.0.13/3.2.4
Oct 29 21:02:51 mis2 kernel: scsi : 1 host.
Oct 29 21:02:51 mis2 kernel: (scsi0:0:-1:-1) Scanning channel for devices.
Oct 29 21:02:51 mis2 kernel: (scsi0:0:0:0) Synchronous at 5.0MHz, offset 15.
Oct 29 21:02:51 mis2 kernel: Detected scsi disk sda at scsi0, channel 0, id 0,
lun 0
Oct 29 21:02:51 mis2 kernel: (scsi0:0:4:0) Synchronous at 5.0MHz, offset 15.
Oct 29 21:02:51 mis2 kernel: Detected scsi disk sdb at scsi0, channel 0, id 4,
lun 0
Oct 29 21:02:51 mis2 kernel: (scsi0:0:6:0) Synchronous at 5.0MHz, offset 15.
Oct 29 21:02:51 mis2 kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6,
lun 0
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
>>>>> Here's a dump of my dmesg file on boot <<<<<<<<<<<<<
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
[root@mis2 log]# cat dmesg
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fb190
pcibios_init : BIOS32 Service Directory entry at 0xfb600
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb630
Probing PCI hardware.
Calibrating delay loop.. ok - 199.48 BogoMIPS
Memory: 63908k/66496k available (732k kernel code, 384k reserved, 1272k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.34 (root@porky.redhat.com) (gcc version 2.7.2.3) #1 Fri May 8
16:05:57 EDT 1998
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.07
Ramdisk driver initialized : 16 ramdisks of 4096K size
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide0: BM-DMA at 0x3000-0x3007
ide1: BM-DMA at 0x3008-0x300f
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.35 MAX_MD_DEV=4, MAX_REAL=8
scsi : 0 hosts.
scsi : detected total.
Partition check:
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
aic7xxx: Warning - detected auto-termination on controller:
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 12/0
aic7xxx: Please verify driver detected settings are correct.
aic7xxx: If not, then please properly set the device termination
aic7xxx: in the Adaptec SCSI BIOS by hitting CTRL-A when prompted
aic7xxx: during machine bootup.
aic7xxx: Cables present (Int-50 YES, Ext-50 NO)
aic7xxx: Termination Enabled
(scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 12/0
(scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs
(scsi0) BIOS enabled, IO Port 0x6000, IRQ 11
(scsi0) IO Memory at 0xe1000000, MMAP Memory at 0x4819000
(scsi0) Resetting channel
(scsi0) Downloading sequencer code... 406 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.13/3.2.4
<Adaptec AHA-294X Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:-1:-1) Scanning channel for devices.
(scsi0:0:0:0) Synchronous at 5.0MHz, offset 15.
Vendor: SEAGATE Model: ST43400N Rev: 0116
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:4:0) Synchronous at 5.0MHz, offset 15.
Vendor: FUJITSU Model: M2949S-512 Rev: 0142
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
(scsi0:0:6:0) Synchronous at 5.0MHz, offset 15.
Vendor: NEC Model: CD-ROM DRIVE:222 Rev: 3.0i
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
SCSI device sda: hdwr sector= 512 bytes. Sectors= 5688447 [2777 MB] [2.8 GB]
sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17781964 [8682 MB] [8.7 GB]
sdb: sdb1
VFS: Mounted root (ext2 filesystem) readonly.
Trying to unmount old root ... okay
Adding Swap: 128484k swap-space (priority -1)
Adding Swap: 128484k swap-space (priority -2)
Adding Swap: 128484k swap-space (priority -3)
Adding Swap: 128484k swap-space (priority -4)
[root@mis2 log]#
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3639B58D.D1A7BFDB>