Date: Mon, 18 Oct 1999 19:13:44 -0700 From: pheath@fhcrc.org To: aic7xxx@freebsd.org Subject: 2930cu Message-ID: <7ugk4o$lsso@eGroups.com>
next in thread | raw e-mail | index | archive | help
OK, I am running Linux 6.0. If I compile the aic7xxx support into the
kernel I get the following message over and over when trying to
configure 2930CU SCSI controller. If it is compiled as a module my
first PCI SCSI Card works fine (2940U2W), but the 2930 is only seen by
the BIOS, but not acknoledged by the kernel.
SCSI0:-1:-1:-1) Referenced SCB 13 not valid during SELTO
SCSISEQ=0x5a SEQADDR=0x8 SSATO=0x10 SSTAT1=0x88
SCSI0:-1:-1:-1) Referenced SCB 13 not valid during SELTO
SCSISEQ=0x5a SEQADDR=0x9 SSATO=0x10 SSTAT1=0x88
(These are repeated many times, then it says:)
SCSI Host 1 channel 0 reset(PID 74) Timed out-trying harder
SCSI Bus is being reset for host 1 channel 0
(Then it does the above lines many times, and ......over and over till
I stop it)
cat /proc/pci gives the following when it boots without the kernel
recognizing it.
cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel 440BX - 82443BX Host (rev 3).
Medium devsel. Master Capable. Latency=64.
Prefetchable 32 bit memory at 0xf4000000 [0xf4000008].
Bus 0, device 1, function 0:
PCI bridge: Intel 440BX - 82443BX AGP (rev 3).
Medium devsel. Master Capable. Latency=64. Min Gnt=136.
Bus 0, device 7, function 0:
ISA bridge: Intel 82371AB PIIX4 ISA (rev 2).
Medium devsel. Fast back-to-back capable. Master Capable. No
bursts.
Bus 0, device 7, function 1:
IDE interface: Intel 82371AB PIIX4 IDE (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable.
Latency=32.
I/O at 0xffa0 [0xffa1].
Bus 0, device 7, function 2:
USB Controller: Intel 82371AB PIIX4 USB (rev 1).
Medium devsel. Fast back-to-back capable. IRQ 11. Master
Capable. Late
ncy=64.
I/O at 0xdce0 [0xdce1].
Bus 0, device 7, function 3:
Bridge: Intel 82371AB PIIX4 ACPI (rev 2).
Medium devsel. Fast back-to-back capable.
Bus 0, device 13, function 0:
SCSI storage controller: Adaptec AHA-2940U2 (rev 0).
Medium devsel. Fast back-to-back capable. BIST capable. IRQ
10. Master
Capable. Latency=64. Min Gnt=39.Max Lat=25.
I/O at 0xd800 [0xd801].
Non-prefetchable 64 bit memory at 0xff001000 [0xff001004].
Bus 0, device 14, function 0:
SCSI storage controller: Adaptec Unknown device (rev 3).
Vendor id=9004. Device id=3860.
Medium devsel. Fast back-to-back capable. IRQ 9. Master
Capable. Laten
cy=64. Min Gnt=4.Max Lat=4.
I/O at 0xd400 [0xd401].
Non-prefetchable 32 bit memory at 0xff000000 [0xff000000].
Bus 0, device 17, function 0:
Ethernet controller: 3Com 3C905B 100bTX (rev 36).
Medium devsel. IRQ 11. Master Capable. Latency=64. Min
Gnt=10.Max Lat=
10.
I/O at 0xdc00 [0xdc01].
Non-prefetchable 32 bit memory at 0xff002000 [0xff002000].
Bus 1, device 0, function 0:
VGA compatible controller: ATI Unknown device (rev 122).
Vendor id=1002. Device id=4757.
Medium devsel. Fast back-to-back capable. IRQ 10. Master
Capable. Late
ncy=64. Min Gnt=8.
Non-prefetchable 32 bit memory at 0xfd000000 [0xfd000000].
I/O at 0xec00 [0xec01].
Non-prefetchable 32 bit memory at 0xfcfff000 [0xfcfff000].
Any ideas?
Pat
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7ugk4o$lsso>