Date: Tue, 21 Mar 2006 07:57:42 -0500 (EST) From: jason kawaja <kawaja@ece.ufl.edu> To: freebsd-scsi@freebsd.org Subject: qlogic isp 6312 device not showing up Message-ID: <Pine.BSF.4.62.0603210739370.17308@felix.ece.ufl.edu>
next in thread | raw e-mail | index | archive | help
ibm xseries 346, dual xeon dual core with qlogic fc card. external disk device shows up within the qlogic bios (once wwid is correctly added to the disk array manager,ibm shark) however does not show from within freebsd. any ideas? information below. thank you. ------------ uname -imprs ------------ FreeBSD 6.0-RELEASE-p3 i386 i386 EBSD --------------------- camcontrol devlist -v --------------------- scbus0 on isp0 bus 0: < > at scbus0 target -1 lun -1 () scbus1 on ahd0 bus 0: < > at scbus1 target -1 lun -1 () scbus2 on ahd1 bus 0: <IBM-ESXS VPR073C3-ETS10FN S3C0> at scbus2 target 0 lun 0 (da0,pass0) <IBM-ESXS VPR073C3-ETS10FN S3C0> at scbus2 target 1 lun 0 (da1,pass1) <IBM 39M6750a S320 0 1> at scbus2 target 8 lun 0 (ses0,pass2) < > at scbus2 target -1 lun -1 () scbus-1 on xpt0 bus 0: < > at scbus-1 target -1 lun -1 (xpt0) --------------------------------- dmesg output of relevant sections --------------------------------- CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2800.13-MHz 686-class CPU) <SNIP> isp0: <Qlogic ISP 6312 PCI FC-AL Adapter> port 0x4000-0x40ff mem 0xdefff000-0xdeffffff irq 96 at device 4.0 on pci4 isp0: [GIANT-LOCKED] isp0: bad hard address 125- resetting to zero <SNIP> acd0: DVDROM <MATSHITADVD-ROM SR-8178/PJ31> at ata0-master UDMA33 Waiting 5 seconds for SCSI devices to settle (probe278:ahd1:0:8:0): No or incomplete CDB sent to device. ahd1: Issued Channel A Bus Reset. 5 SCBs aborted ses0 at ahd1 bus 0 target 8 lun 0 ses0: <IBM 39M6750a S320 0 1> Fixed Processor SCSI-2 device ses0: 3.300MB/s transfers ses0: SAF-TE Compliant Device SMP: AP CPU #7 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #5 Launched! da0 at ahd1 bus 0 target 0 lun 0 da0: <IBM-ESXS VPR073C3-ETS10FN S3C0> Fixed Direct Access SCSI-4 device da0: 320.000MB/s transfers (160.000MHz, offset 127, 16bit), Tagged Queueing Enabled da0: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) da1 at ahd1 bus 0 target 1 lun 0 da1: <IBM-ESXS VPR073C3-ETS10FN S3C0> Fixed Direct Access SCSI-4 device da1: 320.000MB/s transfers (160.000MHz, offset 127, 16bit), Tagged Queueing Enabled da1: 70006MB (143374000 512 byte sectors: 255H 63S/T 8924C) Trying to mount root from ufs:/dev/da0s1a bge0: link state changed to UP bge1: link state changed to UP -- Jason Kawaja 2-4568 http://www.ietf.org/rfc/rfc1855.txt
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.62.0603210739370.17308>