Date: Sun, 12 Nov 2006 17:44:10 +0100 From: Aleksandra =?iso-8859-2?Q?Brzezi=F1ska?= <aleksandra.brzezinska@unixy.pl> To: Zoran Kolic <zkolic@sbb.co.yu> Cc: freebsd-mobile@freebsd.org Subject: Re: Too hot temperature of disk - HP Compaq nc6220 Message-ID: <1163349851.3968.14.camel@ola.pl> In-Reply-To: <20061112142233.GA638@faust.net> References: <20061112120058.568CF16A6C8@hub.freebsd.org> <20061112142233.GA638@faust.net>
next in thread | previous in thread | raw e-mail | index | archive | help
> Could you elaborate a little bit more > on possible hardware failure? Sorry, I didn't know what could be important. > Output of "sysctl hw.acpi" et alia. kern.version: FreeBSD 6.1-RELEASE #0: Sun May 7 04:32:43 UTC 2006 root@opus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC debug.cpufreq.lowest: 0 debug.cpufreq.verbose: 0 debug.acpi.do_powerstate: 1 debug.acpi.acpi_ca_version: 0x20041119 debug.acpi.semaphore_debug: 0 hw.acpi.supported_sleep_state: S3 S4 S5 hw.acpi.power_button_state: S5 hw.acpi.sleep_button_state: S3 hw.acpi.lid_switch_state: NONE hw.acpi.standby_state: S1 hw.acpi.suspend_state: S3 hw.acpi.sleep_delay: 1 hw.acpi.s4bios: 1 hw.acpi.verbose: 0 hw.acpi.reset_video: 1 hw.acpi.cpu.cx_supported: C1/1 C2/2 C3/38 hw.acpi.cpu.cx_lowest: C1 hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00% hw.acpi.battery.life: -1 hw.acpi.battery.time: -1 hw.acpi.battery.state: 7 hw.acpi.battery.units: 2 hw.acpi.battery.info_expire: 5 hw.acpi.acline: 1 hw.acpi.thermal.min_runtime: 0 hw.acpi.thermal.polling_rate: 10 hw.acpi.thermal.tz0.temperature: 59.0C hw.acpi.thermal.tz0.active: 2 hw.acpi.thermal.tz0.passive_cooling: 1 hw.acpi.thermal.tz0.thermal_flags: 0 hw.acpi.thermal.tz0._PSV: 100.0C hw.acpi.thermal.tz0._HOT: -1 hw.acpi.thermal.tz0._CRT: 105.0C hw.acpi.thermal.tz0._ACx: 80.0C 70.0C 55.0C 35.0C -1 -1 -1 -1 -1 -1 hw.acpi.thermal.tz1.temperature: 45.0C hw.acpi.thermal.tz1.active: -1 hw.acpi.thermal.tz1.passive_cooling: 0 hw.acpi.thermal.tz1.thermal_flags: 0 hw.acpi.thermal.tz1._PSV: -1 hw.acpi.thermal.tz1._HOT: -1 hw.acpi.thermal.tz1._CRT: 103.0C hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 hw.acpi.thermal.tz2.temperature: 16.0C hw.acpi.thermal.tz2.active: -1 hw.acpi.thermal.tz2.passive_cooling: 0 hw.acpi.thermal.tz2.thermal_flags: 0 hw.acpi.thermal.tz2._PSV: 60.0C hw.acpi.thermal.tz2._HOT: -1 hw.acpi.thermal.tz2._CRT: 105.0C hw.acpi.thermal.tz2._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 > If you are sure that box is healthy, > would you include "cpufreq", recompile > and post temperatures? I loaded cpufreq.ko (default, without any compilation), effect: ola# kldload cpufreq acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: Please update driver or contact the maintainer. est: cpu_vendor GenuineIntel, msr 6120e2906000e29, bus_clk, 64 device_attach: est0 attach returned 6 the same message again p4tcc0: <CPU Frequency Thermal Control> on cpu0 acpi_perf0: <ACPI CPU Frequency Control> on cpu0 acpi_perf0: failed in PERF_STATUS attach device_attach: acpi_perf0 attach returned 6 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: Please update driver or contact the maintainer. est: cpu_vendor GenuineIntel, msr 6120e2906000e29, bus_clk, 64 device_attach: est0 attach returned 6 the same message again > Does this laptop have bios options for > temp regulation? No it hasn't > Any changes in conf? My changes? No - i'm bsd noob. > Note in /var/log/messages? Nov 10 21:13:15 ola kernel: ACPI APIC Table: <HP 0944 > Nov 10 21:13:15 ola kernel: acpi0: <HP 0944> on motherboard Nov 10 21:13:15 ola kernel: acpi_bus_number: can't get _ADR Nov 10 21:13:15 ola last message repeated 5 times Nov 10 21:13:15 ola kernel: acpi0: Power Button (fixed) Nov 10 21:13:15 ola kernel: acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0 Nov 10 21:13:15 ola kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 Nov 10 21:13:15 ola kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 Nov 10 21:13:15 ola kernel: cpu0: <ACPI CPU> on acpi0 Nov 10 21:13:15 ola kernel: acpi_perf0: <ACPI CPU Frequency Control> on cpu0 Nov 10 21:13:15 ola kernel: acpi_perf0: failed in PERF_STATUS attach Nov 10 21:13:15 ola kernel: device_attach: acpi_perf0 attach returned 6 Nov 10 21:13:15 ola kernel: acpi_perf0: <ACPI CPU Frequency Control> on cpu0 Nov 10 21:13:15 ola kernel: acpi_perf0: failed in PERF_STATUS attach Nov 10 21:13:15 ola kernel: device_attach: acpi_perf0 attach returned 6 Nov 10 21:13:15 ola kernel: acpi_throttle0: <ACPI CPU Throttling> on cpu0 Nov 10 21:13:15 ola kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 Nov 10 21:13:15 ola kernel: pci0: <ACPI PCI bus> on pcib0 Nov 10 21:13:15 ola kernel: pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 Nov 10 21:13:15 ola kernel: pci16: <ACPI PCI bus> on pcib1 Nov 10 21:13:15 ola kernel: pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 Nov 10 21:13:15 ola kernel: pci2: <ACPI PCI bus> on pcib3 Nov 10 21:13:15 ola kernel: battery0: <ACPI Control Method Battery> on acpi0 Nov 10 21:13:15 ola kernel: battery1: <ACPI Control Method Battery> on acpi0 Nov 10 21:13:15 ola kernel: acpi_acad0: <AC Adapter> on acpi0 Nov 10 21:13:15 ola kernel: acpi_button0: <Sleep Button> on acpi0 Nov 10 21:13:15 ola kernel: acpi_lid0: <Control Method Lid Switch> on acpi0 Nov 10 21:13:15 ola kernel: acpi_tz0: <Thermal Zone> on acpi0 Nov 10 21:13:15 ola kernel: acpi_tz1: <Thermal Zone> on acpi0 Nov 10 21:13:15 ola kernel: acpi_tz2: <Thermal Zone> on acpi0 Nov 10 22:27:28 ola su: olka to root on /dev/ttyp5 Nov 10 23:20:16 ola kernel: acpi_tz0: WARNING - current temperature (106.0C) exceeds safe limits Nov 10 23:20:16 ola root: WARNING: system temperature too high, shutting down soon! Nov 10 23:20:16 ola syslogd: exiting on signal 15 > Acpi or apm? ACPI Thanks for help, Aleksandra Brzezinska
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1163349851.3968.14.camel>