Date: Wed, 07 Mar 2007 11:10:49 -0500 From: Sam Baskinger <sbaskinger@lumeta.com> To: Ivan Voras <ivoras@fer.hr> Cc: freebsd-stable@freebsd.org Subject: Re: SMP doesn't work without ACPI? Message-ID: <45EEE409.6070106@lumeta.com> In-Reply-To: <esmjkl$33l$1@sea.gmane.org> References: <esmjkl$33l$1@sea.gmane.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Adding a datapoint: Dell 1950s exhibit similar behaviour but have 2 cores in a single physical CPU. Hope this helps the discussion along. Sam Baskinger Software Engineer Lumeta - Securing the Network in the Face of Change Ivan Voras wrote: > Continuing my problems with the IBM blade: Booting with ACPI module > enabled (btw. live boot CD with sysinstall doesn't load ACPI, but the > installed system does?) hangs the system somewhere after first USB bus > is found (booting verbose doesn't show any new lines before or after > this step). It appears to be a real hang instead of a timeout because I > left it 30 minutes and it didn't continue. > > Booting without ACPI on the other hand doesn't find all the CPU's :( > > Here's sysctl output: > >> sysctl -a | grep smp > kern.timecounter.smp_tsc: 0 > kern.smp.forward_roundrobin_enabled: 1 > kern.smp.forward_signal_enabled: 1 > kern.smp.cpus: 1 > kern.smp.disabled: 0 > kern.smp.active: 0 > kern.smp.maxcpus: 16 > > > Here's the mptable -dmesg output: > > > > =============================================================================== > > MPTable > > ------------------------------------------------------------------------------- > > MP Floating Pointer Structure: > > location: EBDA > physical address: 0x0009d140 > signature: '_MP_' > length: 16 bytes > version: 1.4 > checksum: 0xfe > mode: Virtual Wire > > ------------------------------------------------------------------------------- > > MP Config Table Header: > > physical address: 0x0009e9b0 > signature: 'PCMP' > base table length: 388 > version: 1.4 > checksum: 0x77 > OEM ID: 'IBM ENSW' > Product ID: 'LEWIS SMP ' > OEM table pointer: 0x00000000 > OEM table size: 0 > entry count: 37 > local APIC address: 0xfee00000 > extended table length: 408 > extended table checksum: 159 > > ------------------------------------------------------------------------------- > > MP Config Base Table Entries: > > -- > Processors: APIC ID Version State Family Model Step > Flags > 0 0x10 BSP, usable 15 1 2 > 0x0301 > 2 0x10 AP, usable 15 1 2 > 0x0301 > 1 0x10 AP, usable 15 1 2 > 0x0301 > 3 0x10 AP, usable 15 1 2 > 0x0301 > -- > Bus: Bus ID Type > 0 PCI > 1 PCI > 2 PCI > 3 PCI > 4 PCI > 5 PCI > 6 PCI > 7 PCI > 8 PCI > 9 ISA > -- > I/O APICs: APIC ID Version State Address > 14 0x11 usable 0xfec00000 > 13 0x11 usable 0xfec02000 > -- > I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# > INT conforms conforms 9 1 14 1 > INT conforms conforms 9 0 14 2 > INT conforms conforms 9 4 14 4 > INT conforms conforms 9 6 14 6 > INT active-hi edge 9 8 14 8 > INT conforms conforms 9 11 14 11 > INT conforms conforms 9 12 14 12 > INT conforms conforms 9 13 14 13 > INT conforms conforms 9 14 14 14 > INT conforms conforms 9 15 14 15 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 3:A 14 3 > INT conforms conforms 0 5:A 13 0 > INT conforms conforms 2 4:A 13 1 > INT conforms conforms 2 5:A 13 2 > INT conforms conforms 3 4:A 13 3 > INT conforms conforms 3 5:A 13 4 > INT conforms conforms 3 5:B 13 5 > -- > Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# > NMI conforms conforms 9 0 255 1 > ExtINT conforms conforms 9 0 255 0 > > ------------------------------------------------------------------------------- > > MP Config Extended Table Entries: > > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xa0000 > address range: 