Date: Tue, 26 Apr 2005 20:34:40 +0200 From: Roland Smith <rsmith@xs4all.nl> To: freebsd-questions@freebsd.org Cc: Broming plutonium <zhangzhaoxi2003@yahoo.ca> Subject: Re: Connecting to the Internet Message-ID: <20050426183440.GA27747@slackbox.xs4all.nl> In-Reply-To: <20050425230736.3763.qmail@web51402.mail.yahoo.com> References: <20050425230736.3763.qmail@web51402.mail.yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable
On Mon, Apr 25, 2005 at 07:07:35PM -0400, Broming plutonium wrote:
> Hello everyone...for the first time.
> =20
> I have two computers. I very recently installed FreeBSD on my first
> computer because the operating system it used to have, Microsoft
> Windows, was infected by so many viruses that my computer took a
> million years to open a program.
:-)=20
=20
> I've only had 2 days of experience with FreeBSD, so I don't know
> anything about it. How do I connect it to the Internet using Ethernet?
> My computer seemed to be telling me it had three network
> interfaces. I'm guessing that the ones called plip0 and ppp0 are all
> wrong; sl0 is the right one.
FreeBSD comes with a handbook. You can find it on your disk at=20
/usr/share/doc/en_US.ISO8859-1/books/handbook/book.html (HTML version)
/usr/share/doc/en_US.ISO8859-1/books/handbook/book.txt (plain text version)
You can view the text version with the command=20
'less /usr/share/doc/en_US.ISO8859-1/books/handbook/book.txt'
If you have the X window system running, and have a web browser (mozilla
or firefox) installed, reading the HTML version is probably nicer.
> FreeBSD tries to establish an Internet connection on plip0 every time
> it boots. How do I change that to sl0? How do I tell it to "tell DHCP
> server to assign IP address xxx.xxx.xxx.xxx on subnet mask
> xxx.xxx.xxx.xxx USING the sl0 network interface?
If you run the command 'ifconfig', you'll see which interfaces are
available. On my system it returns this:
re0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=3D18<VLAN_MTU,VLAN_HWTAGGING>
inet 10.0.0.150 netmask 0xffffff00 broadcast 10.0.0.255
ether 00:11:09:8b:c2:58
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
plip0: flags=3D108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000=20
You can forget about plip0 (it is shown because the system has a
parallel port) and lo0 (that's the loopback interface). In my case re0
is the ethernet card.
To see if you have a active ethernet card, run the following command
(without the quote-marks)
'dmesg|grep Ethernet'
On my system it returns:
re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0xd400-0xd4ff mem=20
0xcfffbf00-0xcfffbfff irq 16 at device 11.0 on pci0
re0: Ethernet address: 00:11:09:8b:c2:58
This shows that I have a RealTek ethernet chip, that uses the re
driver. It is also listed in the ifconfig output.
> What do I have to do to establish an Internet connection? Any help
> would be appreciated. Thanks!
That depends. We need more information in order to tell you anything
usefull. Do you have a DSL modem that has an ethernet connection? Or do
you dial in via a modem?
Roland
--=20
R.F. Smith /"\ ASCII Ribbon Campaign
r s m i t h @ x s 4 a l l . n l \ / No HTML/RTF in e-mail
http://www.xs4all.nl/~rsmith/ X No Word docs in e-mail
public key: http://www.keyserver.net / \ Respect for open standards
--ReaqsoxgOBHFXBhH
Content-Type: application/pgp-signature
Content-Disposition: inline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.1 (FreeBSD)
iD8DBQFCbonAEnfvsMMhpyURAt4UAJ9fPbrfrmg/AkAYiHYjh3VwOOQVqwCdE7fv
Ulqc8a7N93c/SFO939zKjjw=
=ql+Q
-----END PGP SIGNATURE-----
--ReaqsoxgOBHFXBhH--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050426183440.GA27747>