Date: Tue, 19 Dec 2006 18:03:54 +0100 From: Palle Girgensohn <girgen@FreeBSD.org> To: Shigeaki Tagashira <shigeaki@se.hiroshima-u.ac.jp> Cc: questions@FreeBSD.org, obrien@FreeBSD.org Subject: Re: if_nfe on nVidia chipset Message-ID: <06DA4ABFFA1F59DF90AE0285@rambutan.pingpong.net> In-Reply-To: <45841980.5090100@se.hiroshima-u.ac.jp> References: <92F17ADAEC575CF1EDBE870C@rambutan.pingpong.net> <45841980.5090100@se.hiroshima-u.ac.jp>
next in thread | previous in thread | raw e-mail | index | archive | help
--On s=F6ndag, december 17, 2006 01.06.24 +0900 Shigeaki Tagashira=20 <shigeaki@se.hiroshima-u.ac.jp> wrote: > I have the same one. And if_nfe works well on it, in both FreeBSD > 6.2-PRERELEASE and 7-CURRENT. Please try to initialize if_nfe using > ifconfig command; ># ifconfig nfe1 down; ifconfig nfe1 up > > --- > S. Tagashira Hi Tagashira-san, Tried a lot of stuff, up and down and also "debug" flag, but nothing helps. ifconfig says "media: Ethernet autoselect (none)" I can ping the interface itself, but nothing else. Any ideas? Regards, Palle > > Palle Girgensohn wrote: >> Hi! Sorry for the cross post, I'd love to know if I can get this working >> or not. >> >> Regards, >> Palle >> >> ---------- Forwarded Message ---------- >> Date: tisdag, december 12, 2006 18.52.35 +0100 >> From: Palle Girgensohn <girgen@FreeBSD.org> >> To: hardware@freebsd.org >> Subject: if_nfe on Asus M2N-SLI deluxe? >> >> Hi! >> >> Does anybody know if if_nfe should work on the above motherboard? I >> snached the patch for FreeBSD-6.2 from >> <http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html>; = and >> tried it. The kernel and ifconfig seems happy, but it does not work; >> ifconfig reports "active" but ifconfig reports: >> >> nfe0: flags=3D8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 >> options=3D1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING> >> ether 00:17:31:86:aa:31 >> media: Ethernet autoselect (none) >> status: no carrier >> nfe1: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >> options=3D1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING> >> inet6 fe80::217:31ff:fe86:b4c6%nfe1 prefixlen 64 scopeid 0x4 >> inet 192.168.1.191 netmask 0xffffff00 broadcast 192.168.1.255 >> ether 00:17:31:86:b4:c6 >> media: Ethernet autoselect (none) >> status: active >> lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 >> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 >> scopeid 0x5 inet 127.0.0.1 netmask 0xff000000 >> The media part of nfe1 looks bad, eh? >> >> Is it supposed to work? How can I help to get it working? >> >> FreeBSD 6.2-stable, around RC1. Enclosed is a dmesg. Anything else >> needed? >> >> /Palle >> >> >> >> ---------- End Forwarded Message ---------- >> >> >> >> >> ------------------------------------------------------------------------ >> >> Subject: >> if_nfe on Asus M2N-SLI deluxe? >> From: >> Palle Girgensohn <girgen@FreeBSD.org> >> Date: >> Tue, 12 Dec 2006 18:52:35 +0100 >> To: >> hardware@freebsd.org >> >> To: >> hardware@freebsd.org >> CC: >> obrien@freebsd.org >> >> >> Hi! >> >> Does anybody know if if_nfe should work on the above motherboard? I >> snached the patch for FreeBSD-6.2 from >> <http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html>; = and >> tried it. The kernel and ifconfig seems happy, but it does not work; >> ifconfig reports "active" but ifconfig reports: >> >> nfe0: flags=3D8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 >> options=3D1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING> >> ether 00:17:31:86:aa:31 >> media: Ethernet autoselect (none) >> status: no carrier >> nfe1: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >> options=3D1b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING> >> inet6 fe80::217:31ff:fe86:b4c6%nfe1 prefixlen 64 scopeid >> 0x4 inet 192.168.1.191 netmask 0xffffff00 broadcast 192.168.1.255 >> ether 00:17:31:86:b4:c6 >> media: Ethernet autoselect (none) >> status: active >> lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 >> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 >> scopeid 0x5 inet 127.0.0.1 netmask 0xff000000 >> The media part of nfe1 looks bad, eh? >> >> Is it supposed to work? How can I help to get it working? >> >> FreeBSD 6.2-stable, around RC1. Enclosed is a dmesg. Anything else >> needed? >> >> /Palle >> >> >> >> ------------------------------------------------------------------------ >> >> Copyright (c) 1992-2006 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 6.2-PRERELEASE #0: Wed Nov 29 11:57:06 CET 2006 >> girgen@rambutan.pingpong.net:/usr/obj/.a/banan/usr/src/sys/WORKSTATI >> ON Timecounter "i8254" frequency 1193182 Hz quality 0 >> CPU: AMD Athlon(tm) 64 Processor 3500+ (2210.20-MHz 686-class CPU) >> Origin =3D "AuthenticAMD" Id =3D 0x40ff2 Stepping =3D 2 >> = Features=3D0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG >> E,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> >> Features2=3D0x2001<SSE3,CX16> >> AMD = Features=3D0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow+,3DNow> >> AMD Features2=3D0x1d<LAHF,<b2>,<b3>,CR8> >> real memory =3D 2146369536 (2046 MB) >> avail memory =3D 2091245568 (1994 MB) >> ACPI APIC Table: <Nvidia AWRDACPI> >> ioapic0 <Version 1.1> irqs 0-23 on motherboard >> acpi0: <Nvidia AWRDACPI> on motherboard >> acpi_bus_number: can't get _ADR >> acpi_bus_number: can't get _ADR >> acpi_bus_number: can't get _ADR >> acpi_bus_number: can't get _ADR >> acpi0: Power Button (fixed) >> acpi_bus_number: can't get _ADR >> acpi_bus_number: can't get _ADR >> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 >> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 >> cpu0: <ACPI CPU> on acpi0 >> acpi_button0: <Power Button> on acpi0 >> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 >> pci0: <ACPI PCI bus> on pcib0 >> pci0: <memory, RAM> at device 0.0 (no driver attached) >> isab0: <PCI-ISA bridge> at device 1.0 on pci0 >> isa0: <ISA bus> on isab0 >> pci0: <serial bus, SMBus> at device 1.1 (no driver attached) >> pci0: <memory, RAM> at device 1.2 (no driver attached) >> ohci0: <OHCI (generic) USB controller> mem 0xfe02f000-0xfe02ffff irq 21 >> at device 2.0 on pci0 ohci0: [GIANT-LOCKED] >> usb0: OHCI version 1.0, legacy support >> usb0: SMM does not respond, resetting >> usb0: <OHCI (generic) USB controller> on ohci0 >> usb0: USB revision 1.0 >> uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >> uhub0: 10 ports with 10 removable, self powered >> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe02e000-0xfe02e0ff