Date: Mon, 09 Dec 2002 17:39:20 -0800 From: oliver <opml@terraflux.com> To: Andrew Gallatin <gallatin@cs.duke.edu> Cc: <freebsd-alpha@freebsd.org>, "Schroeder, Aaron" <Aaron.Schroeder@qg.com> Subject: Re: AlphaServer1200 (5305), FBSD4.7 and Symbios53C875 Message-ID: <BA1A85C8.58D%opml@terraflux.com> In-Reply-To: <15861.16028.679747.646378@grasshopper.cs.duke.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
Drew,
Here is your boot -v; I also included a SRM show device.
<SNIP>
OK boot -v
\|/-\|/Entering /boot/kernel/kernel at 0xfffffc000033a510...
sio1: gdb debugging port
Unrecognized boot flag '0'.
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RC1 #0: Mon Dec 9 16:05:50 PST 2002
opi@carmen.terraflux.net:/usr/src/sys/alpha/compile/CARMEN
Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc000073a000.
AlphaServer 4100
DIGITAL Server 5000 Model 5305 6533A 5/533 4MB, 531MHz
8192 byte page size, 2 processors.
CPU: EV56 (21164A) major=7 minor=2 extensions=0x1<BWX>
OSF PAL rev: 0x4000200020117
real memory = 534757376 (509 MB)
Physical memory chunk(s):
0x0075c000 - 0x0fffffff, 260718592 bytes (31826 pages)
0x20000000 - 0x2fff3fff, 268386304 bytes (32762 pages)
avail memory = 508575744 (485 MB)
smp_start_secondary: starting cpu 1
smp_start_secondary: cpu 1 started
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
Initializing GEOMetry subsystem
random: <entropy source>
null: <null device, zero device>
mem: <memory & I/O>
mcbus0: <MCBUS Backplane Bus>
pcib0: <MCPCIA PCI Adapter> at mcbus0 gid 7 mid 5
pcib0: Horse Revision 3, Left Handed Saddle Revision 0, CAP Revision 2
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 4, range 32, base 01ffee00, size 8, enabled
map[14]: type 1, range 32, base 07cfef00, size 8, enabled
found-> vendor=0x1000, dev=0x0001, revid=0x02
bus=0, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0147, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0xff (7650 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=4
found-> vendor=0x1011, dev=0x0024, revid=0x02
bus=0, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
illegal PCI extended capability offset 8266240
map[10]: type 1, range 32, base 07cff000, size 12, enabled
map[14]: type 4, range 32, base 01ffef00, size 6, enabled
map[18]: type 1, range 32, base 07e00000, size 20, enabled
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=16
sym0: <810> port 0x1ffee00-0x1ffeeff mem 0x7cfef00-0x7cfefff irq 4 at device
1.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using NCR-generic firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/c8/00/00/08/00
sym0: Delay (GEN=11): 266 msec, 33414 KHz
sym0: Delay (GEN=11): 283 msec, 31407 KHz
sym0: Delay (GEN=11): 282 msec, 31518 KHz
sym0: interrupting at IRQ 0x10 intA (vec 0xb40)
pcib2: <PCI-PCI bridge> at device 2.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x82f0f000-0x47fffff
pcib2: memory decode 0x7d00000-0x7dfffff
pcib2: prefetched decode 0x80000000-0x7fffffff
pci2: <PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 4, range 32, base 01fffd00, size 8, enabled
map[14]: type 1, range 32, base 07d9dd00, size 8, enabled
map[18]: type 1, range 32, base 07d9e000, size 13, enabled
found-> vendor=0x1000, dev=0x000f, revid=0x04
bus=2, slot=0, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0200, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=8
map[10]: type 4, range 32, base 01fffe00, size 8, enabled
map[14]: type 1, range 32, base 07d9de00, size 8, enabled
map[18]: type 1, range 32, base 07d9f000, size 12, enabled
