Date: 06 Nov 2002 23:45:06 +0100 From: Frode Nordahl <frode@nordahl.net> To: "M. Warner Losh" <imp@bsdimp.com> Cc: current@FreeBSD.ORG Subject: Re: Some problems with Orinoco card in -CURRENT Message-ID: <1036622707.750.2.camel@samwise.xu.nordahl.net> In-Reply-To: <20021106.152802.31977531.imp@bsdimp.com> References: <1036617037.581.4.camel@samwise.xu.nordahl.net> <20021106.152802.31977531.imp@bsdimp.com>
next in thread | previous in thread | raw e-mail | index | archive | help
--=-b22uwgqH8uYp9pxr2U6T
Content-Type: text/plain
Content-Transfer-Encoding: 7bit
Hey,
On Wed, 2002-11-06 at 23:28, M. Warner Losh wrote:
> Strange. OLDCARD or NEWCARD? Send me a full dmesg for each case,
> since it is likely some resource conflict or another. I do what
> you've described hundreds of times over the past few months, so it has
> to be something weird with your computer.
My computer might be wierd :) I have a problem with the BIOS not
initializing the memory correctly (I often see dmesg output and post
morten messages from previous boot).
So I even did a __cold__ reboot (unplug AC, remove battery for a while)
before this dmesg (boot -v).
I only hav NEWCARD kernel available at this time, will post a OLDCARD
boot -v ASAP.
(See attachment)
> Warner.
>
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-current" in the body of the message
--=-b22uwgqH8uYp9pxr2U6T
Content-Disposition: attachment; filename=NEWCARD_dmesg.txt
Content-Transfer-Encoding: quoted-printable
Content-Type: text/plain; name=NEWCARD_dmesg.txt; charset=ISO-8859-1
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Mon Nov 4 14:23:41 CET 2002
frode@samwise.xu.nordahl.net:/usr/src/sys/i386/compile/SAMWISE
Preloaded elf kernel "/boot/kernel/kernel" at 0xc05bc000.
Preloaded elf module "/boot/kernel/snd_via82c686.ko" at 0xc05bc0b4.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc05bc168.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05bc214.
Calibrating clock(s) ... TSC clock: 1193637253 Hz, i8254 clock: 1193135 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 1193693787 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1193.69-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x6b1 Stepping =3D 1
Features=3D0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,=
CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory =3D 234881024 (229376K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x005e3000 - 0x0deeffff, 227594240 bytes (55565 pages)
0x0df00000 - 0x0dff7fff, 1015808 bytes (248 pages)
avail memory =3D 221925376 (216724K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f7290
bios32: Entry =3D 0xfd6f0 (c00fd6f0) Rev =3D 0 Len =3D 1
pcibios: PCI BIOS entry at 0xfd6f0+0x11e
pnpbios: Found PnP BIOS data at 0xc00f72f0
pnpbios: Entry =3D f0000:97e0 Rev =3D 1.0
Other BIOS signatures found:
Initializing GEOMetry subsystem
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
VESA: information block
56 45 53 41 00 02 73 80 00 c0 01 00 00 00 22 00=20
00 01 ef 01 00 01 57 79 00 c0 68 79 00 c0 70 79=20
00 c0 00 01 01 01 03 01 05 01 07 01 0e 01 0f 01=20
11 01 12 01 14 01 15 01 17 01 18 01 1a 01 1b 01=20
VESA: 39 mode(s) found
VESA: v2.0, 31680k memory, flags:0x1, mode table:0xc04c36a2 (1000022)
VESA: S3 Incorporated. Twister BIOS
VESA: S3 Incorporated. VBE 2.0 Rev 1.1
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT > on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=3D0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=3D060000] [hdr=3D00] is there (id=3D06051106)
Using $PIR table, 8 entries at 0xc00fdf40
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 0 A 0x56 3 4 5 6 7 9 10 11 12 14 15
embedded 0 0 B 0x56 3 4 5 6 7 9 10 11 12 14 15
embedded 0 0 C 0x57 3 4 5 6 7 9 10 11 12 14 15
embedded 0 0 D 0x55 3 4 5 6 7 9 10 11 12 14 15
embedded 0 7 C 0x56 5
embedded 0 7 D 0x57 11
embedded 0 4 A 0x55 10
embedded 0 4 B 0x56 11
embedded 0 13 A 0x56 5
embedded 0 1 A 0x55 10
embedded 1 0 A 0x55 10
embedded 0 16 A 0x57 11
embedded 0 16 B 0x56 11
embedded 0 17 A 0x56 11
embedded 0 17 B 0x57 11
acpi0: power button is handled as a fixed feature programming model.
