Date: Thu, 29 Aug 2002 00:23:41 +0200 (CEST) From: =?ISO-8859-1?Q?G=E9rard_Roudier?= <groudier@free.fr> To: Holm Tiffe <holm@freibergnet.de> Cc: freebsd-scsi@FreeBSD.ORG Subject: Re: Camcontrol negotiate in -current Message-ID: <20020829001246.R5476-100000@localhost.my.domain> In-Reply-To: <20020826105329.B3473@pegasus.freiberg-net.de>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, 26 Aug 2002, Holm Tiffe wrote: > Hi guys, > > yesterday I've upgraded my -current from march to a current -current > and now /sbin/camcontrol negotiate da4 -R 10 -qac >/dev/null 2>&1 > is'nt working as expected anymore. > > I've used this, to keep an old bad Quantum drive working, that triggers > SCSI Bus hangs if it is running at the full negotiated 20Mhz speed. > > With the current camcontrol, I can switch tagged queueing on and of, > but I can't change the bus speed anymore: > > # /sbin/camcontrol negotiate da4 -R 10 -vac I don't run current for now. :) I would, anyway, suggest you to try either of the following: - Use full floating representation for the frequency (10.000 instead of just 10) and pray for being better understood. :) - Configure this lower transfer rate in the HBA NVRAM (if your HBA has NVRAM, of course), as the sym the driver understands most of user settings from Tekram HBA NVRAM. Gérard. > Current Parameters: > (pass6:sym0:0:6:0): sync parameter: 12 > (pass6:sym0:0:6:0): frequency: 20.000MHz > (pass6:sym0:0:6:0): offset: 16 > (pass6:sym0:0:6:0): bus width: 16 bits > (pass6:sym0:0:6:0): disconnection is enabled > (pass6:sym0:0:6:0): tagged queueing is enabled > sym0: SIM/HBA version: 1 > sym0: supports tag queue messages > sym0: supports SDTR message > sym0: supports 16 bit wide SCSI > sym0: supports MDP message > sym0: HBA engine count: 0 > sym0: maximum target: 15 > sym0: maximum LUN: 7 > sym0: highest path ID in subsystem: 0 > sym0: initiator ID: 7 > sym0: SIM vendor: FreeBSD > sym0: HBA vendor: Symbios > sym0: bus ID: 0 > sym0: base transfer speed: 3.300MB/sec > Unit is ready > New Parameters: > (pass6:sym0:0:6:0): sync parameter: 12 > (pass6:sym0:0:6:0): frequency: 20.000MHz > (pass6:sym0:0:6:0): offset: 16 > (pass6:sym0:0:6:0): bus width: 16 bits > (pass6:sym0:0:6:0): disconnection is enabled > (pass6:sym0:0:6:0): tagged queueing is enabled > > > The controller is an Tekram DC39x (have to look at it for > the correct model) and the disk is an QUANTUM VIKING 4.5 SCA 880R. > J"org Wunsch (joerg@freebsd.org) can reproduce this. > > I have an new disk here, but I can't get the data from the old > drive, the tape rewinds after BDR. > > Holm > -- > FreibergNet Systemhaus GbR Holm Tiffe * Administration, Development > Systemhaus für Daten- und Netzwerktechnik phone +49 3731 781279 > Unternehmensgruppe Liebscher & Partner fax +49 3731 781377 > D-09599 Freiberg * Am St. Niclas Schacht 13 http://www.freibergnet.de > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-scsi" in the body of the message > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020829001246.R5476-100000>