Date: Wed, 28 Jan 2004 12:41:20 +0100 From: fjaspers@xs4all.nl To: freebsd-isdn@freebsd.org Subject: RE: AVM ISDN Fritz 2.0 PCI card Message-ID: <20040128114120.GA70001@xs4all.nl>
next in thread | raw e-mail | index | archive | help
Hi I'm using a AVM Fritz!Card PCI Version 2 on my FreeBSD 5.0 RELEASE box. It's more or less stable. sometimes when connecting it gives messges like: i4b-L1 ifpi2_isacsx_exir_hdlr: EXIRQ Rx Frame Overflow i4b-L1 ifpi2_isacsx_irq: unit 0: Data Overrun error i4b-L2 i4b_T202_timeout: unit 0, N202 = 3 I just have to connect again in that case. I experienced some lockups too, however that was when running my machine under linux. Here is my isdnd.conf it is setup for working with userland ppp, and for receiving and answering incoming. Maybe this helps you. Do u have any log messages? Frans. (fjaspers@xs4all.nl) isdnd.conf: #============================================================================== # SYSTEM section: isdnd global configuration parameters #============================================================================== system monitor-allowed = no # global switch: monitor on/off monitor = "/var/run/isdn-monitor" monitor-access = fullcmd # all commands. ratesfile = /etc/isdn/isdnd.rates # name & location of rates file regexpr = "[Cc]all from .* to Frans Jaspers" regprog = isdntel.notify aliasing = on # Aliasing. aliasfile = /etc/isdn/isdntel.alias # Alias file. # prefixes voor incoming calls. add-prefix = on prefix-national = "0" prefix-international = "+31" beepconnect = on extcallattr = on isdntime = on rtprio = 25 #=========================================================================== # controller section #=========================================================================== controller protocol = dss1 #============================================================================== # entry section. Userland ppp device 0. #============================================================================== entry name = userppp0 usrdevicename = rbch usrdeviceunit = 0 isdncontroller = 0 isdnchannel = 1 local-phone-dialout = 1234567 # This *MUST* be your local number remote-phone-dialout = 1234567 # ppp(8) will override this local-phone-incoming = 1234567 # this is my number remote-phone-incoming = * # i call this remote number remdial-handling = first dialin-reaction = ignore dialout-type = normal b1protocol = hdlc idletime-incoming = 900 # Should be larger than ppp's timeout idletime-outgoing = 900 # Should be larger than ppp's timeout unitlength = 0 unitlengthsrc = conf dialretries = 1 dialrandincr = on recoverytime = 1 # Should be smaller than ppp's redial usedown = off downtries = 2 downtime = 30 #============================================================================== # entry section. Userland ppp device 1. #============================================================================== entry name = userppp1 usrdevicename = rbch usrdeviceunit = 1 isdncontroller = 0 isdnchannel = 2 local-phone-dialout = 1234567 # This *MUST* be your local number remote-phone-dialout = 1234567 # ppp(8) will override this local-phone-incoming = 1234567 # this is my number remote-phone-incoming = * # i call this remote number remdial-handling = first dialin-reaction = ignore dialout-type = normal b1protocol = hdlc idletime-incoming = 900 # Should be larger than ppp's timeout idletime-outgoing = 900 # Should be larger than ppp's timeout unitlength = 0 unitlengthsrc = conf dialretries = 1 dialrandincr = on recoverytime = 1 # Should be smaller than ppp's redial usedown = off downtries = 2 downtime = 30 #============================================================================== # entry section. Telephony. #============================================================================== entry name = i4btel # name in logfiles. usrdevicename = tel # the device the data traffic # should be routed to. usrdeviceunit = 0 # unit number isdncontroller = 0 # the ISDN controller number to be used. isdnchannel = -1 # channel(1/2) to use or 0 or -1 for any direction = inout # in, out, inout local-phone-incoming = 1234567 # this is my number remote-phone-incoming = * # i call this remote number local-phone-dialout = 1234567 # My number. remote-phone-dialout = * # I call this number. dialin-reaction = answer # what happenes if someone dials in: answerprog = isdntel.sh # Program when someone dials in. b1protocol = raw # type of protocol on the B-channel. alert = 15 idletime-incoming = 5 ------------------------------------------------------------------------------- End of isdnd.conf
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040128114120.GA70001>