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
ACPI timer looks GOOD min =3D 1, max =3D 2, width =3D 2
Timecounter "ACPI-fast" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 0.1.0
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 0.4.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.4.1
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 0.7.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.7.1
\\_SB_.PCI0.PIB_.LNKC irq 5: [ 5 9 10 11] low,level,sharable 0.7.2
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 11] low,level,sharable 0.7.3
\\_SB_.PCI0.PIB_.LNKC irq 5: [ 5 9 10 11] low,level,sharable 0.13.0
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 11] low,level,sharable 0.16.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.16.1
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.17.0
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 11] low,level,sharable 0.17.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 0.1.0
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 0.4.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.4.1
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 0.7.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.7.1
\\_SB_.PCI0.PIB_.LNKC irq 5: [ 5 9 10 11] low,level,sharable 0.7.2
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 11] low,level,sharable 0.7.3
\\_SB_.PCI0.PIB_.LNKC irq 5: [ 5 9 10 11] low,level,sharable 0.13.0
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 11] low,level,sharable 0.16.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.16.1
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 11] low,level,sharable 0.17.0
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 11] low,level,sharable 0.17.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=3D0
map[10]: type 3, range 32, base ec000000, size 26, enabled
found-> vendor=3D0x1106, dev=3D0x0605, revid=3D0x00
bus=3D0, slot=3D0, func=3D0
class=3D06-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0006, statreg=3D0xa210, cachelnsz=3D0 (dwords)
lattimer=3D0x08 (240 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=3D0x1106, dev=3D0x8605, revid=3D0x00
bus=3D0, slot=3D1, func=3D0
class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
cmdreg=3D0x0007, statreg=3D0x2230, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x0c (3000 ns), maxlat=3D0x00 (0 ns)
found-> vendor=3D0x1217, dev=3D0x6933, revid=3D0x01
bus=3D0, slot=3D4, func=3D0
class=3D06-07-00, hdrtype=3D0x02, mfdev=3D1
cmdreg=3D0x0003, statreg=3D0x0410, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x80 (32000 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D255
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=3D0x1217, dev=3D0x6933, revid=3D0x01
bus=3D0, slot=3D4, func=3D1
class=3D06-07-00, hdrtype=3D0x02, mfdev=3D1
cmdreg=3D0x0003, statreg=3D0x0410, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x80 (32000 ns), maxlat=3D0x00 (0 ns)
intpin=3Db, irq=3D255
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=3D0x1106, dev=3D0x0686, revid=3D0x42
bus=3D0, slot=3D7, func=3D0
class=3D06-01-00, hdrtype=3D0x00, mfdev=3D1
cmdreg=3D0x0087, statreg=3D0x0210, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 00001c20, size 4, enabled
found-> vendor=3D0x1106, dev=3D0x0571, revid=3D0x06
bus=3D0, slot=3D7, func=3D1
class=3D01-01-8a, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0005, statreg=3D0x0290, cachelnsz=3D0 (dwords)
lattimer=3D0x40 (1920 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 00001c00, size 5, enabled
found-> vendor=3D0x1106, dev=3D0x3038, revid=3D0x1a
bus=3D0, slot=3D7, func=3D2
class=3D0c-03-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0013, statreg=3D0x0210, cachelnsz=3D8 (dwords)
lattimer=3D0x40 (1920 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Dd, irq=3D11
