Date: Fri, 08 Apr 2005 22:08:13 +0200 From: Attila Nagy <bra@fsn.hu> To: freebsd-sparc64@freebsd.org Subject: dmesg from an oldie (E3000) Message-ID: <4256E4AD.1030100@fsn.hu>
next in thread | raw e-mail | index | archive | help
Hello, I've just throwed a FreeBSD 5.4-RC CD-ROM into this machine to see whether it boots or not. I've yet to try its "big" brother, which has 6 336 MHz US-II processors. Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... nothing to autoload yet. jumping to kernel entry at 0xc0040000. stray vector interrupt 241 Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.4-RC1 #0: Mon Apr 4 05:54:28 UTC 2005 root@binkley.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC real memory = 3623878656 (3456 MB) avail memory = 3505438720 (3343 MB) cpu0: Sun Microsystems UltraSparc-I Processor (168.00 MHz CPU) cpu1: Sun Microsystems UltraSparc-I Processor (168.00 MHz CPU) cpu2: Sun Microsystems UltraSparc-I Processor (168.00 MHz CPU) cpu3: Sun Microsystems UltraSparc-I Processor (168.00 MHz CPU) cpu4: Sun Microsystems UltraSparc-I Processor (168.00 MHz CPU) cpu5: Sun Microsystems UltraSparc-I Processor (168.00 MHz CPU) FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs nexus0: <Open Firmware Nexus device> central0: <central> on nexus0 fhc0: <fhc> on central0 eeprom0: <EEPROM/clock> mem 0x908000-0x909fff on fhc0 eeprom0: model mk48t59 eeprom0: hostid 8081d787 puc0: <Zilog Z8530 dual channel SCC> mem 0x902000-0x902007 on fhc0 uart0: <z8530, channel A> on puc0 uart0: console (9600,n,8,1) uart1: <z8530, channel B> on puc0 puc1: <Zilog Z8530 dual channel SCC> mem 0x904000-0x904007 on fhc0 uart2: <z8530, channel A> on puc1 uart3: <z8530, channel B> on puc1 fhc0: <clock-board> mem 0x90c000,0x906000-0x90605f,0x900000-0x900005 type unknown (no driver attached) fhc1: <fhc> on nexus0 fhc1: <ac> mem 0x2000000-0x2ffffff,0x1000000-0x1007fff type memory-controller (no driver attached) fhc1: <simm-status> mem 0x600000-0x60000f type unknown (no driver attached) fhc1: <environment> mem 0x400000-0x40000f type unknown (no driver attached) fhc1: <sram> mem 0x280000-0x287fff,0x200000-0x207fff type unknown (no driver attached) fhc1: <flashprom> mem 0-0x7ffff type unknown (no driver attached) fhc2: <fhc> on nexus0 fhc2: <ac> mem 0x2000000-0x2ffffff,0x1000000-0x1007fff type memory-controller (no driver attached) fhc2: <simm-status> mem 0x600000-0x60000f type unknown (no driver attached) fhc2: <environment> mem 0x400000-0x40000f type unknown (no driver attached) fhc2: <sram> mem 0x280000-0x287fff,0x200000-0x207fff type unknown (no driver attached) fhc2: <flashprom> mem 0-0x7ffff type unknown (no driver attached) fhc3: <fhc> on nexus0 fhc3: <ac> mem 0x2000000-0x2ffffff,0x1000000-0x1007fff type memory-controller (no driver attached) fhc3: <simm-status> mem 0x600000-0x60000f type unknown (no driver attached) fhc3: <environment> mem 0x400000-0x40000f type unknown (no driver attached) fhc3: <sram> mem 0x280000-0x287fff,0x200000-0x207fff type unknown (no driver attached) fhc3: <flashprom> mem 0-0x7ffff