Date: Sun, 24 Apr 2022 04:37:09 -0700 From: Mark Millard <marklmi@yahoo.com> To: "freebsd-arm@freebsd.org" <arm@freebsd.org> Subject: Re: FYI: RPi* firmware tagged 1.20210805 appears to be the last to be bootable by FreeBSD via fdt use; sequence of 2 failure modes after that Message-ID: <836019DE-531E-4B49-8A82-0D8F84885C21@yahoo.com> In-Reply-To: <F43C3E9B-D391-4278-B038-185DA7BF71B0@yahoo.com> References: <F43C3E9B-D391-4278-B038-185DA7BF71B0@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
[I think I found the reason for the boot crash that is
a common failure to both failure modes. The 2nd mode
has other issues I've not analyzed.]
On 2022-Apr-23, at 23:45, Mark Millard <marklmi@yahoo.com> wrote:
> The following is based on a microsd card with 13.1-RC4 on
> it were I'd previously substituted my U-Boot 2022.04 build
> and tested with the RPi* firmware that is in the 13.1-RC4
> image. Here I've tried replacing the RPi* firmware and
> holding the rest constant.
>=20
> The boot tests are on a 8 GiByte RPi4B Rev 1.14 with the
> B0T stepping. I've not been copying over the linux kernels,
> which they also bundle with the firmware.
>=20
> [13.1-RC4 is just what I happened to use. I doubt anything
> here is special to 13.* or stable/13 or main [so: 14].
> (I do not use 12.* or stable/12.)]
>=20
> The observed status went like . . .
>=20
>=20
> firmware-1.20210805/boot/
>=20
> The RPi* release tagged 1.20210805 is the last version that
> FreeBSD booted with. (Other than booting, logging in, and
> shutting down, I've not been testing other aspects of
> operation.)
>=20
> =46rom what I've read, firmware-1.20210805/boot/ should be
> recent enough to handle the Rev 1.15 related PMIC variation.
>=20
> [I'll note that firmware build dates need not be the same day
> as the date encoded into the tag --in fact it is usually some
> earlier day. On rare occasion it can be a lot earlier, and
> there is an example of that below.]
>=20
>=20
> After firmware-1.20210805 there are 2 major failure modes.
> Both stop at the same sort of point in the messaging --but
> there is a huge difference in the count of earlier error
> messages. It looks to me like all the issues require
> FreeBSD changes if modern RPi* firmware/dtb's are to be
> usable via fdt.
I've noticed a difference between the working context and
the failing ones (both failure modes).
Failing:
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on =
simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
NOTE BELOW LINES MISSING HERE.
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
Working:
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on =
simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
START LINES MISSING ABOVE
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 26 =
on simplebus0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq =
30,31,32,33,34,35,36,37,38,39,40 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem =
0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on =
simplebus0
bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on =
simplebus0
gpioc1: <GPIO controller> on gpio1
END LINES MISSING ABOVE
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 73 on simplebus0
In particular:
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq =
30,31,32,33,34,35,36,37,38,39,40 on simplebus0
being missing means no bcm_dma_attach and that in turn means
that the static bcm_dma_sc =3D=3D NULL still.
The panic was: panic: vm_fault failed: ffff000000862134
where:
ffff000000862134 <bcm_dma_allocate+0x88> ldaxr x1, [x9]
which is part of:
int
bcm_dma_allocate(int req_ch)
{
struct bcm_dma_softc *sc =3D bcm_dma_sc;
int ch =3D BCM_DMA_CH_INVALID;
int i;
if (req_ch >=3D BCM_DMA_CH_MAX)
return (BCM_DMA_CH_INVALID);
/* Auto(req_ch < 0) or CH specified */
mtx_lock(&sc->sc_mtx);
. . .
So the likes of &sc->sc_mtx end up being a small offset
from address zero:
x9: 20
Thus the panic.
As to how bcm_dma_allocate happened without bcm_dma_attach
happening first . . .
The working context's dtb has the ordering:
(I also show mmcnr@ and the brcm,bcm2711-dma
just for reference.)
dma@7e007000 {
compatible =3D "brcm,bcm2835-dma";
. . .
mmc@7e300000 {
compatible =3D "brcm,bcm2835-mmc", =
"brcm,bcm2835-sdhci";
. . .
mmcnr@7e300000 {
compatible =3D "brcm,bcm2835-mmc", =
"brcm,bcm2835-sdhci";
. . .
dma@7e007b00 {
compatible =3D "brcm,bcm2711-dma";
But the failing context's dtb has the ordering:
(I also show mmcnr@ and the brcm,bcm2711-dma
just for reference.)
mmc@7e300000 {
compatible =3D "brcm,bcm2835-mmc", =
"brcm,bcm2835-sdhci";
. . .
dma@7e007000 {
compatible =3D "brcm,bcm2835-dma";
. . .
mmcnr@7e300000 {
compatible =3D "brcm,bcm2835-mmc", =
"brcm,bcm2835-sdhci";
. . .
dma@7e007b00 {
compatible =3D "brcm,bcm2711-dma";
So, for sequential handling in the failing case, the dma@7e007000
would use bcm_dma_allocate before the bcm_dma_probe/bcm_dma_attach
sequence had happened, leading to the crash.
