Date: Thu, 12 Oct 2006 17:08:16 +0200 From: Bruno Ducrot <ducrot@poupinou.org> To: John Baldwin <jhb@freebsd.org> Cc: freebsd-mobile@freebsd.org Subject: Re: Acer Aspire 5672 and FreeBSD 6.2-beta1 Message-ID: <20061012150816.GW4945@poupinou.org> In-Reply-To: <200610100921.54233.jhb@freebsd.org> References: <20060930001213.a59d721c.torfinn.ingolfsen@broadpark.no> <200610091611.46706.jhb@freebsd.org> <20061010095205.GS4945@poupinou.org> <200610100921.54233.jhb@freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Oct 10, 2006 at 09:21:53AM -0400, John Baldwin wrote: > On Tuesday 10 October 2006 05:52, Bruno Ducrot wrote: > > On Mon, Oct 09, 2006 at 04:11:46PM -0400, John Baldwin wrote: > > > On Saturday 07 October 2006 15:03, Bruno Ducrot wrote: > > > > On Sat, Oct 07, 2006 at 06:46:42PM +0200, Torfinn Ingolfsen wrote: > > > > > On Sat, 07 Oct 2006 17:01:03 +0200 > > > > > Bruno Ducrot <ducrot@poupinou.org> wrote: > > > > > > > > > > > Thanks. The device do not have a BAR when acpi is enabled. We > > > > > > therefore have to enable one. I think just by poking aroud some pci > > > > > > config registers onto the pci bridge will do the trick. Your > > > > > > > > > > Ok. I'm wondering; will output from lspci under Linux help you get at > > > > > the info more easily? I have Xubuntu installed on a partition on this > > > > > machine, so it is easy for me to do that, if you wish. > > > > > > > > Well, I don't know if that will be helpful. Humm, maybe a dmesg? > > > > > > > > > > Looking at this datasheet I think we have to look more carrefully to > > > > > > register 0x04 (halfword), 0x20h, 0x24, 0x28 and 0x2c. > > > > > > Looking them both with and without acpi and comparing them will allows > > > > > > us to know hopefully how to enable the first BAR to the correct adress > > > > > > for your ethernet card. In short, if you can first boot without ACPI, > > > > > > then perform > > > > > > pciconf -r -h pci0:28:2 4 > > > > > > pciconf -r pci0:28:2 0x20 > > > > > > pciconf -r pci0:28:2 0x24 > > > > > > pciconf -r pci0:28:2 0x28 > > > > > > pciconf -r pci0:28:2 0x2c > > > > > > > > > > > > Also do a dump in order to check if something else might be needed: > > > > > > pciconf -r -b pci0:28:2 0:256 > > > > > > > > > > > > Boot with ACPI enabled: > > > > > > do the same pciconf stuff, then send me the output. > > > > > > > > > > Done. I've sent you the files via email, and also uploaded them to the > > > > > web page, in case anyone else wants them for some reason. Webpage: > > > > > http://tingox.googlepages.com/aceraspireas5672andfreebsd > > > > > > > > > > > After that, we should be able to correct your problem, either by > > > > > > 1- hacking the DSDT, > > > > > > OR > > > > > > 2- hacking pcib.c. > > > > > > (at your option). > > > > > > > > > > I think hacking the DSDT is the more politically correct option, but > > > > > either one will work for me. > > > > > > > > Ok. First remove device bge in your kernel config. For example create a > > > > config file with: > > > > > > > > >>> BEGIN > > > > include GENERIC > > > > ident MYKERNEL (or what you like) > > > > nodevice bge > > > > <<< END > > > > > > > > After rebuilding and installing your kernel, > > > > you can do something like that: > > > > > > > > pciconf -w pci0:28:2 0xd8 0x04110008 > > > > > > > > pciconf -w -h pci0:28:2 0x58 0x0000 > > > > > > > > pciconf -w pci0:28:2 0x24 0x0001fff1 > > > > pciconf -w pci0:28:2 0x20 0xc830c830 > > > > > > > > pciconf -w -h pci0:28:2 0x04 0x0007 > > > > > > > > > > > > After that, you should be able to kldload if_bge and report back if > > > > this work. In that case I will modify the DSDT so that you won't to > > > > worry about all of those pciconf stuff. > > > > > > You really shouldn't change BAR registers directly. First of all, the PCI > > > bus driver already knows how to allocate resources for a BAR if it is set > > > to 0 and when doing so will make sure to not allocate an address that > > > conflicts with another device. Secondly, a lot of PCI config registers are > > > cached in the ivars by the PCI bus, so it may not even read the values you > > > write into it (though writing those values will turn on the address decode > > > for the device, and if another device is using that address things will go > > > downhill quick). > > > > You are indeed right. The issue therefore seems to be, when ACPI is enabled, > > then the PCI bus driver doesn't set up correctly a BAR. > > FYI the bridge is one of the four PCIe embedded to an ICH-7. > > The PCI bus driver does the same thing regardless of ACPI. When the NIC driver > does its bus_alloc_resource() the PCI bus should then go allocate resources for > it. At this point you will probably want to get a boot -v so you can see what > the bus prints out when it first looks at the device first. If the BAR is > listed (but with a base of 0), then you will want to look at the stuff in > pci_alloc_resource(). > John, the relevant info. is (I think) : pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 pcib4: secondary bus 4 pcib4: subordinate bus 4 pcib4: I/O decode 0x0-0x0 pcib4: memory decode 0x0-0x0 pcib4: prefetched decode 0x0-0x0 pci4: <ACPI PCI bus> on pcib4 pci4: physical bus=4 found-> vendor=0x14e4, dev=0x169d, revid=0x21 bus=4, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit map[10]: type 1, range 64, base 00000000, size 16, memory disabled bge0: <Broadcom BCM5750 C1, ASIC rev. 0x4201> irq 18 at device 0.0 on pci4 pcib4: bge0 requested unsupported memory range 0x0-0xffffffff (decoding 0x0-0x0, 0x0-0x0) bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). bge0: couldn't map memory device_attach: bge0 attach returned 6 Sound like the PCI-PCI bridge is not setup correct to me at first. Cheers, -- Bruno Ducrot -- Which is worse: ignorance or apathy? -- Don't know. Don't care.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20061012150816.GW4945>