type unknown (no driver attached) sbus0: clock 25.000 MHz sbus dvma: DVMA map: 0xfc000000 to 0xffffffff initializing counter-timer Timecounter "counter-timer" frequency 1000000 Hz quality 100 sbus0: <U2S UPA-SBus bridge> on nexus0 sbus0: <SUNW,soc>, type (unknown) (no driver attached) hme0: <Sun HME 10/100 Ethernet> mem 0x8c07000-0x8c0701f,0x8c06000-0x8c07fff,0x8c04000-0x8c05fff,0x8c02000-0x8c03fff,0x8c0000 0-0x8c00107 irq 140 on sbus0 miibus0: <MII bus> on hme0 qsphy0: <QS6612 10/100 media interface> on miibus0 qsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme0: Ethernet address: 08:00:20:9e:4b:a8 hme1: <Sun HME 10/100 Ethernet> mem 0x8c17000-0x8c1701f,0x8c16000-0x8c17fff,0x8c14000-0x8c15fff,0x8c12000-0x8c13fff,0x8c1000 0-0x8c10107 irq 140 on sbus0 miibus1: <MII bus> on hme1 qsphy1: <QS6612 10/100 media interface> on miibus1 qsphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme1: Ethernet address: 08:00:20:9e:4b:a9 hme2: <Sun HME 10/100 Ethernet> mem 0x8c27000-0x8c2701f,0x8c26000-0x8c27fff,0x8c24000-0x8c25fff,0x8c22000-0x8c23fff,0x8c2000 0-0x8c20107 irq 140 on sbus0 miibus2: <MII bus> on hme2 qsphy2: <QS6612 10/100 media interface> on miibus2 qsphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme2: Ethernet address: 08:00:20:9e:4b:aa hme3: <Sun HME 10/100 Ethernet> mem 0x8c37000-0x8c3701f,0x8c36000-0x8c37fff,0x8c34000-0x8c35fff,0x8c32000-0x8c33fff,0x8c3000 0-0x8c30107 irq 140 on sbus0 miibus3: <MII bus> on hme3 qsphy3: <QS6612 10/100 media interface> on miibus3 qsphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme3: Ethernet address: 08:00:20:9e:4b:ab hme4: <Sun HME 10/100 Ethernet> mem 0x8c07000-0x8c0701f,0x8c06000-0x8c07fff,0x8c04000-0x8c05fff,0x8c02000-0x8c03fff,0x8c0000 0-0x8c00107 irq 148 on sbus0 miibus4: <MII bus> on hme4 nsphy0: <DP83840 10/100 media interface> on miibus4 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme4: Ethernet address: 08:00:20:81:d7:87 esp0: <Sun FAS366 Fast-Wide SCSI> mem 0x8810000-0x881003f,0x8800000-0x880000f irq 147 on sbus0 esp0: FAS366/HME, 40MHz, SCSI ID 7 fhc4: <fhc> on nexus0 fhc4: <ac> mem 0x2000000-0x2ffffff,0x1000000-0x1007fff type memory-controller (no driver attached) fhc4: <environment> mem 0x400000-0x40000f type unknown (no driver attached) fhc4: <flashprom> mem 0-0x7ffff type unknown (no driver attached) eeprom1: <EEPROM/clock> mem 0x300000-0x301fff on fhc4 eeprom1: model mk48t59 eeprom1: hostid 8081d787 fhc4: <sbus-speed> mem 0x500000-0x50000f type unknown (no driver attached) sbus1: clock 25.000 MHz sbus dvma: DVMA map: 0xfc000000 to 0xffffffff initializing counter-timer Timecounter "counter-timer" frequency 1000000 Hz quality 100 sbus1: <U2S UPA-SBus bridge> on nexus0 hme5: <Sun HME 10/100 Ethernet> mem 0x8c07000-0x8c0701f,0x8c06000-0x8c07fff,0x8c04000-0x8c05fff,0x8c02000-0x8c03fff,0x8c0000 0-0x8c00107 irq 220 on sbus1 miibus5: <MII bus> on hme5 nsphy1: <DP83840 10/100 media interface> on miibus5 nsphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme5: Ethernet address: 08:00:20:81:d7:87 esp1: <Sun FAS366 