Date: Fri, 14 Jun 2002 10:01:01 -0400 From: Don Bowman <don@sandvine.com> To: 'Holger Kipp' <holger.kipp@alogis.com>, Don Bowman <don@sandvine.com> Cc: "'freebsd-stable@freebsd.org'" <freebsd-stable@FreeBSD.ORG> Subject: RE: bge0 system hang when PCI-X enabled Message-ID: <FE045D4D9F7AED4CBFF1B3B813C8533767646A@mail.sandvine.com>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Holger Kipp wrote:
> could you send "dmesg" and "mptable" output?
> (both cases - PCI-X enabled, PCI-X disabled)
The machine just hangs. Console dead, everything dead. Call it a crash I
guess.
I attached the files for the two cases.
These were run on two machines (identical, but I upgraded the bios on
one of them which accounts for some slightly different addresses).
The behaviour doesn't track the bios, it does track the jumper, so I think
this won't matter.
For what its worth, our older ASUS P4 motherboards for sure crash
when there's shared interrupts on the xl0.
[-- Attachment #2 --]
===============================================================================
MPTable, version 2.0.15
looking for EBDA pointer @ 0x040e, found, searching EBDA @ 0x0009f400
searching CMOS 'top of mem' @ 0x0009f000 (636K)
searching default 'top of mem' @ 0x0009fc00 (639K)
searching BIOS @ 0x000f0000
MP FPS found in BIOS @ physical addr: 0x000f7030
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f7030
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x2e
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x0009f970
signature: 'PCMP'
base table length: 396
version: 1.4
checksum: 0x1f
OEM ID: ' '
Product ID: 'Kings Canyon'
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 38
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x14 BSP, usable 15 2 4 0x3febfbff
6 0x14 AP, usable 15 2 4 0x3febfbff
1 0x14 AP, usable 15 2 4 0x3febfbff
7 0x14 AP, usable 15 2 4 0x3febfbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
3 PCI
4 PCI
5 ISA
--
I/O APICs: APIC ID Version State Address
2 0x20 usable 0xfec00000
3 0x20 usable 0xfec80000
4 0x20 usable 0xfec80400
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 5 0 2 0
INT active-hi edge 5 1 2 1
INT active-hi edge 5 0 2 2
INT active-hi edge 5 3 2 3
INT active-hi edge 5 4 2 4
INT active-hi edge 5 5 2 5
INT active-hi edge 5 6 2 6
INT active-hi edge 5 7 2 7
INT active-hi edge 5 8 2 8
INT active-hi edge 5 9 2 9
INT active-lo level 0 29:B 2 19
INT active-lo level 0 29:A 2 16
INT active-hi edge 5 12 2 12
INT active-hi edge 5 13 2 13
INT active-hi edge 5 14 2 14
INT active-hi edge 5 15 2 15
INT active-lo level 0 29:C 2 18
INT active-lo level 2 1:A 4 0
INT active-lo level 3 2:A 3 4
INT active-lo level 3 2:B 3 5
INT active-lo level 3 4:A 3 7
INT active-lo level 4 1:A 2 16
INT active-lo level 4 2:A 2 17
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 5 0 255 0
NMI active-hi edge 5 0 255 1
-------------------------------------------------------------------------------
dmesg output:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RC #1: Thu Jun 13 11:01:59 EDT 2002
root@TPC-C3-25:/new/obj/new/src/sys/TPC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1996.60-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 1073217536 (1048064K bytes)
avail memory = 1039499264 (1015136K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 24 pins in IOAPIC #1
Programming 24 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 6, version: 0x00050014, at 0xfee00000
cpu2 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000
io1 (APIC): apic id: 3, version: 0x00178020, at 0xfec80000
io2 (APIC): apic id: 4, version: 0x00178020, at 0xfec80400
Preloaded elf kernel "kernel" at 0xc040c000.