0x20000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xf8000000 > address range: 0x2000000 > -- > System Address Space > bus ID: 0 address type: prefetch address > address base: 0xf0000000 > address range: 0x8000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xea000000 > address range: 0x6000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe7000000 > address range: 0x1100000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe5000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe4000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe3000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe2000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: memory address > address base: 0xe1000000 > address range: 0x1000000 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x0 > address range: 0x3b0 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3b0 > address range: 0xc > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3bc > address range: 0x4 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3c0 > address range: 0x20 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x3e0 > address range: 0x3c20 > -- > System Address Space > bus ID: 0 address type: I/O address > address base: 0x4000 > address range: 0x1000 > -- > -- > Bus Heirarchy > bus ID: 1 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 2 bus info: 0x00 parent bus ID: 1 > -- > Bus Heirarchy > bus ID: 3 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 4 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 5 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 6 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 7 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 8 bus info: 0x00 parent bus ID: 0 > -- > Bus Heirarchy > bus ID: 9 bus info: 0x01 parent bus ID: 0 > -- > Compatibility Bus Address > bus ID: 0 address modifier: add > predefined range: 0x00000000 > -- > Compatibility Bus Address > bus ID: 0 address modifier: add > predefined range: 0x00000001 > > ------------------------------------------------------------------------------- > > dmesg output: > > Copyright (c) 1992-2007 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 6.2-STABLE #0: Wed Mar 7 15:08:28 CET 2007 > root@:/usr/obj/usr/src/sys/SMP > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Dual-Core AMD Opteron(tm) Processor 2216 HE (2400.10-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0x40f12 Stepping = 2 > > Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> > Features2=0x2001<SSE3,CX16> > AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!> > AMD Features2=0x1f<LAHF,CMP,SVM,ExtAPIC,CR8> > Cores per package: 2 > real memory = 4815060992 (4592 MB) > avail memory = 4130750464 (3939 MB) > kbd1 at kbdmux0 > ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > cpu0 on motherboard > pcib0: <Host to PCI bridge> pcibus 0 on motherboard > pci0: <PCI bus> on pcib0 > pcib1: <PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pcib2: <PCI-PCI bridge> at device 13.0 on pci1 > pci2: <PCI bus> on pcib2 > bce0: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem > 0xea000000-0xebffffff irq 5 at device 4.0 on pci2 > bce0: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz > miibus0: <MII bus> on bce0 > gentbi0: <Generic ten-bit interface> on miibus0 > gentbi0: 1000baseSX, 1000baseSX-FDX, auto > bce0: Ethernet address: 00:14:5e:6d:2d:74 > bce1: <Broadcom NetXtreme II BCM5706 1000Base-SX (A2), v0.9.6> mem > 0xec000000-0xedffffff irq 10 at device 5.0 on pci2 > bce1: ASIC ID 0x57060021; Revision (A2); PCI-X 64-bit 133MHz > miibus1: <MII bus> on bce1 > gentbi1: <Generic ten-bit interface> on miibus1 > gentbi1: 1000baseSX, 1000baseSX-FDX, auto > bce1: Ethernet address: 00:14:5e:b3:2a:38 > isab0: <PCI-ISA bridge> at device 2.2 on pci0 > isa0: <ISA bus> on isab0 > ohci0: <OHCI (generic) USB controller> port 0x3000-0x30ff mem > 0xf9fff000-0xf9ffffff irq 3 at device 3.