found-> vendor=0x1000, dev=0x000f, revid=0x04
bus=2, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0200, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=9
map[10]: type 4, range 32, base 01ffff00, size 7, enabled
map[14]: type 1, range 32, base 07d9df00, size 7, enabled
found-> vendor=0x1011, dev=0x0009, revid=0x22
bus=2, slot=2, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0280, cachelnsz=16 (dwords)
lattimer=0xff (7650 ns), mingnt=0x14 (5000 ns), maxlat=0x28 (10000 ns)
intpin=a, irq=10
sym1: <875> port 0x1fffd00-0x1fffdff mem
0x7d9e000-0x7d9ffff,0x7d9dd00-0x7d9ddff irq 8 at device 0.0 on pci2
pcib2: device sym1 requested decoded memory range 0x7d9dd00-0x7d9ddff
pcib2: device sym1 requested decoded memory range 0x7d9e000-0x7d9ffff
sym1: Delay (GEN=11): 242 msec, 36728 KHz
sym1: Delay (GEN=11): 227 msec, 39155 KHz
sym1: Delay (GEN=11): 227 msec, 39155 KHz
sym1: chip clock is 39155KHz
sym1: clock multiplier assumed
sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/80/01/08/24
sym1: Delay (GEN=11): 250 msec, 35553 KHz
sym1: Delay (GEN=11): 282 msec, 31518 KHz
sym1: Delay (GEN=11): 283 msec, 31407 KHz
sym1: interrupting at IRQ 0x0 intA (vec 0xb80)
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
sym2: <875> port 0x1fffe00-0x1fffeff mem
0x7d9f000-0x7d9ffff,0x7d9de00-0x7d9deff irq 9 at device 1.0 on pci2
pcib2: device sym2 requested decoded memory range 0x7d9de00-0x7d9deff
pcib2: device sym2 requested decoded memory range 0x7d9f000-0x7d9ffff
sym2: failed to allocate RAM resources
device_probe_and_attach: sym2 attach returned 6
de0: <Digital 21140A Fast Ethernet> port 0x1ffff00-0x1ffff7f mem
0x7d9df00-0x7d9df7f irq 10 at device 2.0 on pci2
pcib2: device de0 requested decoded memory range 0x7d9df00-0x7d9df7f
de0: interrupting at IRQ 0x0 intA (vec 0xb80)
de0: 21140A [10-100Mb/s] pass 2.2
de0: address 00:06:2b:00:0c:c5
de0: enabling 10baseT port
de0: bpf attached
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1ffef00-0x1ffef3f mem
0x7e00000-0x7efffff,0x7cff000-0x7cfffff irq 16 at device 4.0 on pci0
fxp0: using memory space register mapping
fxp0: interrupting at IRQ 0x8 intA (vec 0xc00)
fxp0: Ethernet address 00:90:27:8e:5c:13
fxp0: PCI IDs: 8086 1229 8086 000c 0008
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
pcib1: <MCPCIA PCI Adapter> at mcbus0 gid 7 mid 4
pcib1: Horse Revision 3, Left Handed Saddle Revision 0, CAP Revision 2
pci1: <PCI bus> on pcib1
pci1: physical bus=0
found-> vendor=0x8086, dev=0x0482, revid=0x15
bus=0, slot=1, func=0
class=00-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0xf8 (7440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 04000000, size 26, enabled
found-> vendor=0x5333, dev=0x8811, revid=0x44
bus=0, slot=2, func=0
class=88-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x8800, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x88 (34000 ns)
eisab0: <PCI-EISA bridge> at device 1.0 on pci1
isa0: <ISA bus> on eisab0
pci1: <unknown> at device 2.0 (no driver attached)
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000
ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0
ata0: interrupting at ISA irq 14
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata1 at port 0x376,0x170-0x177 irq 15 on isa0
ata1: interrupting at ISA irq 15
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd: the current kbd controller command byte 0023
atkbd: keyboard ID 0x83ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: interrupting at ISA irq 1
