Date: Thu, 29 May 1997 18:33:37 +0300 (IDT) From: Nadav Eiron <nadav@barcode.co.il> To: Rick Osteen <rosteen@1eagle1.com> Cc: "P. van Leeuwen" <pvl@nanoteq.com>, freebsd-questions@FreeBSD.ORG Subject: Re: Newbee, please help Message-ID: <Pine.BSF.3.91.970529182901.19924B-100000@gatekeeper.barcode.co.il> In-Reply-To: <1.5.4.32.19970529131319.00748b08@192.41.5.53>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 29 May 1997, Rick Osteen wrote: > At 08:45 AM 5/29/97 +0200, you wrote: > >> Hello, > >> I did an install through the internet(anon. ftp) and found that after it > >> booted, it did not have the ip address and such that I had put in . > >> So I looked around here and there and found a spot to put them. Well it > >> works for the Lan(same network) but could not ping out to the rest of the > >> world. What gives? I need help there. > >> > >You have to edit /etc/resolv.conf to register your nameserver (you don't say > >whether you're using IP numbers or hostnames to ping) > >Your problem sounds like you also didn't configure your system to find your > >router / gateway. Look in rc.conf/sysconfig (depending on your version of > FreeBSD) > >and look for the line : > >defaultrouter="NO" > >and fill in your routers IP address between the quotes. > >Also make sure that you have filled in the IP number and netmask of your own > >machine in correctly. > > > > > > Here's the rc.conf file or the network part of it anyway. It's hard to tell *all* the things that may go wrong without knowig your setup (what routers you have, their addresses, your DNS server etc.), but I'll give it a shot: > > > ### Basic network options: ### > hostname="bsd.jimsroom.com" # Set this! > nisdomainname="NO" # Set to NIS domain if using NIS (or NO). > firewall="NO" # Set to firewall type or NO for none. > tcp_extensions="YES" # Allow RFC1323 & RFC1544 extensions (or NO). > #network_interfaces="lo0" # List of network interfaces (lo0 is loopback). First problem. LEAVE lo0 IN!!! Some things may go south without the loopback interface. Same goes for the ifconfig_lo0 below. Your network_interfaces should read "ed0 lo0" > network_interfaces="ed0" > #ifconfig_lo0="inet 127.0.0.1" # default loopback device configuration. > ifconfig_ed0="inet 207.123.60.6 broadcast 207.123.60.0" > > ### Network daemon (miscellaneous) & NFS options: ### > syslogd_enable="YES" # Run syslog daemon (or NO). > syslogd_flags="" # Flags to syslogd (if enabled). > inetd_flags="" # Optional flags to inetd (always enabled). > named_enable="NO" # Run named, the DNS server (or NO). > named_flags="" # Flags to named (if enabled). > kerberos_server_enable="NO" # Run a kerberos master server (or NO). > rwhod_enable="NO" # Run the rwho daemon (or NO). > amd_enable="NO" # Run amd service with $amd_flags (or NO). > amd_flags="-a /net -c 1800 -k i386 -d my.domain -l syslog /host /etc/amd.map" > nfs_client_enable="NO" # This host is an NFS client (or NO). > nfs_server_enable="NO" # This host is an NFS server (or NO). > weak_mountd_authentication="NO" # Running PCNFSD / other non-root nfsd (or NO). > nfs_reserved_port_only="NO" # Provide NFS only on secure port (or NO). > rpc_lockd_enable="NO" # Run NFS rpc.lockd (*broken!*) if nfs_server. > rpc_statd_enable="YES" # Run NFS rpc.statd if nfs_server (or NO). > portmap_enable="YES" # Run the portmapper service (or NO). > portmap_flags="" # Flags to portmap (if enabled). > xtend_enable="NO" # Run the X-10 power controller daemon. > xtend_flags="" # Flags to xtend (if enabled). > > ### Network Time Services options: ### > timed_enabled="NO" # Run the time daemon (or NO). > timed_flags="" # Flags to timed (if enabled). > ntpdate_enable="NO" # Run the ntpdate to sync time (or NO). > ntpdate_flags="" # Flags to ntpdate (if enabled). > xntpd_enable="NO" # Run xntpd Network Time Protocol (or NO). > xntpd_flags="" # Flags to xntpd (if enabled). > tickadj_enable="NO" # Run tickadj (or NO). > tickadj_flags="-Aq" # Flags to tickadj (if enabled). > > # Network Information Services (NIS) options: ### > nis_client_enable="NO" # We're an NIS client (or NO) > nis_client_flags="" # Flags to ypbind (if enabled). > nis_ypset_enable="NO" # Run ypset at boot time (or NO). > nis_ypset_flags="" # Flags to ypset (if enabled). > nis_server_enable="NO" # We're an NIS server (or NO) > nis_server_flags="" # Flags to ypserv (if enabled). > nis_ypxfrd_enable="NO" # Run rpc.ypxfrd at boot time (or NO). > nis_ypxfrd_flags="" # Flags to rpc.ypxfrd (if enabled). > nis_yppasswdd_enable="NO" # Run rpc.yppasswdd at boot time (or NO). > nis_yppasswdd_flags="" # Flags to rpc.yppasswdd (if enabled). > > ### Network routing options: ### > defaultrouter="206.123.60.1" # Set to default gateway (or NO). This won't work! You've set the host on the network 207.123.60. The router must be on the same net (looks like a typoe to me...) > static_routes="static" # Set to static route list (or leave empty). Should probably be left empty. > gateway_enable="NO" # Set to YES if this host will be a gateway. > router_enable="YES" # Set to YES to enable a routing daemon. You probably don't need a routing daemon. Unless you know why you need one I'd set router_enable to NO. > router="routed" # Name of routing daemon to use if enabled. > router_flags="-q" # Flags for routing daemon. > mrouted_enable="NO" # Do multicast routing (see /etc/mrouted.conf) > ipxgateway_enable="NO" # Set to YES to enable IPX routing. > ipxrouted_enable="NO" # Set to YES to run the IPX routing daemon. > ipxrouted_flags="" # Flags for IPX routing daemon. > arpproxy_all="" # obsolete kernel option ARP_PROXY_ALL equiv. > > rc.conf (71%) > > Please let me know what's wrong with this picture. I tried to... > > Rick Osteen > > Nadav
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.91.970529182901.19924B-100000>