Date: Tue, 13 Aug 2002 07:07:17 +0900 (JST) From: Hideyuki KURASHINA <rushani@bl.mmtr.or.jp> To: sanpei@FreeBSD.org Cc: mobile@FreeBSD.org Subject: MELCO LPC3-TX and ether-line Message-ID: <20020813.070717.07647145.rushani@bl.mmtr.or.jp>
next in thread | raw e-mail | index | archive | help
Hi, sanpei-san.
According to your commit log in src/etc/defaults/pccard.conf (rev 1.166),
fix MELCO LPC3-TX config
use ``config auto''
add ether line
but diff (-r 1.165 -r 1.166) shows that ether-line was added in the entry
`LPC3-CLX', _not_ `LPC3-TX'.
Could you fix this?
# I put "ether 0x1c8" into my /etc/pccard.conf for MELCO LPC3-TX.
P.S.
I send PR over a month at http://www.freebsd.org/cgi/query-pr.cgi?pr=39763
[dumpcis of MELCO LPC3-TX]
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x15 (Version 1 info), length = 19
000: 01 00 4d 45 4c 43 4f 00 4c 50 43 33 2d 54 58 00
010: 00 00 ff
Version = 1.0, Manuf = [MELCO], card vers = [LPC3-TX]
Addit. info = [],[]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: 01 8a ab c1
PCMCIA ID = 0x8a01, OEM ID = 0xc1ab
Tuple #4, code = 0x1a (Configuration map), length = 5
000: 01 01 c0 03 63
Reg len = 2, config register addr = 0x3c0, last config = 0x1
Registers: XX---XX-
Tuple #5, code = 0x1b (Configuration entry), length = 11
000: c7 81 19 07 55 4d 5d 65 30 ff ff
Config index = 0x7(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Card decodes 5 address lines, full 8/16 Bit I/O
IRQ modes: Level
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #6, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 20 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 40 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 60 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 00 02 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x200 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 20 02 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x220 block length = 0x20
Tuple #11, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #12, code = 0x22 (Functional EXT), length = 2
000: 01 02
Network technology: Ethernet
Tuple #13, code = 0x22 (Functional EXT), length = 2
000: 02 64
Wrong length for network extension tuple
Tuple #14, code = 0x22 (Functional EXT), length = 2
000: 03 01
Network media: UTP
Tuple #15, code = 0x14 (No link), length = 0
Tuple #16, code = 0xff (Terminator), length = 0
2 slots found
-- rushani
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020813.070717.07647145.rushani>