Date: Thu, 28 Dec 2006 08:56:01 -0500 From: John Baldwin <jhb@freebsd.org> To: "Sergey Lyubka" <valenok@gmail.com> Cc: freebsd-hardware@freebsd.org Subject: Re: Dell Poweredge 1950, boot problem Message-ID: <200612280856.01539.jhb@freebsd.org> In-Reply-To: <72c3a9570612280527s5e586b52hf76bd52132d93235@mail.gmail.com> References: <72c3a9570612180904t6dba47das5ea0cbcc34cd2b4b@mail.gmail.com> <200612271939.59771.jhb@freebsd.org> <72c3a9570612280527s5e586b52hf76bd52132d93235@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thursday 28 December 2006 08:27, Sergey Lyubka wrote: > Right, here is the dmesg where hang did not happen (usually happens though): Can you use a serial console to get the 'boot -v' dmesg when the hang does occur? Also, when the hang occurs, can you break into ddb and run 'show intrcnt'? > Copyright (c) 1992-2006 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 6.2-RC1 #0: Thu Nov 16 05:12:08 UTC 2006 > root@opus.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Xeon(TM) CPU 3.00GHz (2995.51-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf64 Stepping = 4 > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > Features2=0xe4bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,CNTX-ID,CX16,<b14>,<b15>> > AMD Features=0x20100000<NX,LM> > AMD Features2=0x1<LAHF> > Cores per package: 2 > Logical CPUs per core: 2 > real memory = 1073381376 (1023 MB) > avail memory = 1041211392 (992 MB) > ACPI APIC Table: <DELL PE_SC3 > > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 2 > cpu2 (AP): APIC ID: 4 > cpu3 (AP): APIC ID: 6 > ioapic0: Changing APIC ID to 8 > ioapic1: Changing APIC ID to 9 > ioapic1: WARNING: intbase 64 != expected base 24 > ioapic0 <Version 2.0> irqs 0-23 on motherboard > ioapic1 <Version 2.0> irqs 64-87 on motherboard > kbd1 at kbdmux0 > ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > acpi0: <DELL PE_SC3> on motherboard > acpi0: Power Button (fixed) > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > cpu0: <ACPI CPU> on acpi0 > cpu1: <ACPI CPU> on acpi0 > cpu2: <ACPI CPU> on acpi0 > cpu3: <ACPI CPU> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0 > pci5: <ACPI PCI bus> on pcib1 > pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci5 > pci6: <ACPI PCI bus> on pcib2 > pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci6 > pci7: <ACPI PCI bus> on pcib3 > pcib4: <ACPI PCI-PCI bridge> at device 1.0 on pci6 > pci9: <ACPI PCI bus> on pcib4 > pcib5: <PCI-PCI bridge> at device 0.3 on pci5 > pci10: <PCI bus> on pcib5 > pcib6: <ACPI PCI-PCI bridge> at device 3.0 on pci0 > pci1: <ACPI PCI bus> on pcib6 > pcib7: <ACPI PCI-PCI bridge> at device 0.0 on pci1 > pci2: <ACPI PCI bus> on pcib7 > mpt0: <LSILogic SAS/SATA Adapter> port 0xec00-0xecff mem > 0xfddfc000-0xfddfffff,0xfdde0000-0xfddeffff irq 64 at device 8.0 on > pci2 > mpt0: [GIANT-LOCKED] > mpt0: MPI Version=1.5.12.0 > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > mpt0: mpt_cam_event: 0x12 > mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). > mpt0: mpt_cam_event: 0x16 > mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). > pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0 > pci11: <ACPI PCI bus> on pcib8 > bge0: <Broadcom BCM5750 C1, ASIC rev. 0x4201> mem > 0xfd8f0000-0xfd8fffff irq 16 at device 0.0 on pci11 > miibus0: <MII bus> on bge0 > brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > 1000baseTX-FDX, auto > bge0: Ethernet address: 00:10:18:19:68:ae > pcib9: <PCI-PCI bridge> at device 5.0 on pci0 > pci12: <PCI bus> on pcib9 > pcib10: <ACPI PCI-PCI bridge> at device 6.0 on pci0 > pci13: <ACPI PCI bus> on pcib10 > pcib11: <PCI-PCI bridge> at device 7.0 on pci0 > pci14: <PCI bus> on pcib11 > pcib12: <ACPI PCI-PCI bridge> at device 28.0 on pci0 > pci3: <ACPI PCI bus> on pcib12 > uhci0: <UHCI (generic) USB controller> port 0xcce0-0xccff irq 21 at > device 29.0 on pci0 > uhci0: [GIANT-LOCKED] > usb0: <UHCI (generic) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <UHCI (generic) USB controller> port 0xccc0-0xccdf irq 20 at > device 29.1 on pci0 > uhci1: [GIANT-LOCKED] > usb1: <UHCI (generic) USB controller> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhci2: <UHCI (generic) USB controller> port 0xcca0-0xccbf irq 21 at > device 29.2 on pci0 > uhci2: [GIANT-LOCKED] > usb2: <UHCI (generic) USB controller> on uhci2 > usb2: USB revision 1.0 > uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdf00000-0xfdf003ff > irq 21 at device 29.7 on pci0 > ehci0: [GIANT-LOCKED] > usb3: EHCI version 1.0 > usb3: companion controllers, 2 ports each: usb0 usb1 usb2 > usb3: <EHCI (generic) USB 2.0 controller> on ehci0 > usb3: USB revision 2.0 > uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub3: 6 ports with 6 removable, self powered > uhub4: vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 2 > uhub4: multiple transaction translators > uhub4: 4 ports with 4 removable, self powered > ukbd0: Dell Dell USB Keyboard, rev 1.10/3.01, addr 3, iclass 3/1 > kbd2 at ukbd0 > pcib13: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci15: <ACPI PCI bus> on pcib13 > pci15: <display, VGA> at device 13.0 (no driver attached) > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel 63XXESB2 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on > pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 > fdc0: does not respond > device_attach: fdc0 attach returned 6 > sio0: configured irq 0 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: configured irq 0 not in bitmap of probed irqs 0 > sio0: port may not be enabled > fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 > fdc0: does not respond > device_attach: fdc0 attach returned 6 > sio0: configured irq 0 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: configured irq 0 not in bitmap of probed irqs 0 > sio0: port may not be enabled > pmtimer0 on isa0 > orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xec000-0xeffff on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > ppc0: parallel port not found. > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 or not responding > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounters tick every 1.000 msec > acd0: CDROM <TEAC CD-ROM CD-224E-N/3.AB> at ata0-master UDMA33 > ses0 at mpt0 bus 0 target 8 lun 0 > ses0: <DP BACKPLANE 1.00> Fixed Enclosure Services SCSI-5 device > ses0: 300.000MB/s transfers > ses0: SCSI-3 SES Device > SMP: AP CPU #1 Launched! > SMP: AP CPU #2 Launched! > SMP: AP CPU #3 Launched! > da0 at mpt0 bus 0 target 0 lun 0 > da0: <FUJITSU MAX3036RC D206> Fixed Direct Access SCSI-3 device > da0: 300.000MB/s transfers, Tagged Queueing Enabled > da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) > Trying to mount root from ufs:/dev/da0s1a > bge0: link state changed to UP > > > This time `sysctl hw.ncpu` shows 4. This is because I have disabled > CPU features (hardware prefetch, virtualization, logical processor, > etc). If these features enabled, hw.ncpu is 8. The box is 2 x Xeon > Dell 1950. > -- John Baldwin
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200612280856.01539.jhb>