netsmb_dev: loaded
md0: Malloc disk
Using $PIR table, 24 entries at 0xc00fde40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 10
IOAPIC #0 intpin 18 -> irq 11
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
IOAPIC #2 intpin 0 -> irq 16
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5701 Gigabit Ethernet> mem 0xfc200000-0xfc20ffff irq 16 at device 1.0 on pci2
bge0: Ethernet address: 00:04:76:dd:2a:e0
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #1 intpin 4 -> irq 17
IOAPIC #1 intpin 5 -> irq 18
IOAPIC #1 intpin 7 -> irq 19
pci3: <PCI bus> on pcib3
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2000-0x20ff mem 0xfc340000-0xfc340fff irq 17 at device 2.0 on pci3
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2400-0x24ff mem 0xfc341000-0xfc341fff irq 18 at device 2.1 on pci3
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
pci3: <unknown card> (vendor=0x8086, dev=0x100d) at 4.0 irq 19
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1400-0x141f irq 2 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1420-0x143f irq 10 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x1440-0x145f irq 11 at device 29.2 on pci0
uhci2: (New UHCI DeviceId=0x24878086)
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: (0x24878086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 17 -> irq 20
pci4: <PCI bus> on pcib4
pci4: <ATI Mach64-GR graphics accelerator> at 1.0 irq 2
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x3400-0x343f mem 0xfc420000-0xfc43ffff,0xfc401000-0xfc401fff irq 20 at device 2.0 on pci4
fxp0: Ethernet address 00:30:48:12:36:07
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1460-0x146f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 0
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xce800-0xcffff,0xd0000-0xd0fff,0xd8000-0xdbfff,0xdc000-0xdffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to accept, logging disabled
BRIDGE 020214 loaded
DUMMYNET initialized (011031)
SMP: AP CPU #2 Launched!
acd0: CDROM <MATSHITA CR-177> at ata1-master PIO4
Waiting 2 seconds for SCSI devices to settle
SMP: AP CPU #3 Launched!
SMP: AP CPU #1 Launched!
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <SUPER GEM318 0> Fixed Processor SCSI-2 device
pass2: 3.300MB/s transfers
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST318452LC 0004> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST318452LC 0004> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
Mounting root from ufs:/dev/da0s1a
===============================================================================
[-- Attachment #3 --]
===============================================================================
MPTable, version 2.0.15
looking for EBDA pointer @ 0x040e, found, searching EBDA @ 0x0009f400
searching CMOS 'top of mem' @ 0x0009ec00 (635K)
searching default 'top of mem' @ 0x0009fc00 (639K)
searching BIOS @ 0x000f0000
MP FPS found in BIOS @ physical addr: 0x000f7040
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f7040
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x0e
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x0009f990
signature: 'PCMP'
base table length: 388
version: 1.4
checksum: 0x45
OEM ID: ' '
Product ID: 'Kings Canyon'
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 37
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x14 BSP, usable 15 2 4 0x3febfbff
6 0x14 AP, usable 15 2 4 0x3febfbff
1 0x14 AP, usable 15 2 4 0x3febfbff
7 0x14 AP, usable 15 2 4 0x3febfbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
3 PCI
4 PCI
5 ISA
--
I/O APICs: APIC ID Version State Address
2 0x20 usable 0xfec00000
3 0x20 usable 0xfec80000
4 0x20 usable 0xfec80400
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 5 0 2 0
INT active-hi edge 5 1 2 1
INT active-hi edge 5 0 2 2
INT active-hi edge 5 3 2 3
INT active-hi edge 5 4 2 4
INT active-hi edge 5 5 2 5
INT active-hi edge 5 6 2 6
INT active-lo level 0 29:C 2 18
INT active-hi edge 5 8 2 8
INT active-hi edge 5 9 2 9
INT active-lo level 0 29:B 2 19
INT active-lo level 0 29:A 2 16
INT active-hi edge 5 12 2 12
INT active-hi edge 5 13 2 13
INT active-hi edge 5 14 2 14
INT active-hi edge 5 15 2 15
INT active-lo level 2 1:A 4 0
INT active-lo level 3 2:A 3 4
INT active-lo level 3 2:B 3 5
INT active-lo level 3 4:A 3 7
INT active-lo level 4 1:A 2 16
INT active-lo level 4 2:A 2 17
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 5 0 255 0
NMI active-hi edge 5 0 255 1
-------------------------------------------------------------------------------
dmesg output:
u2 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000
io1 (APIC): apic id: 3, version: 0x00178020, at 0xfec80000
io2 (APIC): apic id: 4, version: 0x00178020, at 0xfec80400
Preloaded elf kernel "kernel" at 0xc0415000.
