Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 30 Aug 2008 21:00:35 +0200
From:      Christian Hiris <4711@chello.at>
To:        Sean Bruno <sbruno@miralink.com>
Cc:        freebsd-ports@freebsd.org
Subject:   Re: -d 3ware,0 not working with 3ware 9550(sx)
Message-ID:  <200808302100.39036.4711@chello.at>
In-Reply-To: <48B991BE.2000607@miralink.com>
References:  <48B6E216.30609@miralink.com> <200808300945.14447.4711@chello.at> <48B991BE.2000607@miralink.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Saturday 30 August 2008, Sean Bruno wrote:
> Christian Hiris wrote:
> > On Thursday 28 August 2008, Sean Bruno wrote:
> >> I sent this over to the smartmontools mailing list, but thought I would
> >> post it here in case anyone else has run into this:
> >>
> >>
> >> Using smartmontools 5.38 under FreeBSD 6/7 doesn't seem to work with the
> >> following card:
> >> twa0@pci4:12:0: class=0x010400 card=0x100313c1 chip=0x100313c1 rev=0x00
> >> hdr=0x00
> >>     vendor     = '3ware
> >> Inc.'
> >>     device     = '9550SX/9590SE Series SATA2 Raid
> >> Controller'
> >>     class      = mass
> >> storage
> >>     subclass   = RAID
> >>
> >> smartctl command output:
> >> Source # smartctl -d3ware,0
> >> /dev/da0
> >> smartctl version 5.36 [i386-portbld-freebsd6.3] Copyright (C) 2002-6
> >> Bruce Allen
> >> Home page is
> >> http://smartmontools.sourceforge.net/
> >>
> >>
> >>
> >> Unrecognized escalade_type 4 in freebsd_3ware_command_interface(disk
> >> 0)
> >> Please contact
> >> smartmontools-support@lists.sourceforge.net
> >> Unrecognized escalade_type 4 in freebsd_3ware_command_interface(disk
> >> 0)
> >> Please contact
> >> smartmontools-support@lists.sourceforge.net
> >> Smartctl: Device Read Identity Failed (not an ATA/ATAPI
> >> device)
> >>
> >>
> >>
> >> A mandatory SMART command failed: exiting. To continue, add one or more
> >> '-T per.
> >> Source #
> >
> > Try # smartctl -d3ware,0 /dev/twa0
> >                               ^^^^
> > Works here with a 9500S-8 card on FreeBSD 7.0-STABLE.
> >
> > Cheers,
> > ch
>
> Hmmm ... that didn't seem to work for me:
>
> Source # smartctl -d3ware,0 /dev/twa0
> smartctl version 5.36 [i386-portbld-freebsd6.3] Copyright (C) 2002-6
> Bruce Allen
> Home page is http://smartmontools.sourceforge.net/
>
> Command failed, ata.status=(0x00), ata.command=(0xec), ata.flags=(0x01)
> WARNING - NO DEVICE FOUND ON 3WARE CONTROLLER (disk 0)
> Smartctl: Device Read Identity Failed (not an ATA/ATAPI device)
>
> A mandatory SMART command failed: exiting. To continue, add one or more
> '-T permissive' options.
> Source # uname -a
> FreeBSD  6.4-PRERELEASE FreeBSD 6.4-PRERELEASE #0 r5811:5829: Thu Aug 28
> 11:01:38 PDT 2008
> sbruno@desdemona.office.miralink.com:/home/sbruno/work/src/ankeny/src/FreeB
>SD_RELENG6/sys/i386/compile/MIRALINK i386

Is there a HDD connected to port 0? I get something similar if I check on a 
port w/o any disk attached to:

# smartctl -d3ware,7 /dev/twa0
smartctl version 5.38 [i386-portbld-freebsd7.0] Copyright (C) 2002-8 Bruce 
Allen
Home page is http://smartmontools.sourceforge.net/

Command failed, ata.status=(0x03), ata.command=(0xec), ata.flags=(0x01)
WARNING - NO DEVICE FOUND ON 3WARE CONTROLLER (disk 7)
Smartctl: Device Read Identity Failed (not an ATA/ATAPI device)

A mandatory SMART command failed: exiting. To continue, add one or more '-T 
permissive' options.
#                          

Btw, I run version 5.38. 
Cheers,
ch

-- 
Christian Hiris <4711@chello.at> | OpenPGP KeyID 0x1A9BE943
OpenPGP-Key at hkp://wwwkeys.eu.pgp.net and http://pgp.mit.edu



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200808302100.39036.4711>