From owner-freebsd-questions Tue Sep 26 17: 9:50 2000 Delivered-To: freebsd-questions@freebsd.org Received: from bb.mba-consulting.com (E115025.vtacs.com [208.138.115.25]) by hub.freebsd.org (Postfix) with ESMTP id 3DF0237B424 for ; Tue, 26 Sep 2000 17:09:13 -0700 (PDT) Received: from bb.mba-consulting.com (localhost [127.0.0.1]) by bb.mba-consulting.com (8.11.0/8.9.3) with SMTP id e8R062E32152 for ; Tue, 26 Sep 2000 20:06:03 -0400 (EDT) (envelope-from hjagnew@mail.mba-consulting.com) From: "H. J. Agnew" Reply-To: hjagnew@mba-consulting.com To: questions@freebsd.org Subject: Lava's Dserial probe hangs machine Date: Tue, 26 Sep 2000 20:01:09 -0400 X-Mailer: KMail [version 1.0.28] Content-Type: text/plain MIME-Version: 1.0 Message-Id: <00092620060202.24501@bb.mba-consulting.com> Content-Transfer-Encoding: 8bit Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Just installed Lava's Dserial card in to the machine. I changed both of the on board serial ports to IRQ 3 IO 2e8 and 2f8 respectivly. Then Configured BIOS to make Lava's Dserial pci card as IRQ 4 and through the dos utility that came with the Lava card I found the IO to be d400 and d800 for the two serial ports. When I boot and config the kernel not to probe the Lava cards two serial ports everything works like it should. When I configure kernel to probe for all four serial ports each is found but when the machine progresses to the part where it waits for SCSI devices to settle the machine hangs. I have included output from dmesg just incase I over looked something but I do not see anything using d400-d407 or d800-d807. Thanks for any help. H. Jared Agnew This dmesg has all four sio's disabled in config... Copyright (c) 1992-2000 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.1-STABLE #1: Tue Sep 26 15:49:58 EDT 2000 root@bb3.mba-consulting.com:/usr/src/sys/compile/WASHINGTON Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 800032706 Hz CPU: Pentium III/Pentium III Xeon/Celeron (800.03-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x387f9ff real memory = 268369920 (262080K bytes) Preloaded elf kernel "kernel" at 0xc0324000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc03240a8. Pentium Pro MTRR support enabled md0: Malloc disk npx0: on motherboard npx0: INT 16 interface pcib0: on motherboard pci0: on pcib0 pcib1: at device 1.0 on pci0 pci1: on pcib1 pci1: at 0.0 irq 15 isab0: at device 7.0 on pci0 isa0: on isab0 pci0: at 7.1 pci0: at 7.2 chip1: port 0x5000-0x500f at device 7.3 on pci0 pci0: (vendor=0x1407, dev=0x0110) at 9.0 irq 4 pci0: (vendor=0x1407, dev=0x0111) at 9.1 irq 4 xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem 0xd9000000-0xd900007f irq 10 at device 11.0 on pci0 xl0: Ethernet address: 00:01:02:be:14:ec miibus0: on xl0 xlphy0: <3Com internal media interface> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl1: <3Com 3c905B-TX Fast Etherlink XL> port 0xe000-0xe07f mem 0xd9001000-0xd900107f irq 11 at device 13.0 on pci0 xl1: Ethernet address: 00:01:02:be:16:31 miibus1: on xl1 xlphy1: <3Com internal media interface> on miibus1 xlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ahc0: port 0xe400-0xe4ff mem 0xd9002000-0xd9002fff irq 15 at device 17.0 on pci0 ahc0: aic7892 Wide Channel A, SCSI Id=7, 16/255 SCBs fdc0: at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: at port 0x60,0x64 on isa0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> ppc0: at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode plip0: on ppbus0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 Waiting 15 seconds for SCSI devices to settle Mounting root from ufs:/dev/da0s1a da0 at ahc0 bus 0 target 6 lun 0 da0: Fixed Direct Access SCSI-3 device da0: 80.000MB/s transfers (40.000MHz, offset 127, 16bit), Tagged Queueing Enabled da0: 8759MB (17938985 512 byte sectors: 255H 63S/T 1116C) cd0 at ahc0 bus 0 target 3 lun 0 cd0: Removable CD-ROM SCSI-2 device cd0: 20.000MB/s transfers (20.000MHz, offset 16) cd0: cd present [291270 x 2048 byte records] To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message