netsmb_dev: loaded
md0: Malloc disk
Using $PIR table, 24 entries at 0xc00fde40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 7
IOAPIC #0 intpin 18 -> irq 10
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
IOAPIC #2 intpin 0 -> irq 11
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5701 Gigabit Ethernet> mem 0xfc200000-0xfc20ffff irq 11 at device 1.0 on pci2
bge0: Ethernet address: 00:04:76:dd:2c:d0
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #1 intpin 4 -> irq 16
IOAPIC #1 intpin 5 -> irq 17
IOAPIC #1 intpin 7 -> irq 18
pci3: <PCI bus> on pcib3
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2000-0x20ff mem 0xfc340000-0xfc340fff irq 16 at device 2.0 on pci3
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2400-0x24ff mem 0xfc341000-0xfc341fff irq 17 at device 2.1 on pci3
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.3.8> port 0x2800-0x281f mem 0xfc300000-0xfc31ffff,0xfc320000-0xfc33ffff irq 18 at device 4.0 on pci3
em0: Speed:100 Mbps Duplex:Full
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1400-0x141f irq 2 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1420-0x143f irq 7 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x1440-0x145f irq 10 at device 29.2 on pci0
uhci2: (New UHCI DeviceId=0x24878086)
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: (0x24878086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 17 -> irq 19
pci4: <PCI bus> on pcib4
pci4: <ATI Mach64-GR graphics accelerator> at 1.0 irq 2
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x3400-0x343f mem 0xfc420000-0xfc43ffff,0xfc401000-0xfc401fff irq 19 at device 2.0 on pci4
fxp0: Ethernet address 00:30:48:12:33:d2
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1460-0x146f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2483) at 31.3 irq 0
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xce800-0xcffff,0xd0000-0xd0fff,0xd8000-0xdbfff,0xdc000-0xdffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to accept, logging disabled
BRIDGE 020214 loaded
DUMMYNET initialized (011031)
SMP: AP CPU #2 Launched!
acd0: CDROM <MATSHITA CR-177> at ata1-master PIO4
Waiting 2 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <SUPER GEM318 0> Fixed Processor SCSI-2 device
pass2: 3.300MB/s transfers
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST318452LC 0003> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST318452LC 0003> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
Mounting root from ufs:/dev/da0s1a
WARNING: / was not properly dismounted
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
em0: promiscuous mode enabled
em0: promiscuous mode disabled
em0: promiscuous mode enabled
em0: promiscuous mode disabled
em0: promiscuous mode enabled
nfs server dbowman-w2k.sandvine.com:/m: not responding
nfs server dbowman-w2k.sandvine.com:/m: is alive again
nfs server dbowman-w2k.sandvine.com:/m: not responding
nfs server dbowman-w2k.sandvine.com:/m: is alive again
nfs server dbowman-w2k.sandvine.com:/m: not responding
nfs server dbowman-w2k.sandvine.com:/m: is alive again
nfs server dbowman-w2k.sandvine.com:/m: not responding
nfs server dbowman-w2k.sandvine.com:/m: is alive again
nfs server dbowman-w2k.sandvine.com:/m: not responding
nfs server dbowman-w2k.sandvine.com:/m: is alive again
pid 1401 (p2p), uid 502: exited on signal 11 (core dumped)
em0: promiscuous mode disabled
boot() called on cpu#2
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped
syncing disks... 1
done
ient: bootp in /etc/inetd.cohF. Also make sure you
cpu_reset: Restarting BSP
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RC #8: Thu Jun 13 23:02:35 EDT 2002
root@TPC-C2-32:/usr/obj/usr/src/sys/TPC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1996.60-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 1073217536 (1048064K bytes)
avail memory = 1039478784 (1015116K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 24 pins in IOAPIC #1
Programming 24 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 6, version: 0x00050014, at 0xfee00000
cpu2 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000
io1 (APIC): apic id: 3, version: 0x00178020, at 0xfec80000
io2 (APIC): apic id: 4, version: 0x00178020, at 0xfec80400
Preloaded elf kernel "kernel" at 0xc041d000.