irq >> 22 at device 2.1 on pci0 ehci0: [GIANT-LOCKED] >> usb1: EHCI version 1.0 >> usb1: companion controller, 10 ports each: usb0 >> usb1: <EHCI (generic) USB 2.0 controller> on ehci0 >> usb1: USB revision 2.0 >> uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 >> uhub1: 10 ports with 10 removable, self powered >> atapci0: <nVidia nForce MCP55 UDMA133 controller> port >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf400-0xf40f at device 4.0 on pci0 >> ata0: <ATA channel 0> on atapci0 >> ata1: <ATA channel 1> on atapci0 >> atapci1: <nVidia nForce MCP55 SATA300 controller> port >> 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xe000-0xe00f mem >> 0xfe02d000-0xfe02dfff irq 23 at device 5.0 on pci0 ata2: <ATA channel 0> >> on atapci1 >> ata3: <ATA channel 1> on atapci1 >> atapci2: <nVidia nForce MCP55 SATA300 controller> port >> 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xcc00-0xcc0f mem >> 0xfe02c000-0xfe02cfff irq 20 at device 5.1 on pci0 ata4: <ATA channel 0> >> on atapci2 >> ata5: <ATA channel 1> on atapci2 >> atapci3: <nVidia nForce MCP55 SATA300 controller> port >> 0xc800-0xc807,0xc400-0xc403,0xc000-0xc007,0xbc00-0xbc03,0xb800-0xb80f >> mem 0xfe02b000-0xfe02bfff irq 21 at device 5.2 on pci0 ata6: <ATA >> channel 0> on atapci3 >> ata7: <ATA channel 1> on atapci3 >> pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0 >> pci1: <ACPI PCI bus> on pcib1 >> fxp0: <Intel 82558 Pro/100 Ethernet> port 0xac00-0xac1f mem >> 0xfdeff000-0xfdefffff,0xfdc00000-0xfdcfffff irq 16 at device 6.0 on pci1 >> miibus0: <MII bus> on fxp0 >> inphy0: <i82555 10/100 media interface> on miibus0 >> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> fxp0: Ethernet address: 00:a0:c9:ce:11:26 >> fwohci0: <Texas Instruments TSB43AB22/A> mem >> 0xfddff000-0xfddff7ff,0xfddf8000-0xfddfbfff irq 19 at device 11.0 on = pci1 >> fwohci0: OHCI version 1.10 (ROM=3D1) >> fwohci0: No. of Isochronous channels is 4. >> fwohci0: EUI64 00:11:d8:00:00:c8:2b:85 >> fwohci0: Phy 1394a available S400, 2 ports. >> fwohci0: Link S400, max_rec 2048 bytes. >> firewire0: <IEEE1394(FireWire) bus> on fwohci0 >> fwe0: <Ethernet over FireWire> on firewire0 >> if_fwe0: Fake Ethernet address: 02:11:d8:c8:2b:85 >> fwe0: Ethernet address: 02:11:d8:c8:2b:85 >> fwe0: if_start running deferred for Giant >> sbp0: <SBP-2/SCSI over FireWire> on firewire0 >> fwohci0: Initiate bus reset >> fwohci0: node_id=3D0xc800ffc0, gen=3D1, CYCLEMASTER mode >> firewire0: 1 nodes, maxhop <=3D 0, cable IRM =3D 0 (me) >> firewire0: bus manager 0 (me) >> pci0: <multimedia> at device 6.1 (no driver attached) >> nfe0: <NVIDIA nForce MCP55 Networking Adapter> port 0xb400-0xb407 mem >> 0xfe02a000-0xfe02afff,0xfe029000-0xfe0290ff,0xfe028000-0xfe02800f irq 23 >> at device 8.0 on pci0 miibus1: <MII bus> on nfe0 >> e1000phy0: <Marvell 88E1116 Gigabit PHY> on miibus1 >> e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, >> 1000baseTX-FDX, auto nfe0: Ethernet address: 00:17:31:86:aa:31 >> nfe1: <NVIDIA nForce MCP55 Networking Adapter> port 0xb000-0xb007 mem >> 0xfe027000-0xfe027fff,0xfe026000-0xfe0260ff,0xfe025000-0xfe02500f irq 20 >> at device 9.0 on pci0 miibus2: <MII bus> on nfe1 >> e1000phy1: <Marvell 88E1116 Gigabit PHY> on miibus2 >> e1000phy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, >> 1000baseTX-FDX, auto nfe1: Ethernet address: 00:17:31:86:b4:c6 >> pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0 >> pci2: <ACPI PCI bus> on pcib2 >> pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0 >> pci3: <ACPI PCI bus> on pcib3 >> pcib4: <ACPI PCI-PCI bridge> at device 12.0 on pci0 >> pci4: <ACPI PCI bus> on pcib4 >> pcib5: <ACPI PCI-PCI bridge> at device 13.0 on pci0 >> pci5: <ACPI PCI bus> on pcib5 >> pcib6: <ACPI PCI-PCI bridge> at device 14.0 on pci0 >> pci6: <ACPI PCI bus> on pcib6 >> atapci4: <JMicron JMB363 SATA300 controller> port >> 0x9c00-0x9c07,0x9800-0x9803,0x9400-0x9407,0x9000-0x9003,0x8c00-0x8c0f >> mem 0xfdafe000-0xfdafffff irq 16 at device 0.0 on pci6 atapci4: AHCI >> Version 01.00 controller with 2 ports detected >> ata8: <ATA channel 0> on atapci4 >> ata9: <ATA channel 1> on atapci4 >> ata10: <ATA channel 2> on atapci4 >> pcib7: <ACPI PCI-PCI bridge> at device 15.0 on pci0 >> pci7: <ACPI PCI bus> on pcib7 >> nvidia0: <GeForce 6200 TurboCache(TM)> mem >> 0xfa000000-0xfaffffff,0xe0000000-0xefffffff,0xfb000000-0xfbffffff irq 16 >> at device 0.0 on pci7 nvidia0: [GIANT-LOCKED] >> acpi_tz0: <Thermal Zone> on acpi0 >> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on >> acpi0 fdc0: [FAST] >> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on >> acpi0 sio0: type 16550A >> ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0 >> ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode >> ppbus0: <Parallel port bus> on ppc0 >> ppi0: <Parallel I/O> on ppbus0 >> lpt0: <Printer> on ppbus0 >> lpt0: Interrupt-driven port >> pmtimer0 on isa0 >> orm0: <ISA Option ROMs> at iomem 0xd0000-0xd3fff,0xd4000-0xd67ff on isa0 >> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >> kbd0 at atkbd0 >> atkbd0: [GIANT-LOCKED] >> sc0: <System console> at flags 0x100 on isa0 >> sc0: VGA <16 virtual consoles, flags=3D0x300> >> sio1: configured irq 3 not in bitmap of probed irqs 0 >> sio1: port may not be enabled >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on = isa0 >> ukbd0: Logitech HID compliant keyboard, rev 1.10/1.80, addr 2, iclass = 3/1 >> kbd1 at ukbd0 >> uhid0: Logitech HID compliant keyboard, rev 1.10/1.80, addr 2, iclass = 3/1 >> ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/18.00, addr 3, iclass = 3/1 >> ums0: 6 buttons and Z dir. >> Timecounter "TSC" frequency 2210201999 Hz quality 800 >> Timecounters tick every 0.801 msec >> ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding >> disabled, default to accept, logging disabled ad0: 152627MB <Seagate >> ST3160212A 3.AAJ> at ata0-master UDMA100 acd0: DVDR <Optiarc DVD RW >> AD-5170A/1.11> at ata0-slave UDMA66 >> cd0 at ata0 bus 0 target 1 lun 0 >> cd0: <Optiarc DVD RW AD-5170A 1.11> Removable CD-ROM SCSI-0 device >> cd0: 66.000MB/s transfers >> cd0: Attempt to query device size failed: NOT READY, Medium not present >> Trying to mount root from ufs:/dev/ad0s1a >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> freebsd-hardware@freebsd.org mailing list >> http://lists.freebsd.org/mailman/listinfo/freebsd-hardware >> To unsubscribe, send any mail to >> "freebsd-hardware-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?06DA4ABFFA1F59DF90AE0285>