Date: Tue, 04 Oct 2005 20:36:37 -0500 From: Brian John <brianjohn@fusemail.com> To: freebsd-questions@freebsd.org Subject: Re: 5.4 reboots when I plug in a flash drive? Message-ID: <43432E25.6060907@fusemail.com> In-Reply-To: <44achoiy8p.fsf@be-well.ilk.org> References: <1468.209.87.176.132.1128439684.fusewebmail-19592@webmail.fusemail.com > <20051005000110.GA51496@holestein.holy.cow> <43431D86.40903@fusemail.com> <44achoiy8p.fsf@be-well.ilk.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Lowell Gilbert wrote: >Brian John <brianjohn@fusemail.com> writes: > > > >>Parv wrote: >> >> >> >>>in message >>><1468.209.87.176.132.1128439684.fusewebmail-19592@webmail.fusemail.com >>> >>> >>> >>>>, wrote Brian John thusly... >>>> >>>>I just got a 128MB USB flash drive. When I plug it in in FreeBSD, >>>>the box promptly reboots! What would cause this? >>>> >>>> >>>> >>>I don't know the cause. >>> >>>Have you tried booting FreeBSD from power-off state w/ the flash >>>drive already inserted? That may solve your booting problem, but >>>will not make use of the drive any easier. >>> >>>Which version if FreeBSD are you using? Which of the [ueo]hci >>>drivers come up in dmesg(8) on instertion of the USB drive? >>> >>> >>> - Parv >>> >>> >>> >>> >>Ok, I tried booting up with the drive installed. If I leave it >>installed while it is booting up, it eventually reboots. However, I >>was able to unplug it during boot and look at dmesg. It says this >>over and over again: >> >>umass0: vendor 0x10d6 USB 2.0(FS) FLASH DISK, rev 1.10/1.00, addr 2 >>da0 at umass-sim0 bus 0 target 0 lun 0 >>da0: <USB2.0 (FS) FLASH DISK 1.00> Removable Direct Access SCSI-0 device >>da0: 1.000MB/s transfers >>da0: 119MB (245473 512 byte sectors: 64H 32S/T 119C) >>umass0: BBB reset failed, STALLED >>umass0: BBB bulk-in clear stall failed, STALLED >>umass0: BBB bulk-out clear stall failed, STALLED >>(da0:umass-sim0:0:0:0): Synchronize cache failed, status == 0x4, scsi >>status == 0x0 >>umass0: BBB reset failed, STALLED >>umass0: BBB bulk-in clear stall failed, STALLED >>umass0: BBB bulk-out clear stall failed, STALLED >>umass0: BBB reset failed, STALLED >>umass0: BBB bulk-in clear stall failed, STALLED >>umass0: BBB bulk-out clear stall failed, STALLED >>umass0: BBB reset failed, STALLED >>umass0: BBB bulk-in clear stall failed, STALLED >>umass0: BBB bulk-out clear stall failed, STALLED >>umass0: BBB reset failed, STALLED >>umass0: BBB bulk-in clear stall failed, STALLED >>umass0: BBB bulk-out clear stall failed, STALLED >>umass0: BBB reset failed, STALLED >>umass0: BBB bulk-in clear stall failed, STALLED >>umass0: BBB bulk-out clear stall failed, STALLED >>umass0: at uhub2 port 1 (addr 2) disconnected >>(da0:umass-sim0:0:0:0): lost device >>(da0:umass-sim0:0:0:0): removing device entry >>Opened disk da0 -> 5 >>umass0: detached >> >>I am running FreeBSD 5.4. Does this shed some light on the problem? >> >> > >Only a little. Do you have udbp(4) in your kernel? >Can you try booting 6.0 with the flash unit plugged in and see if it >still has problems? > > > I could try it, but I don't want to have to roll 6.0 back to 5.4 afterward if it doesn't work. Upgrading to 6.0 is a major change and I only have 1 PC. I am still kind of a novice, how easy is it to upgrade to 6.0 and how stable is it? I see that I have the line with udbp commented out in my kernel config. Should I rebuild with it uncommented? #device udbp # USB Double Bulk Pipe devices Thanks /Brian
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?43432E25.6060907>