Date: Mon, 8 Dec 2014 10:58:14 -0500 From: Justin O'Conor <oconnor@crystal.harvard.edu> To: Alan Somers <asomers@freebsd.org> Cc: FreeBSD-scsi <freebsd-scsi@freebsd.org> Subject: Re: LSI SAS 3008 card - 35 out of 36 disks detected Message-ID: <DD7EC4AD-A4B6-46F7-8F1C-9AD111DF20C6@crystal.harvard.edu> In-Reply-To: <CAOtMX2j8K3aKST1mZ%2BEMKo4OVKiR6MUy%2B1VBQ1rMams5h7Hy_w@mail.gmail.com> References: <54822835.3080800@crystal.harvard.edu> <CAOtMX2j8K3aKST1mZ%2BEMKo4OVKiR6MUy%2B1VBQ1rMams5h7Hy_w@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi All, Thanks, this is encouraging. smp_discover ses0|1 see 36 sata disks. This is from the 10.1 install. Lets start with the short ones - root@rhea:~ # sg_inq --hex --len=64 ses0 00 0d 00 05 02 34 00 40 02 4c 53 49 20 20 20 20 20 ....4.@.LSI 10 53 41 53 32 58 33 36 20 20 20 20 20 20 20 20 20 SAS2X36 20 30 65 31 32 78 33 36 2d 35 35 2e 31 34 2e 31 38 0e12x36-55.14.18 30 2e 30 00 20 20 20 20 20 .0. root@rhea:~ # sg_inq --hex --len=64 ses1 00 0d 00 05 02 34 00 40 02 4c 53 49 20 20 20 20 20 ....4.@.LSI 10 53 41 53 32 58 32 38 20 20 20 20 20 20 20 20 20 SAS2X28 20 30 65 31 32 78 33 36 2d 35 35 2e 31 34 2e 31 38 0e12x36-55.14.18 30 2e 30 00 20 20 20 20 20 root@rhea:~ # smp_discover ses0 phy 0:S:attached:[500605b009150c20:02 i(SSP+STP+SMP)] 6 Gbps phy 1:S:attached:[500605b009150c20:03 i(SSP+STP+SMP)] 6 Gbps phy 2:S:attached:[500605b009150c20:01 i(SSP+STP+SMP)] 6 Gbps phy 3:S:attached:[500605b009150c20:00 i(SSP+STP+SMP)] 6 Gbps phy 4:U:attached:[50030480017bd5bf:00 exp t(SMP)] 6 Gbps phy 5:U:attached:[50030480017bd5bf:01 exp t(SMP)] 6 Gbps phy 6:U:attached:[50030480017bd5bf:02 exp t(SMP)] 6 Gbps phy 7:U:attached:[50030480017bd5bf:03 exp t(SMP)] 6 Gbps phy 12:U:attached:[50030480017ae20c:00 t(SATA)] 6 Gbps phy 13:U:attached:[50030480017ae20d:00 t(SATA)] 6 Gbps phy 14:U:attached:[50030480017ae20e:00 t(SATA)] 6 Gbps phy 15:U:attached:[50030480017ae20f:00 t(SATA)] 6 Gbps phy 16:U:attached:[50030480017ae210:00 t(SATA)] 6 Gbps phy 17:U:attached:[50030480017ae211:00 t(SATA)] 6 Gbps phy 18:U:attached:[50030480017ae212:00 t(SATA)] 6 Gbps phy 19:U:attached:[50030480017ae213:00 t(SATA)] 6 Gbps phy 20:U:attached:[50030480017ae214:00 t(SATA)] 6 Gbps phy 21:U:attached:[50030480017ae215:00 t(SATA)] 6 Gbps phy 22:U:attached:[50030480017ae216:00 t(SATA)] 6 Gbps phy 23:U:attached:[50030480017ae217:00 t(SATA)] 6 Gbps phy 24:U:attached:[50030480017ae218:00 t(SATA)] 6 Gbps phy 25:U:attached:[50030480017ae219:00 t(SATA)] 6 Gbps phy 26:U:attached:[50030480017ae21a:00 t(SATA)] 6 Gbps phy 27:U:attached:[50030480017ae21b:00 t(SATA)] 6 Gbps phy 28:U:attached:[50030480017ae21c:00 t(SATA)] 6 Gbps phy 29:U:attached:[50030480017ae21d:00 t(SATA)] 6 Gbps phy 30:U:attached:[50030480017ae21e:00 t(SATA)] 6 Gbps phy 31:U:attached:[50030480017ae21f:00 t(SATA)] 6 Gbps phy 32:U:attached:[50030480017ae220:00 t(SATA)] 6 Gbps phy 33:U:attached:[50030480017ae221:00 t(SATA)] 6 Gbps phy 34:U:attached:[50030480017ae222:00 t(SATA)] 6 Gbps phy 35:U:attached:[50030480017ae223:00 t(SATA)] 6 Gbps phy 36:D:attached:[50030480017ae23d:00 V i(SSP+SMP) t(SSP)] 6 Gbps root@rhea:~ # foreach PHY ( `seq 0 1 36` ) foreach? smp_discover -p $PHY ses0 foreach? end Discover response: expander change count: 1328 phy identifier: 0 attached device type: SAS or SATA device attached reason: power on negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=1 stp=1 smp=1 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x500605b009150c20 attached phy identifier: 2 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 33 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x500605b009150c20 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 1 attached device type: SAS or SATA device attached reason: power on negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=1 stp=1 smp=1 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x500605b009150c20 attached phy identifier: 3 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 33 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x500605b009150c20 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 2 attached device type: SAS or SATA device attached reason: power on negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=1 stp=1 smp=1 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x500605b009150c20 attached phy identifier: 1 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 33 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x500605b009150c20 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 3 attached device type: SAS or SATA device attached reason: power on negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=1 stp=1 smp=1 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x500605b009150c20 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 33 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x500605b009150c20 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 4 attached device type: expander device attached reason: SMP phy control requested negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017bd5bf attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 4 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017bd5bf requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 5 attached device type: expander device attached reason: SMP phy control requested negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017bd5bf attached phy identifier: 1 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 4 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017bd5bf requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 6 attached device type: expander device attached reason: SMP phy control requested negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017bd5bf attached phy identifier: 2 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 4 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017bd5bf requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 7 attached device type: expander device attached reason: SMP phy control requested negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017bd5bf attached phy identifier: 3 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 4 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017bd5bf requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 8 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 9 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 10 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 11 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 12 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae20c attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 13 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae20d attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 1 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 14 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae20e attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 2 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 15 