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 532800524 Hz (firmware 531914893 Hz)
i8254 clock: 1193194 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppc0: interrupting at ISA irq 7
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio1: interrupting at ISA irq 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 a0 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 a0 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
isa_probe_children: probing PnP devices
procfs registered
Timecounters tick every 0.833 msec
Timecounter "i8254" frequency 1193182 Hz
lo0: bpf attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
(probe5:sym0:0:5:0): Retrying Command
(probe0:sym0:0:0:0): Retrying Command
(probe5:sym0:0:5:0): error 22
(probe5:sym0:0:5:0): Unretryable Error
(probe7:sym1:0:0:0): Retrying Command
(probe8:sym1:0:1:0): Retrying Command
pass0 at sym0 bus 0 target 0 lun 0
pass0: <QUANTUM XP34550S LXQ1> Fixed Direct Access SCSI-2 device
pass0: Serial Number PCB=2011303001 ; HDA=184630210680
pass0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
pass1 at sym0 bus 0 target 5 lun 0
pass1: <DEC RRD46 (C) DEC 1337> Removable CD-ROM SCSI-2 device
pass1: 10.000MB/s transfers (10.000MHz, offset 8)
pass2 at sym1 bus 0 target 0 lun 0
pass2: <SEAGATE ST34371W 0702> Fixed Direct Access SCSI-2 device
pass2: Serial Number JDV300100FBG8K
pass2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
pass3 at sym1 bus 0 target 1 lun 0
pass3: <Quantum XP34550J LYJ2> Fixed Direct Access SCSI-2 device
pass3: Serial Number 184732250537
pass3: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing
Enabled
da1 at sym1 bus 0 target 0 lun 0
da1: <SEAGATE ST34371W 0702> Fixed Direct Access SCSI-2 device
da1: Serial Number JDV300100FBG8K
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da1: 4095MB (8388314 512 byte sectors: 255H 63S/T 522C)
da2 at sym1 bus 0 target 1 lun 0
da2: <Quantum XP34550J LYJ2> Fixed Direct Access SCSI-2 device
da2: Serial Number 184732250537
da2: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing
Enabled
da2: 4095MB (8388315 512 byte sectors: 255H 63S/T 522C)
da0 at sym0 bus 0 target 0 lun 0
da0: <QUANTUM XP34550S LXQ1> Fixed Direct Access SCSI-2 device
da0: Serial Number PCB=2011303001 ; HDA=184630210680
da0: 10.000MB/s transfers (10.000MHz, offset 8), Tagged Queueing Enabled
da0: 4341MB (8890760 512 byte sectors: 255H 63S/T 553C)
cd0 at sym0 bus 0 target 5 lun 0
cd0: <DEC RRD46 (C) DEC 1337> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 8)
cd0: cd present [517192 x 512 byte records]
GEOM: new disk da0
GEOM: new disk da1
GEOM: new disk da2
release_aps: releasing secondary CPUs
SMP: AP CPU #1 Launched!
GEOM: Add da0 hot[0] start 64 length 276 end 339
GEOM: Configure da0a, start 0 length 134217728 end 134217727
GEOM: Configure da0b, start 134217728 length 1069514752 end 1203732479
GEOM: Configure da0c, start 0 length 4552069120 end 4552069119
GEOM: Configure da0d, start 1203732480 length 268435456 end 1472167935
GEOM: Configure da0e, start 1472167936 length 268435456 end 1740603391
GEOM: Configure da0f, start 1740603392 length 2811465728 end 4552069119
GEOM: Add da1 hot[0] start 64 length 276 end 339
GEOM: Configure da1c, start 0 length 4294816768 end 4294816767
GEOM: Add da2 hot[0] start 64 length 276 end 339
GEOM: Configure da2c, start 0 length 4294817280 end 4294817279
Mounting root from ufs:/dev/da0a
start_init: trying /sbin/init
hw.bus.devctl_disable: 0 -> 1
Entropy harvesting: interrupts ethernet point_to_point.
