Date: Thu, 1 Jul 2004 15:16:07 -0400 From: "Darryl" <dts@mnsi.net> To: <freebsd-scsi@freebsd.org> Subject: cdrecord Message-ID: <001f01c45f9f$dcd5e2a0$0200a8c0@dts>
next in thread | raw e-mail | index | archive | help
Ok, I'm not sure where to go with this one so if anyone can point me in =
the right direction for this i'd be thankfull.
The problem is cdrecord will not see the the writer when -scanbus =
switch is used, but the drive does work as a CDrom. After FreeBSD was =
installed, I used "make install" for the cdrtools-2.0.3_2 package =
(Previous to freeBSD 4.10 installed was Windows 2000. No hardware has =
changed since I was able to burn CDs using EZ cd creator) Here is some =
information:
4.10-RELEASE FreeBSD 4.10-RELEASE #0: Wed Jun 23 15:08:47
ahc0: <Adaptec 2940 SCSI adapter> port 0xb800-0xb8ff mem =
0xd6800000-0xd6800fff irq 10 at device 9.0 on pci0
aic7870: Wide Channel A, SCSI Id=3D7, 16/253 SCBs
cd0 at ahc0 bus 0 target 6 lun 0
cd0: <RICOH MP6200S 2.40> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: cd present [1 x 2048 byte records]
prompt# camcontrol devlist
<COMPAQPC FIREBALL1080S 1Q09> at scbus0 target 0 lun 0 (pass0,da0)
<QUANTUM LIGHTNING 540S 241E> at scbus0 target 1 lun 0 (pass1,da1)
<IBM DCAS-34330 !# S65A> at scbus0 target 2 lun 0 (pass2,da2)
<IBM DCAS-34330 !# S69D> at scbus0 target 3 lun 0 (pass3,da3)
<RICOH MP6200S 2.40> at scbus0 target 6 lun 0 (pass4,cd0)
prompt# cdrecord -scanbus
cdrecord: warning: low file descriptor limit (93)
Cdrecord 2.00.3 (i386-unknown-freebsd4.10) Copyright (C) 1995-2002 =
J=F6rg Schilling
Using libscg version 'schily-0.7'
scsibus0:
0,0,0 0) 'COMPAQPC' 'FIREBALL1080S ' '1Q09' Disk
0,1,0 1) 'QUANTUM ' 'LIGHTNING 540S ' '241E' Disk
0,2,0 2) 'IBM ' 'DCAS-34330 !#' 'S65A' Disk
0,3,0 3) 'IBM ' 'DCAS-34330 !#' 'S69D' Disk
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
The whole kernel config can be found here: =
http://www.mnsi.net/~dts/kernel/kernel.txt
At this point i'm not sure why the system can find the Ricoh RW drive =
and cdrecord can't. I don't know much about configuring the kernel for =
such a scsi device, and I don't know much about camcontrol. But I do =
think these have something to do with why cdrecord doesn't see it. Any =
information at all would help me greatly.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?001f01c45f9f$dcd5e2a0$0200a8c0>