From owner-freebsd-stable Sun Oct 15 22:58:14 2000 Delivered-To: freebsd-stable@freebsd.org Received: from mail.roomlinx.com (roomlinx.com [209.153.237.60]) by hub.freebsd.org (Postfix) with ESMTP id 0688037B670 for ; Sun, 15 Oct 2000 22:58:09 -0700 (PDT) Received: from leonardo [209.52.105.28] by mail.roomlinx.com (SMTPD32-6.00) id AA28915011A; Sun, 15 Oct 2000 23:05:28 +0100 From: "Wyness Casama" To: Subject: vr0: watchdog timeout Date: Sun, 15 Oct 2000 22:59:29 -0700 Message-ID: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit X-Priority: 3 (Normal) X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook IMO, Build 9.0.2416 (9.0.2910.0) X-MimeOLE: Produced By Microsoft MimeOLE V5.50.4133.2400 Importance: Normal Sender: owner-freebsd-stable@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Hi all, I've seen this issue posted in a few places over the net where the DLink DFE-530TX (Via Rhine II/whatever) card drops out during xfers (anything larger than 100k) in FBSD 4.x. Of course, I have a DFE-530TX that's doing that @ this moment as well. With a 6-pack of these cards sitting on my desk, I'm wondering if this issue could be resolved OR if I should send the cards back. Attache is a dmesg output of a recent boot which may shed some light on what I'm doing wrong. Mind you, I haven't managed to CVSup my system because it's crapping out after a few minutes w/ watchdog timeouts. ------------[ DMESG OUTPUT AS FOLLOWS: ]--------------- Copyright (c) 1992-2000 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.1.1-STABLE #0: Sun Oct 15 18:26:27 GMT 2000 root@thedyingsun.bctel.net:/usr/src/sys/compile/kernel_1.0.0 Timecounter "i8254" frequency 1193182 Hz CPU: AMD-K6(tm) 3D processor (501.14-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 Features=0x8021bf AMD Features=0x80000800 real memory = 67043328 (65472K bytes) config> en ata0 config> po ata0 0x1f0 config> ir ata0 14 config> f ata0 0 config> q avail memory = 62406656 (60944K bytes) Preloaded elf kernel "kernel" at 0xc02e4000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc02e40a8. K6-family MTRR support enabled (2 registers) md0: Malloc disk npx0: on motherboard npx0: INT 16 interface pcib0: on motherboard pci0: on pcib0 pcib2: at device 1.0 on pci0 pci1: on pcib2 pci1: at 0.0 irq 11 isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0xd000-0xd00f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 uhci0: port 0xd400-0xd41f irq 10 at device 7.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered atapci1: port 0xe800-0xe83f,0xe400-0xe403,0xe000-0xe007,0xdc00-0xdc03,0xd800-0xd807 mem 0xec000000-0xec01ffff irq 11 at device 8.0 on pci0 ata2: at 0xd800 on atapci1 ata3: at 0xe000 on atapci1 xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xec00-0xec7f mem 0xec020000-0xec02007f irq 12 at device 11.0 on pci0 xl0: Ethernet address: 00:50:04:88:24:60 miibus0: on xl0 xlphy0: <3Com internal media interface> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pcib1: on motherboard pci2: on pcib1 fdc0: at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: at port 0x60,0x64 on isa0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode plip0: on ppbus0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 ad0: 3079MB [6256/16/63] at ata0-master using WDMA2 ad4: 78167MB [158816/16/63] at ata2-master using UDMA100 ad5: 78167MB [158816/16/63] at ata2-slave using UDMA100 acd0: CDROM at ata0-slave using PIO4 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message