Note: I used "fdt print /" from U-Boot to get the dtb and its
ordering. This was based on the address that the RPi* firmware
reports when debugging output is enabled (0x4000 here).
> The 1st mode happens for (I've added the -fails notation):
>=20
> firmware-1.20210831-fails/boot/
> firmware-1.20210928-fails/boot/
> firmware-1.20211007-fails/boot/
> firmware-1.20211029-fails/boot/
> firmware-1.20211118-fails/boot/
> firmware-1.20220308_buster-fails/boot/
> (The _buster one has firmware from 2021-Dec-01, which
> is before all the tagged releases listed below.
> It looks like the switch to the new major kernel
> version after buster came with other changes that
> FreeBSD has not tracked.)
>=20
>=20
> The 2nd mode happens for the following. (Again with extra
> notation.) There are a lot more error messages before the
> panic happens for these. The firmware builds for these
> are more recent than for the above list.
>=20
>=20
> firmware-1.20220118-fails/boot/
>=20
> firmware-1.20220120-fails/boot/
> firmware-1.20220308-fails-non-kernels-same-as-1.20220120/boot/
> (I did not repeat the testing of the unchanged firmware.
> I just did the "diff -r" to discover the lack of change.)
>=20
> firmware-1.20220328-fails/boot/
> =
firmware-1.20220331-fails-non-kernels-same-as-firmware-1.20220328-but-for-=
bcm2711-dtb-files/boot/
> (Since the .dtb for the RPi4B was different, I did test this.)
>=20
>=20
> The failures look like (each test shown) . . .
>=20
>=20
> firmware-1.20210831/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210251776 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f30000 mode 2 pages 1
> MAP 39f34000 mode 2 pages 3
> MAP 39f38000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f89a40
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20210928/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210251776 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f30000 mode 2 pages 1
> MAP 39f34000 mode 2 pages 3
> MAP 39f38000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f89a40
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20211007/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210251776 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f30000 mode 2 pages 1
> MAP 39f34000 mode 2 pages 3
> MAP 39f38000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f89a40
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20211029/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210251776 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f30000 mode 2 pages 1
> MAP 39f34000 mode 2 pages 3
> MAP 39f38000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f89a40
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20211118/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210251776 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f30000 mode 2 pages 1
> MAP 39f34000 mode 2 pages 3
> MAP 39f38000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f89a40
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20220308_buster-fails/boot/
> (The _buster one has firmware from 2021-Dec-01, which
> is before all the tagged releases listed below.)
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210251776 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f30000 mode 2 pages 1
> MAP 39f34000 mode 2 pages 3
> MAP 39f38000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> regfix2: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f89a40
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
>=20
> Below are the examples of the 2nd mode of failure . . .
>=20
>=20
> firmware-1.20220118/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210247680 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f2f000 mode 2 pages 1
> MAP 39f33000 mode 2 pages 3
> MAP 39f37000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> regfix2: <Fixed Regulator> on ofwbus0
> regfix3: <Fixed Regulator> on ofwbus0
> regfix4: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> regfix1: Cannot configure GPIO pin: 5
> REGNODE_INIT failed: 6
> regfix1: Cannot register regulator.
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f8b120
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
>=20
>=20
> firmware-1.20220120/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442929152 (8051 MB)
> avail memory =3D 8210247680 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f2f000 mode 2 pages 1
> MAP 39f33000 mode 2 pages 3
> MAP 39f37000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> regfix2: <Fixed Regulator> on ofwbus0
> regfix3: <Fixed Regulator> on ofwbus0
> regfix4: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> regfix1: Cannot configure GPIO pin: 5
> REGNODE_INIT failed: 6
> regfix1: Cannot register regulator.
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f8b120
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20220328/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442920960 (8051 MB)
> avail memory =3D 8210239488 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f2f000 mode 2 pages 1
> MAP 39f33000 mode 2 pages 3
> MAP 39f37000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> regfix2: <Fixed Regulator> on ofwbus0
> regfix3: <Fixed Regulator> on ofwbus0
> regfix4: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> regfix1: Cannot configure GPIO pin: 5
> REGNODE_INIT failed: 6
> regfix1: Cannot register regulator.
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f8b120
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
>=20
>=20
> firmware-1.20220331/boot/
>=20
> ---<<BOOT>>---
> WARNING: Cannot find freebsd,dts-version property, cannot check DTB =
compliance
> Copyright (c) 1992-2021 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
> The Regents of the University of California. All rights =
reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64
> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git =
llvmorg-13.0.0-0-gd7b669b3a303)
> VT(efifb): resolution 592x448
> module firmware already present!
