Date: Sat, 2 Jul 2022 19:42:43 -0700 From: Mark Millard <marklmi@yahoo.com> To: bob prohaska <fbsd@www.zefox.net> Cc: Free BSD <freebsd-arm@freebsd.org> Subject: Re: RPi3 usb boot hang on stable/13 Message-ID: <8C389C8E-3F44-4F25-BDF4-44313026E2F8@yahoo.com> In-Reply-To: <C6340631-C9A0-4153-8571-041B695CB2E2@yahoo.com> References: <20220702165800.GA10701@www.zefox.net> <3BDD64A4-8BC3-4E14-B17C-1958F6CBB87F@yahoo.com> <24D669B0-728D-4910-884A-B2230AE442F9@yahoo.com> <20220702222139.GB10701@www.zefox.net> <C6340631-C9A0-4153-8571-041B695CB2E2@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 2022-Jul-2, at 18:38, Mark Millard <marklmi@yahoo.com> wrote: > On 2022-Jul-2, at 15:21, bob prohaska <fbsd@www.zefox.net> wrote: >=20 >> On Sat, Jul 02, 2022 at 12:00:02PM -0700, Mark Millard wrote: >>> On 2022-Jul-2, at 10:34, Mark Millard <marklmi@yahoo.com> wrote: >>>>>=20 >>>>> Device 0:=20 >>>>=20 >>>> That is U-Boot output. Looks like the output stopped before >>>> the load of even the FreeBSD loader: FreeBSD is not involved >>>> yet so it is not a FreeBSD problem. >>>=20 >>> Hmm. I looked at an old RPI3 boot-session log I have around and >>> it shows more text than you report. Is your serial connection >>> having problems? An example that is missing is the line >>> "U-Boot . . ." that identifies the version and build time >>> of U-Boot. That is rather generic material to be missing. >>> (I did not have a microsd card present. Such could be an >>> example of expected differences.) >>>=20 >>>=20 >>> There is the difference (yours then mine): >>>=20 >>> MMC: mmc@7e300000: 1 >>> vs. >>> MMC: mmc@7e300000: 2 >>>=20 >>> I wonder it if is some sort of clue about something. >>>=20 >>=20 >> It just dawned there are two u-boot instances: One on the microSD, >> which I think is the "special USB boot" version, which reports >> U-Boot 2019.10 (Mar 17 2020 - 22:01:14 -0700) >=20 > The above is what you are using when you use the microsd > card. See later. >=20 >> and a second on the FAT partition of the USB disk, which reports >> U-Boot 2020.10 (Apr 09 2021 - 03:55:54 +0000) >=20 > You are not using the above one when you use the microsd card. >=20 > You are using the above one if it gets to U-Boot without a > microsd card present. >=20 >> Just tried removing the microSD card and issuing shutdown -r now. >> The console got to "Resetting system..." and stopped.=20 >>=20 >> Put the microSD back in and tried again from the beginning. It looks >> like the machine starts from microSD and transfers control to u-boot >> on the USB drive. >=20 > No: See later. >=20 >> The USB boot OTP was set IIRC, haven't checked lately. >> Maybe it's time to reformat and start over..... >>=20 >> What follows is a fairly typical startup session: >>=20 >> Resetting system ...=20 >>=20 >>=20 >> Raspberry Pi Bootcode >>=20 >> Found SD card, config.txt =3D 1, start.elf =3D 1, recovery.elf =3D 0, = timeout =3D 0 >> Read File: config.txt, 178 (bytes) >>=20 >>=20 >>=20 >>=20 >> Raspberry Pi Bootcode >> Read File: config.txt, 178 >> Read File: start.elf, 2835780 (bytes) >> Read File: fixup.dat, 6639 (bytes) >> MESS:00:00:01.108743:0: brfs: File read: /mfs/sd/config.txt >=20 > /mfs/sd/ is the microsd card in your context. >=20 Note: The above was based on your reporting that the microsd card was used. If no microsd card was present and USB was being used, it would still say: /mfs/sd/ as the path prefix. That notation in the RPi* firmware output just means the boot media used by the RPi* firmware. Other than