swapon: adding /dev/da0b as swap device
Starting file system checks:
/dev/da0a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0a: clean, 17325 free (821 frags, 2063 blocks, 1.3% fragmentation)
/dev/da0e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0e: clean, 128918 free (14 frags, 16113 blocks, 0.0% fragmentation)
/dev/da0f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0f: clean, 966161 free (22833 frags, 117916 blocks, 1.7%
fragmentation)
/dev/da0d: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0d: clean, 128797 free (37 frags, 16095 blocks, 0.0% fragmentation)
Doing initial network setup: hostname.
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 192.168.0.25 netmask 0xffffff00 broadcast 192.168.0.255
inet6 fe80::290:27ff:fe8e:5c13%fxp0 prefixlen 64 tentative scopeid 0x2
ether 00:90:27:8e:5c:13
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
add net default: gateway 192.168.0.20
Additional routing options:.
Mounting NFS file systems:.
Starting syslogd.
Dec 9 17:27:09 carmen syslogd: kernel boot file is /boot/kernel/kernel
ELF ldconfig path: /usr/lib /usr/lib/compat
Starting local daemons:.
Updating motd.
Starting sshd.
Initial alpha initialization:.
Additional ABI support:.
Local package initialization:.
Additional TCP options:.
Starting cron.
Starting background file system checks.
Mon Dec 9 17:27:34 PST 2002
FreeBSD/alpha (carmen.terraflux.net) (ttyd0)
login:
<SNIP>
<SNIP>
DIGITAL Server 5000 Model 5305 6533A Console V6.0-4, 10-MAY-2001 10:11:42
P00>>>show device
polling ncr0 (NCR 53C810) slot 1, bus 0 PCI, hose 1 SCSI Bus ID 7
dka0.0.0.1.1 DKA0 QUANTUM XP34550S LXQ1
dka500.5.0.1.1 DKA500 RRD46 1337
polling ncr1 (NCR 53C875) slot 0, bus 2 PCI, hose 1 SCSI Bus ID 7
dkb0.0.0.2000.1 DKB0 SEAGATE ST34371W 0702
dkb100.1.0.2000.1 DKB100 Quantum XP34550J LYJ2
polling ncr2 (NCR 53C875) slot 1, bus 2 PCI, hose 1 SCSI Bus ID 7
polling floppy0 (FLOPPY) PCEB - XBUS hose 0
dva0.0.0.1000.0 DVA0 RX23
polling tulip0 (DECchip 21140-AA) slot 2, bus 2 PCI, hose 1
ewa0.0.0.2002.1 00-06-2B-00-0C-C5 Twisted-Pair
polling ei0 (Intel 8255x Ethernet) slot 4, bus 0 PCI, hose 1
eia0.0.0.4.1 00-90-27-8E-5C-13 Twisted-Pair
P00>>>
<SNIP>
Cheers,
Oliver
On 12/9/02 17:08, "Andrew Gallatin" <gallatin@cs.duke.edu> wrote:
>
> oliver writes:
>> Drew,
>>
>> Update: I installed the more recent fBSD 5.0 RC-1 (iso) on the temporary
>> disk. This time, the two channles on the 875 card appeared recognized (at
>> least sym1, but what's with the "faqiled to alloc ram" for sym2 (dmesg)?).
>>
>
>
> I"m not sure what's causing this. When you get the machine installed,
> please send the output from a verbose boot (hit the space bar at the
> boot loaders 9..8..7... countdown and type boot -v)
>
> The most likely scenario is that the firmware has lied about the
> memory behind the 21x52 pci-pci bridge or set something up a little
> bit not to our liking. From the dmesg you sent, things look OK, but
> we cannot see what memory ranges the bridge is passing from that.
>
> Drew
>
>
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BA1A85C8.58D%opml>