netsmb_dev: loaded
md0: Malloc disk
Using $PIR table, 24 entries at 0xc00fde40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 7
IOAPIC #0 intpin 18 -> irq 10
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
IOAPIC #2 intpin 0 -> irq 11
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5701 Gigabit Ethernet> mem 0xfc200000-0xfc20ffff irq 11 at device 1.0 on pci2
bge0: Ethernet address: 00:04:76:dd:2c:d0
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #1 intpin 4 -> irq 16
IOAPIC #1 intpin 5 -> irq 17
IOAPIC #1 intpin 7 -> irq 18
pci3: <PCI bus> on pcib3
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2000-0x20ff mem 0xfc340000-0xfc340fff irq 16 at device 2.0 on pci3
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2400-0x24ff mem 0xfc341000-0xfc341fff irq 17 at device 2.1 on pci3
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.3.8> port 0x2800-0x281f mem 0xfc300000-0xfc31ffff,0xfc320000-0xfc33ffff irq 18 at device 4.0 on pci3
em0: Speed:100 Mbps Duplex:Full
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1400-0x141f irq 2 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1420-0x143f irq 7 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x1440-0x145f irq 10 at device 29.2 on pci0
uhci2: (New UHCI DeviceId=0x24878086)
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: (0x24878086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 17 -> irq 19
pci4: <PCI bus> on pcib4
pci4: <ATI Mach64-GR graphics accelerator> at 1.0 irq 2
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x3400-0x343f mem 0xfc420000-0xfc43ffff,0xfc401000-0xfc401fff irq 19 at device 2.0 on pci4
fxp0: Ethernet address 00:30:48:12:33:d2
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1460-0x146f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ichsmb0: <Intel 82801CA (ICH3) SMBus controller> port 0x1100-0x111f irq 0 at device 31.3 on pci0
pci_cfgintr_search: linked (61) to configured irq 19 at 4:2:0
pci_cfgintr: 0:31 INTB routed to irq 19
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus general purpose I/O> on smbus0
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xce800-0xcffff,0xd0000-0xd0fff,0xd8000-0xdbfff,0xdc000-0xdffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
pcf0: <PCF8584 I2C bus controller> at port 0x320-0x321 irq 5 on isa0
iicbus0: <Philips I2C bus> on pcf0 addr 0xaa
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to accept, logging disabled
BRIDGE 020214 loaded
DUMMYNET initialized (011031)
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #1 Launched!
acd0: CDROM <MATSHITA CR-177> at ata1-master PIO4
Waiting 2 seconds for SCSI devices to settle
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <SUPER GEM318 0> Fixed Processor SCSI-2 device
pass2: 3.300MB/s transfers
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST318452LC 0003> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST318452LC 0003> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
Mounting root from ufs:/dev/da0s1a
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
boot() called on cpu#2
Waiting (max 60 seconds) for system process `vnlru' to stop...stersity of California. All rights reserved.