the "just bootcode on the microsd card" alternative, the RPi* firmware picks one place and gets everything that it loads from there. Any accesses to other partitions or media are not by RPi* firmware once the RPi* firmware has made its pick. > The above is config.txt being loaded from the microsd card. >=20 >> MESS:00:00:01.112989:0: brfs: File read: 178 bytes >> MESS:00:00:01.126707:0: HDMI:EDID error reading EDID block 0 attempt = 0 >> MESS:00:00:01.132784:0: HDMI:EDID error reading EDID block 0 attempt = 1 >> MESS:00:00:01.139029:0: HDMI:EDID error reading EDID block 0 attempt = 2 >> MESS:00:00:01.145279:0: HDMI:EDID error reading EDID block 0 attempt = 3 >> MESS:00:00:01.151529:0: HDMI:EDID error reading EDID block 0 attempt = 4 >> MESS:00:00:01.157779:0: HDMI:EDID error reading EDID block 0 attempt = 5 >> MESS:00:00:01.164029:0: HDMI:EDID error reading EDID block 0 attempt = 6 >> MESS:00:00:01.170279:0: HDMI:EDID error reading EDID block 0 attempt = 7 >> MESS:00:00:01.176529:0: HDMI:EDID error reading EDID block 0 attempt = 8 >> MESS:00:00:01.182779:0: HDMI:EDID error reading EDID block 0 attempt = 9 >> MESS:00:00:01.188792:0: HDMI:EDID giving up on reading EDID block 0 >> MESS:00:00:01.206550:0: brfs: File read: /mfs/sd/config.txt >=20 > The above is config.txt (again!) being loaded from the microsd card. >=20 >> MESS:00:00:01.210671:0: HDMI:Setting property pixel encoding to = Default >> MESS:00:00:01.216761:0: HDMI:Setting property pixel clock type to PAL >> MESS:00:00:01.222920:0: HDMI:Setting property content type flag to No = data >> MESS:00:00:01.229520:0: HDMI:Setting property fuzzy format match to = enabled >> MESS:00:00:01.236297:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK = not defined >> MESS:00:00:01.439246:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK = not defined >> MESS:00:00:01.445328:0: hdmi: HDMI:hdmi_get_state is deprecated, use = hdmi_get_display_state instead >> MESS:00:00:01.453811:0: hdmi: HDMI:>>>>>>>>>>>>>Rx sensed, reading = EDID<<<<<<<<<<<<< >> MESS:00:00:01.461557:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 0 >> MESS:00:00:01.469289:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 1 >> MESS:00:00:01.476056:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 2 >> MESS:00:00:01.482826:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 3 >> MESS:00:00:01.489597:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 4 >> MESS:00:00:01.496368:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 5 >> MESS:00:00:01.503138:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 6 >> MESS:00:00:01.509910:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 7 >> MESS:00:00:01.516681:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 8 >> MESS:00:00:01.523451:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 9 >> MESS:00:00:01.529985:0: hdmi: HDMI:EDID giving up on reading EDID = block 0 >> MESS:00:00:01.535499:0: hdmi: HDMI: No lookup table for resolution = group 0 >> MESS:00:00:01.542084:0: hdmi: HDMI: hotplug attached with DVI support >> MESS:00:00:01.548262:0: hdmi: HDMI:hdmi_get_state is deprecated, use = hdmi_get_display_state instead >> MESS:00:00:01.557298:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 0 >> MESS:00:00:01.565030:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 1 >> MESS:00:00:01.571802:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 2 >> MESS:00:00:01.578573:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 3 >> MESS:00:00:01.585343:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 4 >> MESS:00:00:01.592115:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 5 >> MESS:00:00:01.598886:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 6 >> MESS:00:00:01.605656:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 7 >> MESS:00:00:01.612427:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 8 >> MESS:00:00:01.619198:0: hdmi: HDMI:EDID error reading EDID block 0 = attempt 9 >> MESS:00:00:01.625732:0: hdmi: HDMI:EDID giving up on reading EDID = block 0 >> MESS:00:00:01.631505:0: hdmi: HDMI: hotplug deassert >> MESS:00:00:01.635919:0: hdmi: HDMI: HDMI is currently off >> MESS:00:00:01.641039:0: hdmi: HDMI: changing mode to unplugged >> MESS:00:00:01.646605:0: hdmi: HDMI:hdmi_get_state is deprecated, use = hdmi_get_display_state instead >> MESS:00:00:01.656008:0: *** Restart logging >> MESS:00:00:01.659280:0: brfs: File read: 178 bytes >> MESS:00:00:01.665054:0: Failed to open command line file = 'cmdline.txt' >> MESS:00:00:01.672773:0: brfs: File read: /mfs/sd/armstub8.bin >=20 > The above is armstub8.bin being loaded from the microsd card. >=20 >> MESS:00:00:01.676824:0: Loading 'armstub8.bin' to 0x0 size 0x1700 >> MESS:00:00:01.682667:0: brfs: File read: 5888 bytes >> MESS:00:00:01.718268:0: brfs: File read: /mfs/sd/u-boot.bin >=20 > The above is u-boot.bin being loaded from the microsd card. >=20 >> MESS:00:00:01.722146:0: Loading 'u-boot.bin' to 0x80000 size 0x7a2d8 >> MESS:00:00:01.731830:0: No kernel trailer - assuming DT-capable >> MESS:00:00:01.736078:0: brfs: File read: 500440 bytes >> MESS:00:00:01.743877:0: brfs: File read: /mfs/sd/bcm2710-rpi-3-b.dtb >=20 > The above is bcm2710-rpi-3-b.dtb being loaded from the microsd card. >=20 >> MESS:00:00:01.748535:0: Loading 'bcm2710-rpi-3-b.dtb' to 0xfa2d8 size = 0x5f12 >> MESS:00:00:01.889271:0: brfs: File read: 24338 bytes >> MESS:00:00:01.892986:0: brfs: File read: /mfs/sd/config.txt >=20 > The above is config.txt (again!) being loaded from the microsd card. >=20 >> MESS:00:00:01.897876:0: dtparam: audio=3Don >> MESS:00:00:01.919689:0: dtparam: i2c_arm=3Don >> MESS:00:00:01.938056:0: dtparam: spi=3Don >> MESS:00:00:01.954303:0: brfs: File read: 178 bytes >> MESS:00:00:01.959758:0: brfs: File read: /mfs/sd/overlays/mmc.dtbo >=20 > The above is overlays/mmc.dtbo being loaded from the microsd card. >=20 >> MESS:00:00:01.981176:0: Loaded overlay 'mmc' >> MESS:00:00:02.030370:0: brfs: File read: 1099 bytes >> MESS:00:00:02.034426:0: brfs: File read: /mfs/sd/overlays/pwm.dtbo >=20 > The above is overlays/pwm.dtbo being loaded from the microsd card. >=20 >> MESS:00:00:02.051824:0: Loaded overlay 'pwm' >> MESS:00:00:02.087719:0: brfs: File read: 946 bytes >> MESS:00:00:02.091725:0: brfs: File read: = /mfs/sd/overlays/pi3-disable-bt.dtbo >=20 > The above is overlays/pi3-disable-bt.dtbo being loaded from the = microsd card. >=20 >> MESS:00:00:02.115336:0: Loaded overlay 'pi3-disable-bt' >> MESS:00:00:03.175615:0: gpioman: gpioman_get_pin_num: pin EMMC_ENABLE = not defined >> MESS:00:00:03.287931:0: Device tree loaded to 0x4000 (size 0x63cd) >> MESS:00:00:03.293589:0: uart: Set PL011 baud rate to 103448.300000 Hz >> MESS:00:00:03.300125:0: uart: Baud rate change done... >> MESS:00:00:03.303554:0: uart: Baud rate change done... >> MESS:00:00:03.309236:0: gpioman: gpioman_get_pin_num: pin = SDCARD_CONTROL_POWER not defined >=20 > There is missing text from U-Boot here. >=20 > But the below is from the U-Boot on the microsd card. > Try renaming it, copying