powerspec 2 supports D0 D3 current D0
found-> vendor=3D0x1106, dev=3D0x3057, revid=3D0x40
bus=3D0, slot=3D7, func=3D4
class=3D06-01-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0000, statreg=3D0x0290, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00001000, size 8, enabled
map[14]: type 4, range 32, base 00001c34, size 2, enabled
map[18]: type 4, range 32, base 00001c30, size 2, enabled
found-> vendor=3D0x1106, dev=3D0x3058, revid=3D0x50
bus=3D0, slot=3D7, func=3D5
class=3D04-01-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0001, statreg=3D0x0210, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Dc, irq=3D5
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base e8004000, size 11, enabled
map[14]: type 1, range 32, base e8000000, size 14, enabled
found-> vendor=3D0x104c, dev=3D0x8023, revid=3D0x00
bus=3D0, slot=3D13, func=3D0
class=3D0c-00-10, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0012, statreg=3D0x0210, cachelnsz=3D8 (dwords)
lattimer=3D0x40 (1920 ns), mingnt=3D0x02 (500 ns), maxlat=3D0x04 (1000 ns)
intpin=3Da, irq=3D5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base e8004800, size 8, enabled
map[14]: type 4, range 32, base 00001c38, size 3, enabled
map[18]: type 4, range 32, base 00001400, size 8, enabled
found-> vendor=3D0x11c1, dev=3D0x0450, revid=3D0x02
bus=3D0, slot=3D16, func=3D0
class=3D07-80-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0003, statreg=3D0x0290, cachelnsz=3D0 (dwords)
lattimer=3D0x40 (1920 ns), mingnt=3D0xfc (63000 ns), maxlat=3D0x0e (3500 n=
s)
intpin=3Da, irq=3D11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00001800, size 8, port disabled
map[14]: type 1, range 32, base e8004c00, size 10, enabled
found-> vendor=3D0x1113, dev=3D0x1216, revid=3D0x11
bus=3D0, slot=3D17, func=3D0
class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0012, statreg=3D0x0290, cachelnsz=3D8 (dwords)
lattimer=3D0x40 (1920 ns), mingnt=3D0xff (63750 ns), maxlat=3D0xff (63750 =
ns)
intpin=3Da, irq=3D11
powerspec 2 supports D0 D1 D2 D3 current D0
agp0: <VIA Generic host to PCI bridge> mem 0xec000000-0xefffffff at device =
0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xe8100000-0xe81fffff
pcib1: prefetched decode 0xf0000000-0xf7ffffff
---- initial configuration ------------------------
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 1.0.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.PIB_.LNKA irq 10: [ 10] low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=3D1
map[10]: type 1, range 32, base e8100000, size 19, enabled
map[14]: type 3, range 32, base f0000000, size 27, enabled
found-> vendor=3D0x5333, dev=3D0x8d01, revid=3D0x02
bus=3D1, slot=3D0, func=3D0
class=3D03-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0007, statreg=3D0x0230, cachelnsz=3D8 (dwords)
lattimer=3D0x40 (1920 ns), mingnt=3D0x04 (1000 ns), maxlat=3D0xff (63750 n=
s)
intpin=3Da, irq=3D10
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
cbb0: <O2Micro OZ6833 PCI-CardBus Bridge> at device 4.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: matched entry for 0.4.INTA (source \\_SB_.PCI0.PIB_.LNKA)
pcib0: slot 4 INTA is routed to irq 10
cbb1: <O2Micro OZ6833 PCI-CardBus Bridge> at device 4.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: matched entry for 0.4.INTB (source \\_SB_.PCI0.PIB_.LNKB)
pcib0: slot 4 INTB is routed to irq 11
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0x1c20-0x1c2f at device 7.1 on=
pci0
ata0: iobase=3D0x01f0 altiobase=3D0x03f6 bmaddr=3D0x1c20
ata0: mask=3D03 ostat0=3D50 ostat2=3D00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=3D03 stat0=3D50 stat1=3D00
ata0-master: ATA 01 a5
ata0: devices=3D01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=3D0x0170 altiobase=3D0x0376 bmaddr=3D0x1c28
ata1: mask=3D03 ostat0=3D50 ostat2=3D00