FreeBSD 4.6-RC #6: Thu Jun 13 19:53:24 EDT 2002\^H root@TPC-C2-32:/us2&obj/usb\^Ks2c-scer' to stop...stopped
syncing disks... 1
done
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RC #9: Thu Jun 13 23:20:26 EDT 2002
root@TPC-C2-32:/usr/obj/usr/src/sys/TPC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (1996.60-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 1073217536 (1048064K bytes)
avail memory = 1039474688 (1015112K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 24 pins in IOAPIC #1
Programming 24 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 6, version: 0x00050014, at 0xfee00000
cpu2 (AP): apic id: 1, version: 0x00050014, at 0xfee00000
cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178020, at 0xfec00000
io1 (APIC): apic id: 3, version: 0x00178020, at 0xfec80000
io2 (APIC): apic id: 4, version: 0x00178020, at 0xfec80400
Preloaded elf kernel "kernel" at 0xc041e000.
netsmb_dev: loaded
md0: Malloc disk
Using $PIR table, 24 entries at 0xc00fde40
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 7
IOAPIC #0 intpin 18 -> irq 10
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on pci1
IOAPIC #2 intpin 0 -> irq 11
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5701 Gigabit Ethernet> mem 0xfc200000-0xfc20ffff irq 11 at device 1.0 on pci2
bge0: Ethernet address: 00:04:76:dd:2c:d0
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on pci1
IOAPIC #1 intpin 4 -> irq 16
IOAPIC #1 intpin 5 -> irq 17
IOAPIC #1 intpin 7 -> irq 18
pci3: <PCI bus> on pcib3
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2000-0x20ff mem 0xfc340000-0xfc340fff irq 16 at device 2.0 on pci3
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x2400-0x24ff mem 0xfc341000-0xfc341fff irq 17 at device 2.1 on pci3
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.3.8> port 0x2800-0x281f mem 0xfc300000-0xfc31ffff,0xfc320000-0xfc33ffff irq 18 at device 4.0 on pci3
em0: Speed:100 Mbps Duplex:Full
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1400-0x141f irq 2 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1420-0x143f irq 7 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x1440-0x145f irq 10 at device 29.2 on pci0
uhci2: (New UHCI DeviceId=0x24878086)
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: (0x24878086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pcib4: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 17 -> irq 19
pci4: <PCI bus> on pcib4
pci4: <ATI Mach64-GR graphics accelerator> at 1.0 irq 2
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x3400-0x343f mem 0xfc420000-0xfc43ffff,0xfc401000-0xfc401fff irq 19 at device 2.0 on pci4
fxp0: Ethernet address 00:30:48:12:33:d2
inphy0: <i82555 10/100 media interface> on miibus1
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=2480)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1460-0x146f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ichsmb0: <Intel 82801CA (ICH3) SMBus controller> port 0x1100-0x111f irq 0 at device 31.3 on pci0
pci_cfgintr_search: linked (61) to configured irq 19 at 4:2:0
pci_cfgintr: 0:31 INTB routed to irq 19
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus general purpose I/O> on smbus0
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xce800-0xcffff,0xd0000-0xd0fff,0xd8000-0xdbfff,0xdc000-0xdffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
pcf0: <PCF8584 I2C bus controller> at port 0x320-0x321 irq 5 on isa0
iicbus0: <Philips I2C bus> on pcf0 addr 0xaa
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to accept, logging disabled
BRIDGE 020214 loaded
DUMMYNET initialized (011031)
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
acd0: CDROM <MATSHITA CR-177> at ata1-master PIO4
Waiting 2 seconds for SCSI devices to settle
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <SUPER GEM318 0> Fixed Processor SCSI-2 device
pass2: 3.300MB/s transfers
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST318452LC 0003> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST318452LC 0003> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
Mounting root from ufs:/dev/da0s1a
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
da0s2: cannot find label (no disk label)
===============================================================================
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?FE045D4D9F7AED4CBFF1B3B813C8533767646A>