an alternative version, > and seeing what it does? Repeat . . . ? >=20 >> MMC: mmc@7e300000: 1 >> Loading Environment from FAT... OK >> In: serial >> Out: vidconsole >> Err: vidconsole >> Net: No ethernet found. >> starting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> Hit any key to stop autoboot: 0=20 >>=20 >> Device 0: unknown device >> U-Boot> usb reset >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> U-Boot> usb reset >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> U-Boot> usb reset >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> U-Boot> power-cycled hub >> Unknown command 'power-cycled' - try 'help' >> U-Boot> usb reset >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> U-Boot> usb reset >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> U-Boot> editenv usb_pgood_delay >> edit: 3200 >> U-Boot> editenv usb_pgood_delay >> edit: 19000 >>=20 >> [saveenv results in "saving to FAT failed"] >>=20 >> U-Boot> usb reset >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 0 Storage Device(s) found >> U-Boot>=20 >> resetting USB... >> Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB = Device(s) found >> scanning usb for storage devices... 1 Storage Device(s) found >> U-Boot> boot =20 >>=20 >> Device 0: Vendor: SABRENT Rev: 1214 Prod:=20 >> Type: Hard Disk >> Capacity: 953869.7 MB =3D 931.5 GB (1953525168 x 512) >> ... is now current device >> Scanning usb 0:1... >> Found EFI removable media binary efi/boot/bootaa64.efi >=20 > The path is not explicit enough to directly indicate the > microsd card vs. the USB drive. But the above is one > of the (possibly) 2 FreeBSD loaders you have in your > environment. >=20 >> libfdt fdt_check_header(): FDT_ERR_BADMAGIC >> Scanning disk mmc@7e300000.blk... >> Scanning disk usb_mass_storage.lun0... >> Found 5 disks >> BootOrder not defined >> EFI boot manager: Cannot load any image >> 1259212 bytes read in 676 ms (1.8 MiB/s) >> libfdt fdt_check_header(): FDT_ERR_BADMAGIC >>=20 >> [whitespace omitted] >=20 > The below is from one of the FreeBSD loaders. >=20 >> Consoles: EFI console =20 >> Reading loader env vars from /efi/freebsd/loader.env >> Setting currdev to disk1p1: >> FreeBSD/arm64 EFI loader, Revision 1.1 >>=20 >> Command line arguments: loader.efi >> Image base: 0x39e06000 >> EFI version: 2.80 >> EFI Firmware: Das U-Boot (rev 8217.4096) >> Console: comconsole (0) >> Load Path: /efi\boot\bootaa64.efi >> Load Device: = /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x0)= /UsbClass(0x424,0x9514,0x9,0x0,0x2)/UsbClass(0x5e3,0x610,0x9,0x0,0x1)/UsbC= lass(0x152d,0x583,0x0,0x0,0x0)/HD(1,MBR,0x76573018,0x81f,0x18fa8) >> Trying ESP: = /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x0)= /UsbClass(0x424,0x9514,0x9,0x0,0x2)/UsbClass(0x5e3,0x610,0x9,0x0,0x1)/UsbC= lass(0x152d,0x583,0x0,0x0,0x0)/HD(1,MBR,0x76573018,0x81f,0x18fa8) >> Setting currdev to disk1p1: >> Trying: = /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x0)= /UsbClass(0x424,0x9514,0x9,0x0,0x2)/UsbClass(0x5e3,0x610,0x9,0x0,0x1)/UsbC= lass(0x152d,0x583,0x0,0x0,0x0)/HD(2,MBR,0x76573018,0x197c7,0x746ed5e9) >> Setting currdev to disk1p2: >=20 > "disk1p2:" is from the USB drive (based on the long line before it). >=20 > I expect that this means that the FreeBSD loader was also from > the USB drive. >=20 >> Loading /boot/defaults/loader.conf >> Loading /boot/defaults/loader.conf >> Loading /boot/device.hints >> Loading /boot/loader.conf >> Loading /boot/loader.conf.local >> Loading kernel... >> /boot/kernel/kernel