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae20f attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 3 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 16 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae210 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 4 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 17 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae211 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 5 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 18 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae212 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 6 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 19 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae213 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 7 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 20 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae214 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 8 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 21 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae215 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 9 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 22 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae216 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 10 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 23 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae217 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 11 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 24 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae218 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 12 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 25 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae219 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 13 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 26 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae21a attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 48 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 14 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 27 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae21b attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 49 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 15 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 28 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae21c attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 16 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 29 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae21d attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 17 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 30 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae21e attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 18 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 31 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae21f attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 19 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 32 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae220 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 20 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 33 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae221 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 21 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 34 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae222 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 22 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 35 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae223 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 45 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 23 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 1328 phy identifier: 36 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=1 stp=0 smp=1 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=1 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017ae23f attached SAS address: 0x50030480017ae23d attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 6 Gbps hardware minimum physical link rate: 6 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 1 partial pathway timeout value: 7 us routing attribute: direct connector type: SAS virtual connector [max 1 phy] connector element index: 24 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 1 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: root@rhea:~ # smp_discover ses1 phy 0:S:attached:[50030480017ae23f:04 exp t(SMP)] 6 Gbps phy 1:S:attached:[50030480017ae23f:05 exp t(SMP)] 6 Gbps phy 2:S:attached:[50030480017ae23f:06 exp t(SMP)] 6 Gbps phy 3:S:attached:[50030480017ae23f:07 exp t(SMP)] 6 Gbps phy 8:D:disabled phy 9:D:disabled phy 10:D:disabled phy 11:D:disabled phy 12:U:attached:[50030480017bd5ac:00 t(SATA)] 6 Gbps phy 13:U:attached:[50030480017bd5ad:00 t(SATA)] 6 Gbps phy 14:U:attached:[50030480017bd5ae:00 t(SATA)] 6 Gbps phy 15:U:attached:[50030480017bd5af:00 t(SATA)] 6 Gbps phy 16:U:attached:[50030480017bd5b0:00 t(SATA)] 6 Gbps phy 17:U:attached:[50030480017bd5b1:00 t(SATA)] 6 Gbps phy 18:U:attached:[50030480017bd5b2:00 t(SATA)] 6 Gbps phy 19:U:attached:[50030480017bd5b3:00 t(SATA)] 6 Gbps phy 20:U:attached:[50030480017bd5b4:00 t(SATA)] 6 Gbps phy 21:U:attached:[50030480017bd5b5:00 t(SATA)] 6 Gbps phy 22:U:attached:[50030480017bd5b6:00 t(SATA)] 6 Gbps phy 23:U:attached:[50030480017bd5b7:00 t(SATA)] 6 Gbps phy 24:D:disabled phy 25:D:disabled phy 26:D:disabled phy 27:D:disabled phy 28:D:attached:[50030480017bd5bd:00 V i(SSP+SMP) t(SSP)] 6 Gbps root@rhea:~ # foreach PHY ( `seq 0 1 28` ) foreach? smp_discover -p $PHY ses1 foreach? end Discover response: expander change count: 241 phy identifier: 0 attached device type: expander device attached reason: loss of dword synchronization negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017ae23f attached phy identifier: 4 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017ae23f requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 1 attached device type: expander device attached reason: loss of dword synchronization negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017ae23f attached phy identifier: 5 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017ae23f requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 2 attached device type: expander device attached reason: loss of dword synchronization negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017ae23f attached phy identifier: 6 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017ae23f requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 3 attached device type: expander device attached reason: loss of dword synchronization negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=1 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017ae23f attached phy identifier: 7 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 1 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: