From owner-freebsd-mobile Mon Mar 27 13:45:24 2000 Delivered-To: freebsd-mobile@freebsd.org Received: from scaup.prod.itd.earthlink.net (scaup.prod.itd.earthlink.net [207.217.121.49]) by hub.freebsd.org (Postfix) with ESMTP id 5953137BB8A for ; Mon, 27 Mar 2000 13:45:21 -0800 (PST) (envelope-from prmoyer@mail.earthlink.net) Received: from mail.earthlink.net (ip112.wilmington3.de.pub-ip.psi.net [38.30.157.112]) by scaup.prod.itd.earthlink.net (8.9.3/8.9.3) with ESMTP id NAA17393; Mon, 27 Mar 2000 13:45:18 -0800 (PST) Message-Id: <200003272145.NAA17393@scaup.prod.itd.earthlink.net> From: "Philip R. Moyer" Reply-To: pmoyer@hyperon.com To: freebsd-mobile@freebsd.org Cc: woody@nosloop.com Subject: Re: CEM56 pccard.conf entry??? Date: Mon, 27 Mar 2000 16:45:33 -0500 Sender: owner-freebsd-mobile@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.org Back in November, Woody Poolson asked about a pccard.conf entry for the Xircom RealPort Ethernet 10/100 + Modem 56, aka CEM56. Nick Slager posted an entry that works for the Ethernet interface, but there were no followups for the modem. I've got one of these cards as well. It worked under 3.4-RELEASE+PAO, but it does not work under 4.0-STABLE with pccard. Soooo, does anyone have a working pccard.conf entry for the modem part of the card? I'm not familiar enough with pcmcia configurations to figure it out on my own. I've appended the dumpcis output for the card, if it helps any. Cheers, Phil Code 136 not found Code 136 not found code Unknown ignored code Manufacturer ID ignored Code 138 not found Code 138 not found code Unknown ignored Code 139 not found Code 139 not found code Unknown ignored Configuration data for card in slot 0 Tuple #1, code = 0x1 (Common memory descriptor), length = 2 000: 00 ff Common memory device information: Device number 1, type No device, WPS = OFF Speed = No speed, Memory block size = reserved, 32 units Tuple #2, code = 0x17 (Attribute memory descriptor), length = 2 000: 00 ff Attribute memory device information: Device number 1, type No device, WPS = OFF Speed = No speed, Memory block size = reserved, 32 units Tuple #3, code = 0x15 (Version 1 info), length = 59 000: 05 00 58 69 72 63 6f 6d 00 43 72 65 64 69 74 43 010: 61 72 64 20 45 74 68 65 72 6e 65 74 20 31 30 2f 020: 31 30 30 20 2b 20 4d 6f 64 65 6d 20 35 36 00 43 030: 45 4d 35 36 00 31 2e 30 30 00 ff Version = 5.0, Manuf = [Xircom],card vers = [CreditCard Ethernet 10/100 + Modem 56] Addit. info = [CEM56],[1.00] Tuple #4, code = 0x0 (Null tuple), length = 8 000: 33 dc eb 00 00 00 00 00 Tuple #5, code = 0x0 (Null tuple), length = 5 000: 05 01 0a 11 46 Tuple #6, code = 0x44 (Card init date), length = 4 000: 41 71 2e 28 Tuple #7, code = 0x1a (Configuration map), length = 5 000: 01 3f 80 ff 67 Reg len = 2, config register addr = 0xff80, last config = 0x3f Registers: XXX--XX- Tuple #8, code = 0x1b (Configuration entry), length = 20 000: e7 c1 9d 0f 55 4d 5d 4e e0 17 17 ea 60 e8 02 07 010: f0 bc 8e 20 Config index = 0x27(default) Interface byte = 0xc1 (I/O) +RDY/-BSY active, wait signal supported Vcc pwr: Nominal operating supply voltage: 5 x 1V Minimum operating supply voltage: 4.5 x 1V Maximum operating supply voltage: 5.5 x 1V Continuous supply current: 4.5 x 100mA Wait scale Speed = 1.2 x 10 ms RDY/BSY scale Speed = 1.2 x 10 ms Card decodes 23 address lines IRQ modes: IRQs: NMI IOCK BERR 0 1 2 4 8 9 10 12 Max twin cards = 0 Misc attr: (Power down supported) Tuple #9, code = 0x1b (Configuration entry), length = 7 000: 1f 08 ea 60 e8 03 07 Config index = 0x1f Card decodes 10 address lines, full 8/16 Bit I/O I/O address # 1: block start = 0x3e8 block length = 0x8 Tuple #10, code = 0x1b (Configuration entry), length = 7 000: 17 08 ea 60 f8 02 07 Config index = 0x17 Card decodes 10 address lines, full 8/16 Bit I/O I/O address # 1: block start = 0x2f8 block length = 0x8 Tuple #11, code = 0x1b (Configuration entry), length = 7 000: 0f 08 ea 60 f8 03 07 Config index = 0xf Card decodes 10 address lines, full 8/16 Bit I/O I/O address # 1: block start = 0x3f8 block length = 0x8 Tuple #12, code = 0x1b (Configuration entry), length = 3 000: 3f 08 63 Config index = 0x3f Card decodes 3 address lines, full 8/16 Bit I/O Tuple #13, code = 0x21 (Functional ID), length = 2 000: 02 00 Serial port/modem Tuple #14, code = 0x22 (Functional EXT), length = 4 000: 00 02 0f 5c Serial interface extension: 16550 UART, Parity - Space,Mark,Odd,Even, Tuple #15, code = 0x22 (Functional EXT), length = 12 000: 02 06 00 3f 1c 03 03 0f 07 00 01 b5 Data modem services available: Tuple #16, code = 0x22 (Functional EXT), length = 8 000: 13 06 00 0b 00 02 00 b5 Tuple #17, code = 0x21 (Functional ID), length = 2 000: 06 00 Network/LAN adapter Tuple #18, code = 0x22 (Functional EXT), length = 8 000: 04 06 00 10 a4 eb dc 33 Voice services available: Tuple #19, code = 0x0 (Null tuple), length = 12 000: 39 30 30 34 41 42 45 42 44 43 33 33 Tuple #20, code = 0x0 (Null tuple), length = 4 000: 01 00 00 00 Tuple #21, code = 0x14 (No link), length = 0 Tuple #22, code = 0xff (Terminator), length = 0 2 slots found To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message