> real memory =3D 8442920960 (8051 MB)
> avail memory =3D 8210239488 (7829 MB)
> Starting CPU 1 (1)
> Starting CPU 2 (2)
> Starting CPU 3 (3)
> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
> random: unblocking device.
> random: entropy device external interface
> MAP 39f2f000 mode 2 pages 1
> MAP 39f33000 mode 2 pages 3
> MAP 39f37000 mode 2 pages 4
> MAP 3b350000 mode 2 pages 16
> MAP fe100000 mode 0 pages 1
> kbd0 at kbdmux0
> ofwbus0: <Open Firmware Device Tree>
> simplebus0: <Flattened device tree simple bus> on ofwbus0
> ofw_clkbus0: <OFW clocks bus> on ofwbus0
> clk_fixed0: <Fixed clock> on ofw_clkbus0
> clk_fixed1: <Fixed clock> on ofw_clkbus0
> clk_fixed2: <Fixed clock> on ofwbus0
> clk_fixed3: <Fixed clock> on ofwbus0
> simplebus1: <Flattened device tree simple bus> on ofwbus0
> simplebus2: <Flattened device tree simple bus> on ofwbus0
> regfix0: <Fixed Regulator> on ofwbus0
> regfix1: <Fixed Regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> regfix2: <Fixed Regulator> on ofwbus0
> regfix3: <Fixed Regulator> on ofwbus0
> regfix4: <Fixed Regulator> on ofwbus0
> simplebus3: <Flattened device tree simple bus> on ofwbus0
> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem =
0x7d5d2000-0x7d5d2eff on simplebus0
> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0
> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gic0: <ARM Generic Interrupt Controller> mem =
0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x400460=
00-0x40047fff irq 30 on simplebus0
> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq =
14,15 on simplebus0
> gpiobus0: <OFW GPIO bus> on gpio0
> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0
> gpiobus1: <GPIO bus> on gpio1
> regfix0: Cannot set GPIO pin: 6
> REGNODE_INIT failed: 6
> regfix0: Cannot register regulator.
> regfix1: Cannot configure GPIO pin: 5
> REGNODE_INIT failed: 6
> regfix1: Cannot register regulator.
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on =
simplebus0
> gpioregulator0: <GPIO controlled regulator> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0
> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality =
1000
> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> clk_fixed4: <Fixed clock> disabled on ofwbus0
> clk_fixed4: Cannot FDT parameters.
> device_attach: clk_fixed4 attach returned 6
> gpioc0: <GPIO controller> on gpio0
> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on =
simplebus0
> uart0: console (115200,n,8,1)
> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 =
on simplebus0
> spibus0: <OFW SPI bus> on spi0
> spibus0: <unknown card> at cs 0 mode 0
> spibus0: <unknown card> at cs 1 mode 0
> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff =
irq 24 on simplebus0
> Fatal data abort:
> x0: ffffffff
> x1: ffff00000092b464
> x2: 0
> x3: 6
> x4: ffff000000fbf77c
> x5: ffff000000fbf72c
> x6: 4000000
> x7: 4000000
> x8: ffff000000dfb6a0
> x9: 20
> x10: 0
> x11: 1
> x12: 300000000006e65
> x13: fefefefeff0100
> x14: 1d
> x15: 0
> x16: 0
> x17: 0
> x18: ffff000000fbf7e0
> x19: ffffffff
> x20: 0
> x21: ffff000000bad000
> x22: ffff000000bad000
> x23: ffffa00000f8f038
> x24: ffff00000091b612
> x25: ffff0000008dfcfc
> x26: ffff000000943716
> x27: ffffa00000f8b120
> x28: 31e00000
> x29: ffff000000fbf7e0
> sp: ffff000000fbf7e0
> lr: ffff0000008680a0
> elr: ffff000000862134
> spsr: a00000c5
> far: 20
> esr: 96000004
> panic: vm_fault failed: ffff000000862134
> cpuid =3D 0
> time =3D 1
> KDB: stack backtrace:
> #0 0xffff000000516268 at kdb_backtrace+0x60
> #1 0xffff0000004c22bc at vpanic+0x174
> #2 0xffff0000004c2144 at panic+0x44
> #3 0xffff0000007f4928 at data_abort+0x204
> #4 0xffff0000007d5010 at handle_el1h_sync+0x10
> #5 0xffff00000086809c at bcm_sdhci_attach+0x314
> #6 0xffff00000086809c at bcm_sdhci_attach+0x314
> #7 0xffff000000502238 at device_attach+0x3fc
> #8 0xffff000000504324 at bus_generic_new_pass+0x120
> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0
> #12 0xffff000000506404 at root_bus_configure+0x40
> #13 0xffff000000439cf8 at mi_startup+0x11c
> #14 0xffff0000000008b4 at virtdone+0x78
> Uptime: 1s
=3D=3D=3D
Mark Millard
marklmi at yahoo.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?836019DE-531E-4B49-8A82-0D8F84885C21>