Date: Sun, 21 Mar 1999 12:13:13 +1100 From: GuRu <guru@b0rk.looksharp.net> To: freebsd-stable@freebsd.org Subject: Strange boot problems Message-ID: <3.0.3.32.19990321121313.00975bd0@b0rk.looksharp.net>
next in thread | raw e-mail | index | archive | help
Recently I've been encountering strange boot problems with 3.1-RELEASE
updated to 3.1-STABLE on a brand new system. None of the kernels I've built
(or even kernel.GENERIC) will boot unless I hit a key at startup and enter
boot -cv, then the kernels might boot properly. I've tried recompiling
kernels with all different combinations of options but it always comes back
to the same, unless I use boot -cv, the kernel fails to boot. This is the
specific error message.
Considering FFS root f/s.
changing root device to wd0s1a
wd0s1: type 0xa5, start 63, end = 8402939, size 8402877 : OK
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x0
fault code = supervisor read, page not present
instruction pointer = 0x8:0x0
stack pointer = 0x10:0xf41dad20
frame pointer = 0x10:0xf41dad44
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 1 (swapper)
interrupt mask =
trap number = 12
panic: page fault
Other related information :
hip0: <AcerLabs M1541 (Aladdin-V) PCI host bridge> rev 0x04 on pci0.0.0
found-> vendor=0x10b9, dev=0x5243, revid=0x04
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
chip1: <AcerLabs M5243 PCI-PCI bridge> rev 0x04 on pci0.1.0
found-> vendor=0x10b9, dev=0x7101, revid=0x00
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
chip2: <PCI to 0x80 bridge (vendor=10b9 device=7101)> rev 0x00 on pci0.3.0
found-> vendor=0x10b9, dev=0x1533, revid=0xc3
class=06-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
chip3: <AcerLabs M1533 portable PCI-ISA bridge> rev 0xc3 on pci0.7.0
found-> vendor=0x1113, dev=0x1211, revid=0x10
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=12
map[0]: type 4, range 32, base 0000d800, size 8
map[1]: type 1, range 32, base df000000, size 8
ide_pci0: <Acer Aladdin IV/V (M5229) Bus-master IDE controller> rev 0xc1
int a irq 0 on pci0.15.0
ide_pci: busmaster 0 status: a4 from port: 0000d402
ide_pci: ide0:0 has been configured for DMA by BIOS
ide_pci: busmaster 1 status: 80 from port: 0000d40a
wdc0 at 0x1f0-0x1f7 irq 14 flags 0xa0ffa0ff on isa
wdc0: unit 0 (wd0): <ST34321A>, DMA, 32-bit, multi-block-16
wd0: 4103MB (8404830 sectors), 8894 cyls, 15 heads, 63 S/T, 512 B/S
wd0: ATA INQUIRE valid = 0007, dmamword = 0007, apio = 0003, udma = 0407
Thanks in advance for any insights...
--
K
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3.0.3.32.19990321121313.00975bd0>