Fast-Wide SCSI> mem 0x8810000-0x881003f,0x8800000-0x880000f irq 219 on sbus1 esp1: FAS366/HME, 40MHz, SCSI ID 7 sbus1: <SUNW,socal>, type socal (no driver attached) Timecounters tick every 10.000 msec Waiting 15 seconds for SCSI devices to settle md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc04b6010 SMP: AP CPU #5 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #1 Launched! cd0 at esp1 bus 0 target 6 lun 0 cd0: <TOSHIBA XM-5401TASUN4XCD 1036> Removable CD-ROM SCSI-2 device cd0: 4.032MB/s transfers (4.032MHz, offset 15) cd0: cd present [1023968 x 512 byte records] da0 at esp1 bus 0 target 0 lun 0 da0: <SEAGATE ST32171W SUN2.1G 7462> Fixed Direct Access SCSI-2 device da0: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 2029MB (4157201 512 byte sectors: 255H 63S/T 258C) da1 at esp1 bus 0 target 1 lun 0 da1: <SEAGATE ST32171W SUN2.1G 3862> Fixed Direct Access SCSI-2 device da1: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da1: 2029MB (4157201 512 byte sectors: 255H 63S/T 258C) da2 at esp1 bus 0 target 2 lun 0 da2: <SEAGATE ST32171W SUN2.1G 7462> Fixed Direct Access SCSI-2 device da2: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da2: 2029MB (4157201 512 byte sectors: 255H 63S/T 258C) da3 at esp1 bus 0 target 3 lun 0 da3: <SEAGATE ST32171W SUN2.1G 7462> Fixed Direct Access SCSI-2 device da3: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da3: 2029MB (4157201 512 byte sectors: 255H 63S/T 258C) da4 at esp1 bus 0 target 10 lun 0 da4: <SEAGATE ST318404LSUN18G 4207> Fixed Direct Access SCSI-3 device da4: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da4: 17274MB (35378533 512 byte sectors: 255H 63S/T 2202C) da5 at esp1 bus 0 target 14 lun 0 da5: <FUJITSU MAG3182L SUN18G 1111> Fixed Direct Access SCSI-2 device da5: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da5: 17274MB (35378533 512 byte sectors: 255H 63S/T 2202C) da6 at esp1 bus 0 target 15 lun 0 da6: <SEAGATE ST39204LCSUN9.0G 4207> Fixed Direct Access SCSI-3 device da6: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled da6: 8637MB (17689267 512 byte sectors: 255H 63S/T 1101C) Mounting root from ufs:/dev/md0 The box has two 5k2 disk boxes connected to it via FC-AL (the real disks are "there". Is it impossible to get them working? prtdiag says: ========================= IO Cards ========================= Bus Freq Brd Type MHz Slot Name Model --- ---- ---- ---- -------------------------------- ---------------------- 1 SBus 25 0 SUNW,socal/sf (scsi-3) 501-5266 1 SBus 25 1 SUNW,qfe SUNW,sbus-qfe 1 SBus 25 1 SUNW,qfe SUNW,sbus-qfe 1 SBus 25 1 SUNW,qfe SUNW,sbus-qfe 1 SBus 25 1 SUNW,qfe SUNW,sbus-qfe 1 SBus 25 2 SUNW,hme SUNW,501-2739 1 SBus 25 2 SUNW,fas/sd (block) 1 SBus 25 3 SUNW,hme 1 SBus 25 3 SUNW,fas/sd (block) 1 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060 -- Attila Nagy e-mail: Attila.Nagy@fsn.hu Free Software Network (FSN.HU) phone @work: +361 371 3536 ISOs: http://www.fsn.hu/?f=download cell.: +3630 306 6758
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4256E4AD.1030100>