subtractive connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x50030480017ae23f requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 1 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 4 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 5 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 6 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 7 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled; unknown optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 8 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 9 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 10 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 11 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 12 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5ac attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 21 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 13 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5ad attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 19 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 1 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 14 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5ae attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 19 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 2 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 15 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5af attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 3 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 16 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 19 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 4 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 17 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b1 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 5 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 18 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b2 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 6 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 19 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b3 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 7 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 20 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b4 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 8 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 21 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b5 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 9 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 22 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b6 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 10 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 23 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=1 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5b7 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 18 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: table connector type: SAS Drive backplane receptacle (SFF-8482) [max 2 phys] connector element index: 11 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 24 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 25 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 26 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 27 attached device type: no device attached attached reason: unknown negotiated logical link rate: phy disabled attached initiator: ssp=0 stp=0 smp=0 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=0 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x0 attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 1.5 Gbps hardware minimum physical link rate: 1.5 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 0 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 0 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy disabled optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: Discover response: expander change count: 241 phy identifier: 28 attached device type: SAS or SATA device attached reason: unknown negotiated logical link rate: phy enabled, 6 Gbps attached initiator: ssp=1 stp=0 smp=1 sata_host=0 attached sata port selector: 0 STP buffer too small: 0 attached target: ssp=1 stp=0 smp=0 sata_device=0 SAS address: 0x50030480017bd5bf attached SAS address: 0x50030480017bd5bd attached phy identifier: 0 attached persistent capable: 0 attached power capable: 0 attached slumber capable: 0 attached partial capable: 0 attached inside ZPSDS persistent: 0 attached requested inside ZPSDS: 0 attached break_reply capable: 0 attached pwr_dis capable: 0 programmed minimum physical link rate: 6 Gbps hardware minimum physical link rate: 6 Gbps programmed maximum physical link rate: 6 Gbps hardware maximum physical link rate: 6 Gbps phy change count: 1 virtual phy: 1 partial pathway timeout value: 7 us routing attribute: direct connector type: No information connector element index: 0 connector physical link: 0 phy power condition: 0 sas power capable: 0 sas slumber capable: 0 sas partial capable: 0 sata slumber capable: 0 sata partial capable: 0 pwr_dis signal: 0 pwr_dis control capable: 0 sas slumber enabled: 0 sas partial enabled: 0 sata slumber enabled: 0 sata partial enabled: 0 attached device name: 0x0 requested inside ZPSDS changed by expander: 0 inside ZPSDS persistent: 0 requested inside ZPSDS: 0 zone group persistent: 1 inside ZPSDS: 1 zoning enabled: 0 zone group: 1 self-configuration status: 0 self-configuration levels completed: 0 self-configuration sas address: 0x0 programmed phy capabilities: 0x0 current phy capabilities: 0x0 attached phy capabilities: 0x0 reason: unknown negotiated physical link rate: phy enabled, 6 Gbps optical mode enabled: 0 negotiated SSC: 0 hardware muxing supported: 0 default inside ZPSDS persistent: 0 default requested inside ZPSDS: 0 default zone group persistent: 1 default zoning enabled: 0 default zone group: 1 saved inside ZPSDS persistent: 0 saved requested inside ZPSDS: 0 saved zone group persistent: 1 saved zoning enabled: 0 saved zone group: 1 shadow inside ZPSDS persistent: 0 shadow requested inside ZPSDS: 0 shadow zone group persistent: 1 shadow zoning enabled: 0 shadow zone group: 1 device slot number: 255 device slot group number: 255 device slot group output connector: root@rhea:~ # On Dec 5, 2014, at 5:05 PM, Alan Somers <asomers@freebsd.org> wrote: > I had a very similar problem that ended up being a bug in the expander > firmware. It was exposed by the mpr(4) driver because that driver > enumerates drives differently than mps(4) or Linux. Please install > sysutils.smp_utils and post the output of "smp_discover -p $PHY $DEV" > where $DEV is each expander (probably ses0 and ses1) and $PHY is every > phy on each expander. You can see the list of phys by doing > "smp_discover $DEV" without the "-p" option. Also, would you mind > running "sg_inq --hex --len=64 $DEV" so I know what we're working > with? > > -Alan >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?DD7EC4AD-A4B6-46F7-8F1C-9AD111DF20C6>