From owner-freebsd-questions  Fri May 28 11:34: 0 1999
Delivered-To: freebsd-questions@freebsd.org
Received: from albert.osu.cz (albert.osu.cz [195.113.106.11])
	by hub.freebsd.org (Postfix) with ESMTP id 3AC4E14DC5
	for <freebsd-questions@FreeBSD.ORG>; Fri, 28 May 1999 11:33:44 -0700 (PDT)
	(envelope-from belkovics@albert.osu.cz)
Received: from localhost (belkovics@localhost)
	by albert.osu.cz (8.9.2/8.9.2) with ESMTP id UAA02884;
	Fri, 28 May 1999 20:33:40 +0200 (MET DST)
	(envelope-from belkovics@albert.osu.cz)
Date: Fri, 28 May 1999 20:33:40 +0200 (MET DST)
From: Josef Belkovics <belkovics@albert.osu.cz>
To: Alex Nygren <anygren@architype.com>
Cc: Alex Nygren <alex@architype.com>, freebsd-questions@FreeBSD.ORG
Subject: Re: Kernel Config Question
In-Reply-To: <Pine.LNX.4.04.9905281051400.3965-100000@nikita.localdomain>
Message-ID: <Pine.BSF.4.05.9905282028340.2881-100000@albert.osu.cz>
MIME-Version: 1.0
Content-Type: TEXT/PLAIN; charset=US-ASCII
Sender: owner-freebsd-questions@FreeBSD.ORG
Precedence: bulk
X-Loop: FreeBSD.ORG

On Fri, 28 May 1999, Alex Nygren wrote:

> Thanks for the help.
> 
> It looks like the file is /kernel.conf, and when I look to edit it; it is
> just a list of values:
> 
> di ze0
> di lnc0
> di le0
> di ie0
> di fe0
> di ep0
> di cs0
> di wt0
> di scd0
> di mcd0
> di matcdc0
> di bt0
> di aha0
> q         
> 
> Where can I find info on how to modify it; I don't see the device that I
> need to modify, ed0.  Any ideas?
 
Info probably does not exist. But commands are from boot -c. di ed0 means
disable ep0. en ed0 means enable enable ed0 etc. Use boot -c => line
config (not visual) and all will be clear. po ed0 0x300 set up port etc.

> THanks,
> Alex
> 
> On Fri, 28 May 1999, Josef Belkovics wrote:
> 
> > You must manually made changes into /boot/kernel.conf (maybe name isn't
> > correct, but look on /boot). In old good times fbsd did it alone, but now
> > you must a bit work.
> > 
> > > I am a FreeBSD newbie, and am having some trouble making my driver
> > > changes stick.  FreeBSD seems to recognize my NE2000 card on irq 10,
> > > port 0x280.  However the card is at irq 11, port 0x280.  So, I boot up
> > > with boot -c, manually configure the card in visual mode and, of course,
> > > tell the kernel not to load the drivers I do not need.  When I save my
> > > changes with 'q' it boots up fine, and the card works perfect!  However,
> > > when I reboot, the kernel loads every driver up, and defaults back to
> > > irq 10 for my NE2000.  How can I make the configuration changes I make
> > > "stick"?  I would be most appreciative for any information.  I am sure
> > > it's quite trivial, I just don't know where to look.  If some one could
> > > reply back to me at my private email (I am not a subscriber to this
> > > list) of where I might be able to find the info on how to do this, or
> > > just how to do this it would be great!
> > > 
> > > Thanks in advance,
> > > 
> > > Alex Nygren
> > > 
> > > 
> > > 
> > > 
> > > To Unsubscribe: send mail to majordomo@FreeBSD.org
> > > with "unsubscribe freebsd-questions" in the body of the message
> > > 
> > 
> > 
> > 
> 
> 



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message