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > ohci1: <OHCI (generic) USB controller> port 0x3100-0x31ff mem > 0xf9ffe000-0xf9ffefff irq 3 at device 3.1 on pci0 > ohci1: [GIANT-LOCKED] > usb1: OHCI version 1.0, legacy support > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> port 0x3200-0x32ff mem > 0xf9ffd000-0xf9ffdfff irq 3 at device 3.2 on pci0 > ehci0: [GIANT-LOCKED] > usb2: EHCI version 1.0 > usb2: companion controllers, 2 ports each: usb0 usb1 > usb2: <EHCI (generic) USB 2.0 controller> on ehci0 > usb2: USB revision 2.0 > uhub2: (0x1166) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub2: 4 ports with 4 removable, self powered > uhub3: vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.07, addr 2 > uhub3: multiple transaction translators > uhub3: 2 ports with 2 removable, self powered > uhub4: Cypress Semiconductor 4 Port Hub, class 9/0, rev 1.10/0.01, addr 3 > uhub4: 4 ports with 4 removable, self powered > umass0: TEAC TEAC FD-05PUB, rev 2.00/0.00, addr 4 > umass1: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 5 > umass1: Get Max Lun not supported (STALLED) > pci0: <display, VGA> at device 5.0 (no driver attached) > pcib3: <PCI-PCI bridge> at device 6.0 on pci0 > pci3: <PCI bus> on pcib3 > mpt0: <LSILogic SAS/SATA Adapter> port 0x4000-0x40ff mem > 0xe8010000-0xe8013fff,0xe8000000-0xe800ffff irq 9 at device 4.0 on pci3 > mpt0: [GIANT-LOCKED] > mpt0: MPI Version=1.5.12.0 > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > mpt0: mpt_cam_event: 0x12 > mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > pci3: <serial bus, Fibre Channel> at device 5.0 (no driver attached) > pci3: <serial bus, Fibre Channel> at device 5.1 (no driver attached) > pcib4: <PCI-PCI bridge> at device 7.0 on pci0 > pci4: <PCI bus> on pcib4 > pcib5: <PCI-PCI bridge> at device 8.0 on pci0 > pci5: <PCI bus> on pcib5 > pcib6: <PCI-PCI bridge> at device 9.0 on pci0 > pci6: <PCI bus> on pcib6 > pcib7: <PCI-PCI bridge> at device 10.0 on pci0 > pci7: <PCI bus> on pcib7 > pcib8: <PCI-PCI bridge> at device 11.0 on pci0 > pci8: <PCI bus> on pcib8 > orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > ppc0: cannot reserve I/O port range > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ukbd0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > kbd2 at ukbd0 > ums0: IBM IBM MM2, rev 1.10/0.01, addr 2, iclass 3/1 > ums0: 3 buttons and Z dir. > Timecounter "TSC" frequency 2400100239 Hz quality 800 > Timecounters tick every 1.000 msec > da1 at mpt0 bus 0 target 0 lun 0 > da1: <IBM-ESXS MAY2073RC T107> Fixed Direct Access SCSI-5 device > da1: 300.000MB/s transfers, Tagged Queueing Enabled > da1: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) > cd0 at umass-sim1 bus 1 target 0 lun 0 > cd0: <HL-DT-ST RW/DVD GCC-4244N 1.02> Removable CD-ROM SCSI-0 device > cd0: 1.000MB/s transfers > cd0: Attempt to query device size failed: NOT READY, Medium not present > (da0:umass-sim0:0:0:0): got CAM status 0x4 > (da0:umass-sim0:0:0:0): fatal error, failed to attach to device > (da0:umass-sim0:0:0:0): lost device > (da0:umass-sim0:0:0:0): removing device entry > Trying to mount root from ufs:/dev/da1s1a > stray irq7 > bce0: link state changed to DOWN > vlan0: link state changed to DOWN > bce0: link state changed to UP > vlan0: link state changed to UP > stray irq7 > too many stray irq 7's: not logging anymore > mpt0: QUEUE FULL EVENT: Bus 0x00 Target 0x00 Depth 129 > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?45EEE409.6070106>