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 00 00
ata1: mask=3D03 stat0=3D00 stat1=3D00
ata1: devices=3D04
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x1c00-0x1c1f irq 11 at device 7.2 =
on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/11.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
isab1: <PCI-ISA bridge> at device 7.4 on pci0
isa: isa0 already exists; skipping it
pcm0: <VIA VT82C686A> port 0x1c30-0x1c33,0x1c34-0x1c37,0x1000-0x10ff irq 5 =
at device 7.5 on pci0
pcm0: ac97 codec id 0x43525934 (Cirrus Logic CS4299D)
pcm0: ac97 codec features headphone, 20 bit DAC, 18 bit ADC, 6 bit master v=
olume, Crystal Semi 3D Stereo Enhancement
pcm0: ac97 primary codec extended features variable rate PCM, AMAP
pcm0: sndbuf_setmap 715000, 1000; 0xc22a1000 -> 715000
pcm0: sndbuf_setmap 757000, 1000; 0xc22a3000 -> 757000
pci0: <serial bus, FireWire> at device 13.0 (no driver attached)
pci0: <simple comms> at device 16.0 (no driver attached)
dc0: <Accton EN2242 MiniPCI 10/100BaseTX> port 0x1800-0x18ff mem 0xe8004c00=
-0xe8004fff irq 11 at device 17.0 on pci0
dc0: Ethernet address: 00:90:96:25:f3:85
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x000749, model 0x0001, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: dc0 attached
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x=
3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xe4000-0xe7fff,0xc0000-0xcbfff on isa0
pmtimer0 on isa0
adv0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
bt0 failed to probe on isa0
cs0 failed to probe at port 0x300-0x31f on isa0
ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
fe0 failed to probe at port 0x300-0x31f on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: not probed (disabled)
sio1: not probed (disabled)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: Cannot allocate irq
sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 07 80 9c 0e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 07 80 9c 0e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=3D1023 cylinders, 0..254=3D255 heads, 1..63=3D63 sector=
s
0 accounted for
Device configuration finished.
procfs registered
Timecounters tick every 10.000 msec
bpf: lo0 attached
acpi_cpu0: set speed to 100.0%
acpi_cpu: CPU throttling enabled, 16 steps from 100% to 6.2%
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
pccard1: CIS version PC Card Standard 5.0
pccard1: CIS info: Lucent Technologies, WaveLAN/IEEE, Version 01.01,=20
pccard1: Manufacturer code 0x156, product 0x2
pccard1: function 0: network adapter, ccr addr 3e0 mask 1
pccard1: function 0, config table entry 1: I/O card; irq mask ffff; iomask =
6, iospace 0-3f; io16 irqpulse irqlevel
wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 11 function 0 config 1 on pccar=
d1
wi0: 802.11 address: 00:02:2d:65:05:ab
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station 7.28.01
wi0: wi_has_wep =3D 1
bpf: wi0 attached
acpi_cmbat0: battery initialization done, tried 1 times
ad0: success setting UDMA5 on VIA chip
GEOM: new disk ad0
ar: FreeBSD check1 failed
ad0: <FUJITSU MHR2020AT/30B8> ATA-6 disk at ata0-master
ad0: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=3D4 dmamode=3D2 udmamode=3D5 cblid=3D1
ata1-master: piomode=3D4 dmamode=3D2 udmamode=3D2 dmaflag=3D1
ata1-master: success setting PIO4 on generic chip
acd0: <TOSHIBA DVD-ROM SD-C2502/1011> DVD-ROM drive at ata1 as master
acd0: read 4134KB/s (34515KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Writes:
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm audio disc
MBR Slice 1 on ad0:
0000 00 01 01 00 0b fe 3f 23 3f 00 00 00 e5 d2 08 00 |......?#?.......|
[0] f:00 typ:11 s(CHS):0/1/1 e(CHS):35/254/63 s:63 l:578277
GEOM: Add ad0s1, start 32256 length 296077824 end 296110079
MBR Slice 2 on ad0:
0000 80 00 81 f2 a5 fe ff ff 72 d4 b8 00 0e 55 9b 01 |........r....U..|
[1] f:80 typ:165 s(CHS):242/0/129 e(CHS):255/254/255 s:12113010 l:26957070
GEOM: Add ad0s2, start 6201861120 length 13802019840 end 20003880959
MBR Slice 3 on ad0:
0000 00 00 01 24 83 fe bf c0 24 d3 08 00 5d fe a3 00 |...$....$...]...|
[2] f:00 typ:131 s(CHS):36/0/1 e(CHS):192/254/191 s:578340 l:10747485
GEOM: Add ad0s3, start 296110080 length 5502712320 end 5798822399
MBR Slice 4 on ad0:
0000 00 00 81 c1 82 fe bf f1 81 d1 ac 00 f1 02 0c 00 |................|
[3] f:00 typ:130 s(CHS):193/0/129 e(CHS):241/254/191 s:11325825 l:787185
GEOM: Add ad0s4, start 5798822400 length 403038720 end 6201861119
GEOM: Configure ad0s2a, start 0 length 134217728 end 134217727
GEOM: Configure ad0s2b, start 134217728 length 453746688 end 587964415
GEOM: Configure ad0s2c, start 0 length 13802019840 end 13802019839
GEOM: Configure ad0s2d, start 587964416 length 268435456 end 856399871
GEOM: Configure ad0s2e, start 856399872 length 268435456 end 1124835327
GEOM: Configure ad0s2f, start 1124835328 length 12677184512 end 13802019839
Mounting root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
splash: image decoder found: green_saver
Linux ELF exec handler installed
ltmdm0: <Lucent Winmodem> port 0x1400-0x14ff,0x1c38-0x1c3f mem 0xe8004800-0=
xe80048ff irq 11 at device 16.0 on pci0
ltmdm0: type Virtual 16550A
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: init failed
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0001; event status 0x0000
wi0: timeout in wi_cmd 0x000a; event status 0x0000
wi0: failed to allocate 1594 bytes on NIC
wi0: tx buffer allocation failed
wi0: timeout in wi_cmd 0x000a; event status 0x0000
wi0: failed to allocate 1594 bytes on NIC
wi0: mgmt. buffer allocation failed
wi0: timeout in wi_cmd 0x0002; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: init failed
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0001; event status 0x0000
wi0: timeout in wi_cmd 0x000a; event status 0x0000
wi0: failed to allocate 1594 bytes on NIC
wi0: tx buffer allocation failed
wi0: timeout in wi_cmd 0x000a; event status 0x0000
wi0: failed to allocate 1594 bytes on NIC
wi0: mgmt. buffer allocation failed
wi0: timeout in wi_cmd 0x0002; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: init failed
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0121; event status 0x0000
wi0: timeout in wi_cmd 0x0001; event status 0x0000
wi0: timeout in wi_cmd 0x000a; event status 0x0000
wi0: failed to allocate 1594 bytes on NIC
wi0: tx buffer allocation failed
wi0: timeout in wi_cmd 0x000a; event status 0x0000
wi0: failed to allocate 1594 bytes on NIC
wi0: mgmt. buffer allocation failed
wi0: detached
pccard1: CIS version PC Card Standard 5.0
pccard1: CIS info: Lucent Technologies, WaveLAN/IEEE, Version 01.01,=20
pccard1: Manufacturer code 0x156, product 0x2
pccard1: function 0: network adapter, ccr addr 3e0 mask 1
pccard1: function 0, config table entry 1: I/O card; irq mask ffff; iomask =
6, iospace 0-3f; io16 irqpulse irqlevel
wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 11 function 0 config 1 on pccar=
d1
wi0: 802.11 address: 00:02:2d:65:05:ab
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station 7.28.01
wi0: wi_has_wep =3D 1
bpf: wi0 attached
acpi_acad0: Notify 128
acpi_ec0: EcWaitEventIntr called without EC lock!
acpi_cmbat0: battery info corrupted
acpi_ec0: EcWaitEventIntr called without EC lock!
acpi_ec0: EcRead: Failed waiting for EC to send data.
ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
acpi_ec0: EcRead: Failed waiting for EC to send data.
ACPI-0432: *** Error: Handler for [EmbeddedControl] returned AE_ERROR
acpi_cmbat0: battery status corrupted
--=-b22uwgqH8uYp9pxr2U6T--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1036622707.750.2.camel>