text=3D0x2a8 text=3D0x89ef40 text=3D0x1fb30c = data=3D0x1a9358 data=3D0x0+0x2a8000 syms=3D[0x8+0x121740+0x8+0x1454aa] >> Loading configured modules... >> /boot/kernel/filemon.ko text=3D0x1574 text=3D0x272c data=3D0x500+0x20 = syms=3D[0x8+0xcd8+0x8+0x7c5] >> /boot/kernel/umodem.ko text=3D0x2160 text=3D0x1400 data=3D0x6e8+0x10 = syms=3D[0x8+0xf48+0x8+0xb75] >> loading required module 'ucom' >> /boot/kernel/ucom.ko text=3D0x249f text=3D0x3360 data=3D0x8a0+0x858 = syms=3D[0x8+0x1188+0x8+0xb19] >> /boot/entropy size=3D0x1000 >> /etc/hostid size=3D0x25 >>=20 >> Hit [Enter] to boot immediately, or any other key for command prompt. >> Booting [/boot/kernel/kernel]... =20 >> Using DTB provided by EFI at 0x7ef6000. >> EFI framebuffer information: >> addr, size 0x3eaf0000, 0x10a800 >> dimensions 656 x 416 >> stride 656 >> masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000 >> ---<<BOOT>>--- >=20 > This is about where the kernel output starts. >=20 >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB = compliance >=20 > The dtb files used do not have freebsd specific content. As I > understand, for RPi*'s, the above is expected. >=20 >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, = 1994 >> The Regents of the University of California. All rights = reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-STABLE #5 stable/13-n251597-7c500f98b8d: Fri Jul 1 = 21:52:12 PDT 2022 >> bob@pelorus.zefox.org:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC = arm64 >> FreeBSD clang version 14.0.5 = (https://github.com/llvm/llvm-project.git = llvmorg-14.0.5-0-gc12386ae247c) >> VT(efifb): resolution 656x416 >> module firmware already present! >> real memory =3D 993988608 (947 MB) >> avail memory =3D 947646464 (903 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f42000 mode 2 pages 1 >> MAP 39f4d000 mode 2 pages 1 >> MAP 3b350000 mode 2 pages 16 >> MAP 3f100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> lintc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on = simplebus0 >> intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq = 20 on simplebus0 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq = 22,23 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 21 = on simplebus0 >> generic_timer0: <ARMv7 Generic Timer> irq 0,1,2,3 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality = 1000 >> Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality = 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq = 4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19 on simplebus0 >> bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100027 on = simplebus0 >> bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on = simplebus0 >> bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e10400f on = simplebus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e201fff irq 24 on = simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e204fff irq 26 = on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq = 37 on simplebus0 >> bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> = mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 43,44 on simplebus0 >> usbus1 on bcm283x_dwcotg0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem = 0x7e300000-0x7e3000ff irq 46 on simplebus0 >> mmc0: <MMC/SD bus> on sdhci_bcm0 >> fb0: <BCM2835 VT framebuffer driver> on simplebus0 >> fb0: keeping existing fb bpp of 32 >> fbd0 on fb0 >> WARNING: Device "fb" is Giant locked and may be deleted before = FreeBSD 14.0. >> VT: Replacing driver "efifb" with new "fb". >> fb0: 656x416(656x416@0,0) 32bpp >> fb0: fbswap: 1, pitch 2624, base 0x3eaf0000, screen_size 1091584 >> pmu0: <Performance Monitoring Unit> irq 50 on simplebus0 >> cpulist0: <Open Firmware CPU Group> on ofwbus0 >> cpu0: <Open Firmware CPU> on cpulist0 >> bcm2835_cpufreq0: <CPU Frequency Control> on cpu0 >> cpu1: <Open Firmware CPU> on cpulist0 >> cpu2: <Open Firmware CPU> on cpulist0 >> cpu3: <Open Firmware CPU> on cpulist0 >> gpioled0: <GPIO LEDs> on ofwbus0 >> gpioled0: <led0> failed to map pin >> gpioled0: <led1> failed to map pin >> armv8crypto0: CPU lacks AES instructions >> Timecounters tick every 1.000 msec >> iicbus0: <OFW I2C bus> on iichb0 >> iic0: <I2C generic I/O> on iicbus0 >> usbus1: 480Mbps High Speed USB v2.0 >> ugen1.1: <DWCOTG OTG Root HUB> at usbus1 >> uhub0 on usbus1 >> uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on = usbus1 >> mmcsd0: 32GB <SDHC SE32G 8.0 SN 29ED3EF6 MFG 09/2015 by 3 SD> at mmc0 = 50.0MHz/4bit/65535-block >> bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF >> CPU 0: ARM Cortex-A53 r0p4 affinity: 0 >> Cache Type =3D <64 byte D-cacheline,64 byte = I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> >> Instruction Set Attributes 0 =3D <CRC32> >> Instruction Set Attributes 1 =3D <> >> Processor Features 0 =3D <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 = 32> >> Processor Features 1 =3D <> >> Memory Model Features 0 =3D <TGran4,TGran64,SNSMem,BigEnd,16bit = ASID,1TB PA> >> Trying to mount root from ufs:/dev/da0s2a [rw]... >> Memory Model Features 1 =3D <8bit VMID> >> Memory Model Features 2 =3D <32bit CCIDX,48bit VA> >> Debug Features 0 =3D <DoubleLock,2 CTX BKPTs,4 = Watchpoints,6 Breakpoints,PMUv3,Debugv8> >> Debug Features 1 =3D <> >> Auxiliary Features 0 =3D <> >> Auxiliary Features 1 =3D <> >> AArch32 Instruction Set Attributes 5 =3D <CRC32,SEVL> >> AArch32 Media and VFP Features 0 =3D <FPRound,FPSqrt,FPDivide,DP = VFPv3+v4,SP VFPv3+v4,AdvSIMD> >> AArch32 Media and VFP Features 1 =3D <SIMDFMAC,FPHP DP Conv,SIMDHP SP = Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ> >> CPU 1: ARM Cortex-A53 r0p4 affinity: 1 >> CPU 2: ARM Cortex-A53 r0p4 affinity: 2 >> CPU 3: ARM Cortex-A53 r0p4 affinity: 3 >> Release APs...done >> uhub0: 1 port with 1 removable, self powered >> ugen1.2: <vendor 0x0424 product 0x9514> at usbus1 >> uhub1 on uhub0 >> uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr = 2> on usbus1 >> uhub1: MTT enabled >> Root mount waiting for: usbus1 CAM >> uhub1: 5 ports with 4 removable, self powered >> ugen1.3: <vendor 0x0424 product 0xec00> at usbus1 >> smsc0 on uhub1 >> smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on = usbus1 >> smsc0: chip 0xec00, rev. 0002 >> miibus0: <MII bus> on smsc0 >> smscphy0: <SMC LAN8700 10/100 interface> PHY 1 on miibus0 >> smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> ue0: <USB Ethernet> on smsc0 >> ue0: Ethernet address: b8:27:eb:71:46:4e >> Root mount waiting for: usbus1 CAM >> ugen1.4: <GenesysLogic USB2.1 Hub> at usbus1 >> uhub2 on uhub1 >> uhub2: <GenesysLogic USB2.1 Hub, class 9/0, rev 2.10/6.55, addr 4> on = usbus1 >> uhub2: 4 ports with 4 removable, self powered >> Root mount waiting for: usbus1 CAM >> usb_msc_auto_quirk: UQ_MSC_NO_GETMAXLUN set for USB mass storage = device JMicron SABRENT (0x152d:0x0583) >> usb_msc_auto_quirk: UQ_MSC_NO_PREVENT_ALLOW set for USB mass storage = device JMicron SABRENT (0x152d:0x0583) >> Root mount waiting for: usbus1 CAM >> ugen1.5: <JMicron SABRENT> at usbus1 >> umass0 on uhub2 >> umass0: <JMicron SABRENT, class 0/0, rev 2.10/12.14, addr 5> on = usbus1 >> umass0: SCSI over Bulk-Only; quirks =3D 0x8100 >> umass0:0:0: Attached to scbus0 >> ugen1.6: <FTDI FT232R USB UART> at usbus1 >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> Root mount waiting for: CAM >> da0 at umass-sim0 bus 0 scbus0 target 0 lun 0 >> da0: <SABRENT 1214> Fixed Direct Access SPC-4 SCSI device >> da0: Serial Number 000000000000A >> da0: 40.000MB/s transfers >> da0: 953869MB (1953525168 512 byte sectors) >> da0: quirks=3D0x2<NO_6_BYTE> >> Warning: no time-of-day clock registered, system time will not be set = accurately >> Dual Console: Serial Primary, Video Secondary >> Setting hostuuid: 30303030-3030-3030-3064-626136386435. >> Setting hostid: 0x5cd40a6a. >> Starting file system checks: >> /dev/da0s2a: FILE SYSTEM CLEAN; SKIPPING CHECKS >> /dev/da0s2a: clean, 291525 free (4757 frags, 35846 blocks, 0.6% = fragmentation) >> /dev/da0s2d: FILE SYSTEM CLEAN; SKIPPING CHECKS >> /dev/da0s2d: clean, 225584444 free (104508 frags, 28184992 blocks, = 0.0% fragmentation) >=20 > /dev/da0s2a vs. /dev/da0s2d ? But both seem to have worked. >=20 >> Mounting local filesystems:. >> ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib = /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg = /usr/local/lib/perl5/5.32/mach/CORE >> Setting hostname: pelorus.zefox.org. >> Setting up harvesting: = [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,A= TTACH,CACHED >> Feeding entropy: . >> lo0: link state changed to UP >> smsc0: chip 0xec00, rev. 0002 >> ue0: link state changed to DOWN >> ue0: link state changed to UP >> Starting Network: lo0 ue0. >> lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 >> options=3D680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>= >> inet6 ::1 prefixlen 128 >> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 >> inet 127.0.0.1 netmask 0xff000000 >> groups: lo >> nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL> >> ue0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 = mtu 1500 >> options=3D80009<RXCSUM,VLAN_MTU,LINKSTATE> >> ether b8:27:eb:71:46:4e >> inet 50.1.20.24 netmask 0xffffff00 broadcast 50.1.20.255 >> media: Ethernet autoselect (100baseTX <full-duplex>) >> status: active >> nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> >> Starting devd. >> Autoloading module: uftdi.ko >> uftdi0 on uhub1 >> uftdi0: <FT232R USB UART> on usbus1 >> add host 127.0.0.1: gateway lo0 fib 0: route already in table >> add net default: gateway 50.1.20.1 >> add host ::1: gateway lo0 fib 0: route already in table >> add net fe80::: gateway ::1 >> add net ff02::: gateway ::1 >> add net ::ffff:0.0.0.0: gateway ::1 >> add net ::0.0.0.0: gateway ::1 >> Clearing /tmp (X related). >> Updating /var/run/os-release done. >> Creating and/or trimming log files. >> Updating motd:. >> Starting syslogd. >> Setting date via ntp. >> 2 Jul 15:05:36 ntpdate[805]: step time server 212.7.1.131 offset = +1584.319871 sec >> Starting powerd. >> Mounting late filesystems:. >> Starting sendmail. >> Starting sendmail_msp_queue. >> Starting cron. >> Configuring vt: blanktime. >> Performing sanity check on sshd configuration. >> Starting sshd. >> Starting background file system checks in 60 seconds. >>=20 >> Sat Jul 2 15:05:44 PDT=20 >> FreeBSD/arm64 (pelorus.zefox.org) (ttyu0) >>=20 >> login: >=20 =3D=3D=3D Mark Millard marklmi at yahoo.com
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?8C389C8E-3F44-4F25-BDF4-44313026E2F8>